Vivo DESK-E1L94B User manual

Black 47" x 47" Corner Electric Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-e1l94b
SKU: DESK-E1L94B
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
S-A (x43)
M5x16mm Screw
S-B x6)
M6x12mm Screw
S-C (x4)
M5x12mm Screw
S-D (x4)
M8x47mm Screw
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE
FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE
DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT
WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
NOTE: Some hardware may not be used
T-A (x1)
2mm Allen Wrench
I (x1)
Shelf
T x20)
Anti-Vibration Pad
U(x2)
Cable Clip
C(x1)
Right Panel
D (x1)
Sync Rod
G x1)
Right Crossbar
F(x1)
Le Crossbar
K(x1)
Le Leg
H(x1)
Crossbar Connector
L (x1)
Le Side Bracket
B (x1)
Middle Panel
E (x4)
Connecting Plate
M (x1)
Right Side Bracket
J (x1)
Right Leg
T-B (x1)
4mm Allen Wrench
S-E (x8)
M6x35mm Screw
S-H (x2)
Washers
N (x1)
AC Adapter
O (x1)
Control Panel
P (x1)
Motor
Q (x1)
Hook
R (x2)
Foot Extension
S (x2)
Foot
V (x2)
Cable Management
Cover
W (x4)
Foot Pad
A (x1)
Le Panel
S-F (x6)
M6x10mm Screw
S-G (x2)
M8x12mm Screw
T-C (x1)
5mm Allen Wrench

3
176lbs
(80kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Assemble Le Crossbar (F) to Le Leg (K) and Right Crossbar (G) to Right Leg (J) using M8x47mm
Screws (S-D) and 5mm Allen Wrench (T-C). Secure Motor (P) to Right Leg (J) using M5x12mm Screws
(S-C) and 4mm Allen Wrench (T-B).
Drill
STEP 2
Mount Le Side Bracket (L) to Le Leg (K) and Right Side Bracket (M) to Right Leg (J) using M6x10mm
Screws (S-F) and 4mm Allen Wrench (T-B).
F
K
G
JS-D
T-C
PS-C
T-B
L
K
M
J
S-F
T-B

4
STEP 3
STEP 4
Assemble Le Crossbar (F) and Right Crossbar (G) with Crossbar Connector (H) using M6x12mm Screws
(S-B) and 4mm Allen Wrench (T-B).
Secure Feet (S) to the frame assembly using M6x35mm Screws (S-E) and 5mm Allen Wrench (T-C). Screw
Foot Pads (W) into Feet (S). For added stability, Foot Extensions (R) can be added to the back of Feet (S)
with M8x12 Screws (S-G) and Washers (S-H). Tighten using 5mm Allen Wrench (T-C).
F
G
H
S-B
T-B
S
S-E
T-C T-C
W
R
S-G
S-H

5
STEP 5
Insert Anti-Vibration Pads (T) to the frame assembly. Loosen the nut on Sync Rod (D) and insert the hex
rod end into Le Leg (K). While holding the hex end, pull the larger rod out until the connector engages
with Right Leg (J). Tighten the set screw on Sync Rod (D) using 2mm Allen Wrench (T-A), then tighten
the nut.
STEP 6
Place Le Panel (A), Middle Panel (B) and Right Panel (C) upside down on a flat surface. Mount
Connecting Plates (E) with M5x16 Screws (S-A) and a Phillips screwdriver.
T
D
K
J
T-A
A
B
C
E
S-A
1
2
3

6
STEP 7
STEP 8
Connect AC Adapter (N) and Control Panel (O) to Motor (P). Secure Control Panel (O) to the desktop
using M5x16mm Screws (S-A) and a Phillips screwdriver, then organize cables using Cable Clips (U).
Plug AC Adapter (N) into a wall outlet.
Secure the frame along with Hook (Q) and the brackets from Shelf (I) to the desktop assembly using
M5x16mm Screws (S-A) and a Phillips screwdriver.
Q
S-A
I
N
O
P
S-A
U

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.
Insert Cable Management Covers (V) into the desktop. Connect Shelf (I) to the brackets. Refer to the
controller manual for operation.
STEP 9
V
I

LAST UPDATED: 04/27/2022
REV5
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303