Vivo DESK-V123EB User manual

Electric Multi Motor Corner Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v123eb
SKU: DESK-V123EB/EW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x3)
Feet
B x3)
Motorized Leg
C(x3)
Side Bracket
D(x1)
Extension
Connector
E(x2)
Outer Crossbar
G(x1)
Crossbar
With Plate
H (x1)
Outer Extension
Crossbar
J x1)
Controller
K(x1)
Control Unit
L(x1)
Power Cable
M(x1)
Short Extension
Cable
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK,
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO
REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
N (x1)
Long Extension
Cable
O (x2)
Tabletop
Connector
P (x18)
Anti-Vibration
Pad
Q (x6)
Cable Clip
R (x6)
Foot Pad
S-A (x26)
M5x16mm
Screw
S-B (x32)
M6x11mm
Screw
S-C (x3)
M8x12mm
Screw
S-D (x5)
M5x16mm
Screw
T-A (x1)
5mm Allen
Wrench
NOTE: Extras of each screw size have been included, desktop not included
( 2-section corner desktop shown only for reference)
F(x3)
Inner
Crossbar
I (x1)
Inner Extension
Crossbar
S-E (x14)
M6x35mm
Screw

3
264lbs
(120kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
STEP 2
TOOLS NEEDED
Phillips
Screwdriver
Drill
Attach Feet (A) to the underside of Motorized Legs (B) using M6x35mm Screws (S-E) and 5mm Allen
Wrench (T-A). Thread Foot Pads (R) into underside of Feet (A).
Connect Outer Crossbar (E) and Inner Crossbar (F) to one Motorized Leg (B) using M6x11mm
Screws (S-B) and 5mm Allen Wrench (T-A).
R
A
B
F
S-B
T-A
E
B
S-E
T-A

4
STEP 3
STEP 4
Connect Inner Crossbar (F) and Crossbar With Plate (G) to another Motorized Leg (B) using M6x11mm
Screws (S-B) and 5mm Allen Wrench (T-A).
Slide crossbars from leg assemblies together. These will be secured in a later step.
Secure Extension Connector (D) to the side of Crossbar With Plate (G) using M8x12mm Screws (S-C)
and 5mm Allen Wrench (T-A).
G
F
S-B
T-A
B
G
D
S-C
T-A

5
STEP 5
Connect Outer Extension Crossbar (H) and Innter Extension Crossbar (I) to Extension Connector (D)
using M6x11mm Screws (S-B) and 5mm Allen Wrench (T-A).
Assemble Inner Crossbar (F) and Outer
Crossbar (E) to remaining Motorized Leg
(B) using M6x11mm Screws (S-B) and
5mm Allen Wrench (T-A).
Slide crossbars of third leg assembly onto the existing assembly to form a corner frame shape.
These will be secured in a later step.
H
I
T-A
S-B
D
F
E
T-A
S-B
B

6
STEP 6
STEP 7
Adjust frame to fit desired desktop size and secure the following crossbars in place using M6x11mm
Screws (S-B) and 5mm Allen Wrench (T-A): Crossbar With Plate (G), Outer Crossbars (E), and Outer
Extension Crossbar (H).
Attach Side Brackets (C) to outside edge of Motorized Legs (B) using M6x11mm Screws (S-B) and
5mm Allen Wrench (T-A).
S-B
E
H
E
G
T-A
B
C
C
C
B
B
S-B
T-A

7
STEP 8
Optional
Attach Anti-Vibration Pads (P) to desktop mounting holes in the side brackets and crossbars.
If needed, use provided Tabletop Connectors (O) and M5x16mm Screws (S-A) to secure desktop
pieces together. Note: Desktop is not provided.
P
S-A
O

8
STEP 9
Place assembled frame upside down on the desktop. Drill 10mm deep pilot holes using a 1/8”
(3mm) drill bit, and secure using M5x16mm Screws (S-A) and a Phillips screwdriver.
Mark screw locations for Controller (J) and Control Unit (K), making sure the controller cable
is able to reach the box, then drill 10mm deep pilot holes using a 1/8” (3mm) drill bit. Mount
Controller (J) and Control Unit (K) using M5x16mm Screws (S-D). Tighten all screws with a Phillips
screwdriver.
1
2
3
S-A
S-D
K
S-D J
1
2
3

9
STEP 10
Connect cables from Controller (J) and Motorized Legs (B) to the Control Unit (K). If needed, use
Extension Cables (M, N) to connect legs. Connect Power Cable (L) to Control Unit (K) and plug into an
AC power outlet. Adjust Foot Pads (R) to sit level if necessary. Add Cable Clips (Q) as needed.
AACC
HHSS
MM22MM33MM11
Q
J
BK
B
L
B

10
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.