Vivo STAND-V002O User manual

Mechanical Arm Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002o
SKU: STAND-V002O
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
A (x2)
Lower Arm
B(x2)
Upper Arm
C(x1)
Base
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x2)
VESA Plate
E(x1)
Upper Clamp
F (x1)
Lower Clamp
G (x1)
Grommet Plate
H (x1)
Knob
S-B (x2)
M6x10mm Screw
S-C (x2)
M8x30mm Screw
M-C (x8)
M5 Washer
T-A (x1)
4mm Allen Wrench
M-A (x8)
M4x12mm Screw
S-A (x2)
M6x8mm Screw
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
4.4-19.8lbs
(2-9kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
T-B (x1)
5mm Allen Wrench
M-B (x8)
M5x12mm Screw

3
ASSEMBLY STEPS
STEP 1 (Option A)
Clamp Installation
Remove plastic shroud from Base (C). Adjust the knob completely down on Lower Clamp (F).
OROR
For 0.4”-1.90” (10-50mm) desktops install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A)
and 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C). Attach Lower Clamp (F) to the
top two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A). Secure
clamp assembly to the desktop.
For 1.8”-3.1” (45-80mm) desktops install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and
5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C). Attach Lower Clamp (F) to the
bottom two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A).
Secure clamp assembly to the desktop.
C
F
E
C
S-A
T-B
S-B
T-A F
E
C
S-A
T-B
S-B
T-A F

4
STEP 1 (Option B)
STEP 2
Grommet Installation
Mark two drilling locations 2” (51mm) apart in desired location. Drill grommet holes using a ⅜” (10mm)
drill bit drilling completely through the desktop. Disassemble Lower Clamp (F) using the Phillips end
on 5mm Allen Wrench (T-B). Place Grommet Plate (G) on Knobs (F1,H) and secure assembly to the
desktop.
Place Lower Arms (A) onto Base (C) and Upper Arms (B) onto Lower Arms (A). Tighten set screws using
the flathead end on 4mm Allen Wrench (T-A).
F
T-B
F1
F1 H
G
A
C
B
T-A

5
STEP 3
STEP 4
Attach VESA Plates (D) to Upper Arms (B) using M8x30mm Screws (S-C) and 5mm Allen Wrench (T-B).
Install two Screws (M-A or M-B) and M5 Washers (M-C) using the Phillips end on 5mm Allen Wrench
(T-B) to the top VESA holes on the monitor leaving at least 3mm of clearance between the screw and
monitor. Slide the monitor onto VESA Plate (D) making sure the screws sit within the slots.
D
B
S-C
T-B
T-B
D

6
STEP 5
Tighten the top two screws and install the remaining Screws (M-A or M-B) and 5mm Washers (M-C)
using the Phillips end on 5mm Allen Wrench (T-B).
STEP 6
T-B

7
STEP 7
STEP 5
Remove bottom plastic covers from Lower Arm (A) using the Phillips end of 5mm Allen Wrench (T-B).
Slide plasic covers o of Upper Arms (B). Run cables from monitors through bottom of Upper Arms (A)
and Lower Arms (B), then reattach plastic covers.
Adjust monitor tilt support using 5mm Allen Wrench (T-B) as shown. Adjust monitor position as desired.
A
B
T-B
T-B

LAST UPDATED: 09/15/2023
REV3
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303