Vivo DESK-V201G V201G User manual

   

Instruction Manual
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
 
 !"
phillips screwdriver
Scan the QR code with your mobile device or
follow the link to helpful videos and specifications
related to this product.
- -#$$%% "&'$#"$ %
"(
1. This product is intended for indoor use only.
2. This product should be placed on a flat surface.
3. Wipe off any water, oil, or other liquids to prevent damage.
Regularly check and tighten joints to prevent the product from loosening and shaking.
. Do not fully tighten screws until product is assembled.
6. Use a damp cloth to clean the desktop.
1

)'* #
#  )'*  +'
Attach chair legs (B1) to chair feet
(B2), making sure legs are fully
seated in openings.
Secure feet using 4 medium
screws (A2) and 4 metal lock
washers (A1). Tighten with allen
wrench (A10).
Assemble right side support bar
(B3) to leg using 2 medium
screws (A2) and 2 plastic washers
(A3). The support bar has a large
hole on the left side which will
face inward. Tighten with allen
wrench.
Slide center support bar (B ) into
large hole on right side bar. Slide
left side support bar (B4) onto
center bar, and secure to legs
with 2 medium screws (A2) and 2
plastic washers (A3). Tighten with
allen wrench.
2
#  )'*  
# , "  )-"
Secure seat back using knobs
(A ).
Adjust chair feet to sit level if
needed.
Mount plastic seat bottom (B6)
to assembled chair frame using
4 long plastic thread screws (A4).
Tighten with phillips screwdriver.
Slide plastic seat back (B7) onto
chair frame, aligning upper or
lower holes in seat back with
screw holes in frame depending
on the needed height.

# . /"0
Assemble desktop to legs
using 4 long screws (A8) and 4
plastic washers (A3). Tighten
with allen wrench.
# 1 2 
Squeeze sides of hook (A9) and fit
into slot on left or right side of
desk.
Adjust desk feet to sit level if
needed.
# 3 2 4
# . )'*  +'
Assemble right side drawer
slider (B9) to desktop (B8) using
2 short screws (A6) and 2 plastic
washers (A3). Tighten with allen
wrench. Check to ensure slider
pulls out towards the front of
the desk.
Assemble left side drawer slider
(B10) to desktop using 2 short
screws (A6) and 2 plastic
washers (A3). Tighten with allen
wrench.
Attach desk legs (B12) to desk
feet (B13), making sure legs are
fully seated in openings.
Mount plastic drawer (B11) to
sliders using 4 short plastic
thread screws (A7). Tighten with
screwdriver.
Secure feet using 4 medium
screws (A2) and 4 metal lock
washers (A1). Tighten with allen
wrench.
3

4
If you do not understand these directions, or if you have
any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are
no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual.
We cannot be liable for damage or injury caused by
incorrect assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please
contact us. We are happy to replace parts to ensure you
have a fully functional product.
5 6
 " 
Last updated: 4/26/2018
Online Version
 )-"'
Step on the support bar with one foot and pull up with even motion on
both sides of the desk, until it reaches desired height. Repeat with chair.
Loosen knobs on sides of desk
to adjust desk tilt angle, and
tighten knobs to secure position.
# 7  )-"'
Adjust desk feet to sit level if
needed.

Step on the support bar with one foot and pull up with even motion on
both sides of the desk, until it reaches max height. Slowly lower down to
desired height. Repeat with chair.
84