Vivo DESK-V103E User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v103e
SKU: DESK-V103E
Black Electric Dual Motor Desk Frame
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Telescopic
Crossbar
B(x2)
Side
Bracket
C(x2)
Foot
S-A (x8)
M6x10 Bolt
S-B (x8 )
M6x16 Bolt
S-C (x10)
7/8" Screw
S-D (x2)
3/4" Screw
H(x2)
Hook
D (x1)
Shelf
E (x2)
Liing
Column
F (x1)
Fixing Plate
G (x1)
Control Unit
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
S-E (x2)
M4x6 Flat Head
Bolt
S-F (x4)
M4x6 Bolt
I(x1)
Power Cable
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
J (x1)
Control
Panel
S-G (x3)
Cable Clip
S-H (x10)
Anti-Vibration
Pad
S-I (x1)
Allen Wrench

3
TOOLS NEEDED
275lbs
(124.74kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
STEP 2
Place the side brackets (B) upside down on a flat surface, then place telescopic crossbar (A) over the
brackets as shown, making sure the screw posts on the brackets fit into the holes in the crossbar (A).
Phillips
Screwdriver
Level Drill
Loosen the eight screws on the crossbar using
the Allen wrench (S-I).
STEP 3
Place the crossbar with brackets on the desktop. Adjust the length to suit the desktop.

4
STEP 6
Attach the legs (E) to the assembled frame
using M6x10 bolts (S-A). Tighten with the
Allen wrench. NOTE: Insert all necessary
screws into holes before completely
tightening.
STEP 5
STEP 4
Tighten all screws with the Allen wrench (S-I) to
secure length.
STEP 7
Place the feet (C) on the legs as
shown. Insert the M6x16 bolts (S-B)
as shown and tighten with the Allen
wrench (S-I).
Drill 3/8" (10mm) deep pilot holes under
the desktop with a 3/32" (or 3mm) drill
bit, then remove the crossbar with
brackets.

5
STEP 8
Attach the fixing plate (F) to the crossbar using M4x6 flat head bolts (S-E) with a Phillips screwdriver.
STEP 9
Connect motor cables, control panel (J) and power cable (I)
to the control unit (G).
STEP 10
Slide the control unit onto the fixing plate as shown.