Vivo DESK-AC07U User manual

Curved Desk Corner Connector
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-ac07u
SKU: DESK-AC07U
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
inappropriate use.
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
S-A (x12)
M6 Spacer
S-B (x4)
M5x35mm Screw
S-D (x2)
M6x8mm Screw
S-E (x6)
M5 Washer
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
Tape Measure Drill
S-C (x3)
M5x8mm Screw
Phillips
Screwdriver
A (x1)
Desk Sleeve
Pencil

3
ASSEMBLY STEPS
STEP 1
Place Desk Sleeve (A) onto the desktop at the desired location. Measure the space between
the underside of the desktop and the lower portion of the sleeve to determine the required
Spacers (S-A) and Washers (S-E) for mounting. Remove Desk Sleeve (A) from the desktop.
STEP 2
Begin by installing your keyboard
mount (not provided) to Desk Sleeve
(A). Depending on the mount being
installed, use M5x8mm Screws (S-C) or
M6x8mm Screws (S-D) to secure mount
to Desk Sleeve (A). Tighten with a Phillips
screwdriver.
STEP 3
Fit Desk Sleeve (A) with installed
keyboard mount to the desktop. Use
Desk Sleeve (A) and a pencil to mark
drilling locations. Drill 10mm (.4”) deep
pilot holes in the desktop for Curved
Desk Sleeve and the rear end of the
keyboard mount using a 3mm (1/8”) drill
bit.
STEP 4
Secure Desk Sleeve (A) and keyboard mount to the desk using M5x35mm Screws (S-B)
with M6 Spacers (S-A), and M5 Washers (S-E) determined in Step One. Tighten with a
Phillips screwdriver.
DESKTOP
A
A
S-C
S-D
S-A S-E
Note: the quanitity of Spacers & Washers needed is determined by the gap of space between desktop and bottom of
Sleeve. The use of one Spacer & Washer with each screw above is for visual aide ONLY.
A
A
S-B

LAST UPDATED: 06/14/2022
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303