Vivo DESK-V123EW User manual

White Electric Multi Motor Corner Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v123ew
SKU: DESK-V123EW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Allen Wrench
(4mm and 5mm)
B x22)
M6x12
C(x20)
M6x12 Flat Head
D(x2)
M8x12
E(x30)
M5x16
F(x8)
Cable Clip
G (x5)
Foot Pad
1 x3)
Side Bracket
2(x2)
Side Leg
3(x2)
Feet
4(x1)
Center Leg
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
5 (x3)
Inner Crossbar
6 x2)
Outer Crossbar
7(x1)
Center Crossbar
8(x1)
Outer Extension
Crossbar
9(x1)
Inner Extension
Crossbar
10 (x1)
Extension
Connector
11 (x1)
Power Cord
12 (x1)
Control Unit
13 (x1)
Controller
14 (x3)
Extension
Cable
15 (x2)
Connecting
Plate
NOTE: x2 extras of each screw size have been included,
desktop not included ( 2-section corner desktop shown only
for reference)

3
264lbs
(120kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Drill
Attach a side bracket (1) to the short end of each
leg (2, 4) using x2 M6x12 flat head bolts (C) for
each. Tighten with the 4mm Allen wrench (A).
STEP 2
Assemble an outer crossbar (5) and inner
crossbar (6) to each side leg (2) using x2 M6x12
flat head bolts (C) for each crossbar. Tighten with
the 4mm Allen wrench (A). With all legs upside
down and side brackets (1) facing away, the
outer crossbars will be on the le, and the inner
crossbars on the right.

4
STEP 3
STEP 4
Mount the feet (3) to the side legs (2) using x4 M6x12 bolts (B) for each and tighten with the 4mm Allen
wrench (A). Screw x4 foot pads (G) into the feet.
Mount the center crossbar (7) and an inner crossbar (5) to the center leg (4) using x2 M6x12 flat
head bolts (C) for each crossbar, and tighten with the 4mm Allen wrench (A). Screw the foot pad (G)
into the leg, then mount the extension connector (10) to the center crossbar using M8x12 bolts (D)
and tighten with the 5mm Allen wrench (A). With the leg upside down and side bracket (1) facing
away, the center crossbar will be on the le, the inner crossbar on the right, and the open area of the
extension connector facing down.

5
STEP 5
Slide the center leg crossbars together to the crossbars of an outer leg. Flip the assembly right side
up, and assemble the outer extension crossbar (8) and inner extension crossbar (9) to the extension
connector (10) using x2 M6x12 bolts (B) for each crossbar and tighten with the 4mm Allen wrench (A).
With the center leg to the right, the inner crossbar will be on the le and the outer crossbar on the
right. Slide the other side leg assembly together to the extension crossbars. Adjust the frame size to fit
the desktop, and tighten x8 M6x12 bolts (B) into the underside of the outer crossbars using the 4mm
Allen wrench (A) to secure.

6
STEP 6
STEP 7
Place the desktop on the assembled frame. Drill 10mm deep pilot holes using a 1/8” (3mm) drill bit, and
secure using x16 M5x16 screws (E). If using a 2-section desktop, secure sections using the connecting
plates (15) with x8 M5x16 screws (E). Tighten all screws with a Phillips screwdriver.
Mark screw locations for the control unit (12) and controller (14), making sure the controller cable is
able to reach the control unit, drill 10mm deep pilot holes using a 1/8” (3mm) drill bit, and mount the
control unit and controller using x4 M5x16 screws (E). Tighten all screws with a Phillips screwdriver.
Connect the controller and legs (2, 4) to the control unit (12). If needed, use the extension cables (14)
to connect the legs. Connect the power cable (11) to the control unit and plug into an AC power outlet.
Adjust foot pads (G) to sit level if necessary. Refer to Controller User Guide for operational instructions.

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.

LAST UPDATED: 08/27/2020
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303