Vivo STAND-V003 User manual

Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V003

2 3
ASSEMBLY STEPS
PACKAGE CONTENTS
TOOLS NEEDED
Phillips
Screwdriver
a (x1)
Pole
b(x1)
Clamp
c(x1)
Arm
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
d(x12)
M4x12
e(x12)
M4x30
f (x24)
M4 Washer
g (x12)
M4 Spacer
h (x2)
M8x10
k (x2)
Spare Plastic
Cover
l (x1)
Wrench
Install clamp (b) to pole (a) using M10x15 bolts (i) and tighten with 6mm Allen key (j). The height of
the clamp (b) can be secured at three dierent positions depending on the thickness of your desktop.
i(x2)
M10x15
j(x1)
Allen Key
STEP 1
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM

4 5
STEP 2
Carefully slide arm assembly (c) onto pole (a), making sure the cable clips are facing down. Secure
with M8x10 bolts (h) using a Phillips screwdriver.
STEP 3
OPTION A: Flat Back Monitor
Use M4x12 thumb screws (d) with washers (f) to mount at back monitors. Thumb screws only need to
be nger-tight.
OPTION B: Curved Back Monitor
Use M4x30 screws (e) with washers (f) and spacers (g) for curved or recessed back monitors. Do not
over-tighten.

6 7
STEP 4 STEP 5
To adjust the tilt joints, remove the plastic cover from the side of the joint and turn the nut using the
wrench (l). To adjust the independent center monitor height, turn the bolt on top using the 5mm Allen
wrench (j). Counter-clockwise will lower the monitor, and clockwise will raise the monitor.
Manage cables for side monitors using the cable clips. Cables can also be hidden inside the pole. To
adjust swivel joints, remove the plastic cover, then use the 6mm Allen key (j) to turn the bolt.

Last Updated: 11/30/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654