Vivo STAND-SP03C User manual

Speaker Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sp03c
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-SP03C

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
WARNING!
TOOLS NEEDED
Phillips
Screwdriver
A (x2)
Base
B(x2)
Pole
C(x6)
M6x14
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualied technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specied in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
D (x4)
M6x15
E(x2)
1/4”x1/2”
F (x8)
Rubber Pad
G (x2)
Washer
H (x2)
PLAY:3 Horizontal
Bracket
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
I (x2)
PLAY:3 Vertical
Bracket
Mount Pole (B) to base (A) with M6x14 bolts
(C), and tighten with Allen wrench (L). Apply
pads (F) to bottom of base.
J (x2)
PLAY:1 Bracket
K (x2)
Cover
L (x1)
Allen Wrench
B
A
F
C
L
STEP 2
2A Slide cover (K) to pole and base. To install
Sonos PLAY:3 speaker vertically, mount
vertical support bracket (H) to pole with
bolts (D), and tighten with Allen wrench (L).
Mount Sonos PLAY:3 speaker to stand using
screw (E) and washer (G). Route power cable
through pole.
2B Slide cover (K) to pole and base. To install Sonos
PLAY:3 speaker horizontally, mount horizontal
support bracket (I) to pole with bolts (D), and
tighten with Allen wrench (L). Mount Sonos PLAY:3
speaker to stand using screw (E) and washer (G).
Route power cable through pole. with Allen wrench
(L). Mount Sonos PLAY:3 speaker to stand using
screw (E) and washer (G). Route power cable
through pole.
2C Slide cover (K) to pole and base. To install
Sonos PLAY:1 speaker, mount support bracket
(J) to pole with bolts (D), and tighten with Allen
Wrench (L). Mount Sonos PLAY:1 speaker to stand
using screw (E) and washer (G). Route power
cable through pole.
I
L
D
K
G
E
H
D
K
E
G
J
E
G
K
D

Last Updated: 11/28/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654