Vivo DESK-EXT24/W User manual

Clamp-On 24” x 12”
Desk Extension
Instruction Manual
SKU: DESK-EXT24/W
Assembly Video & Product Info
www.vivo-us.com/products/desk-ext24

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please
contact our product support team at 309-278-5303 or [email protected]om for further assistance. Check carefully to
make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not
use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We
cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
LBS
CAUTION!
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.
We’re Here for You
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Chat Us:
www.vivo-us.com
Give us a Call:
309-278-5303
Email Us:
[email protected]om AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
AVG. RESOLUTION TIME (within oice hrs): 5M 4S

3
Phillips
Screwdriver
Package Contents
Included Hardware & Tools
Tools Needed: Weight Capacity:
A (x1)
Right Board
E (x2)
Clamp
B (x1)
Le Board
C (x2)
Support Bracket
D (x2)
Folding Bracket
S-B (x6)
M5x12mm Screw
S-A (x8)
ST5.5x13mm Screw
S-C (x4)
M6x6mm Screw
44lbs
(20kg)

4
ASSEMBLY STEPS
STEP 1
STEP 2
S-A (x8)
Connect Right Board (A) and Le Board (B) together using Support Bracket (C), ST5.5x13mm Screws (S-A)
and a Phillips screwdriver.
S-A
C
A
B
Push Boards towards each other
while tightening screws to prevent
a gap forming in the seam
Press and hold the release levers on Folding Brackets (D) to li and unfold.
D
Release Lever

5
STEP 3
STEP 4
S-B (x6)
Connect Folding Brackets (D) to board assembly using M5x12mm Screws (S-B) and a Phillips
screwdriver.
S-B
D
DESKTOP THICKNESS 1.26-3.48” (32-88.5mm)
Remove Screws (E1) on the back of Clamp (E) and separate Clamp into Upper Clamp (E2) and
Lower Clamp (E3). Use a screwdriver to disassemble Lower Clamp (E2) and flip the Bracket over.
Reassemble the Clamp, as shown below.
E2
E3 E3
Bracket
DESKTOP THICKNESS
LESS THAN 1.83” (<46.5mm)
Please proceed to STEP 5 on next page.
DESKTOP THICKNESS
1.26-3.48” (32-88.5mm)
Follow steps below to adjust Clamp.

6
STEP 5
STEP 6
S-C
E
D
Connect Clamps (E) to Folding Brackets (D) using M6x6mm Screws (S-C) and a Phillips screwdriver.
S-C (x4)
Release Lever
E
D
Secure Clamps (E) to the desktop. Hold release levers on Folding Bracket (D) to raise and lower
extension.

7
[ THIS PAGE INTENIONALLY LEFT BLANK ]

LAST UPDATED: 11/20/23
REV1
v1.0
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
Monday-Friday from 7:00am-7:00pm CST
Need Help? Get In Touch
FOR MORE GREAT VIVO PRODUCTS,
CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM
VIVO-us @vivo_us