Vivo STAND-V149 User manual

Single Ultrawide Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v149
SKU: STAND-V149
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
TOOLS NEEDED
33lbs
(15kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please contact our product support team at 309-278-5303 or [email protected]om for
further assistance. Check carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for any purpose that is not
explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
PACKAGE CONTENTS
A (x1)
Pole
B (x1)
Clamp
C (x1)
Swivel Arm
T-A (x1)
3mm Allen Wrench
T-B (x1)
6mm Allen Wrench
T-C (x1)
Long 6mm Allen Wrench
G (x1)
Pole Cable Clip
I (x1)
Plastic Cover
J (x1)
Support Plate
F (x2)
Cable Clip
D (x1)
VESA Plate
E (x1)
Pole Cap
S-A (x1)
M6 Security Nut
S-B (x1)
M10x90mm Screw
H (x1)
Grommet Plate
M-C (x4)
Spacer
M-B (x4)
M4x30mm Screw
M-A (x4)
M4x12mm Thumbscrew
K (x5)
So Pad

4 5
Option B: Grommet Install
If desk does not have an existing grommet hole, drill a 3/8”
(10mm) diameter hole at the desired position through the
mounting surface.
Tightly thread Pole (A) onto Grommet Plate (H) and ensure a snug connection between both parts.
Tighten the set screws in Grommet Plate (H) using 3mm Allen Wrench (T-A) and then slide Plastic
Cover (I) over Grommet Plate (H) pressing firmly in place.
STEP 1b
K
H
Attach So Pads (K) to under side of Grommet Plate (H). Secure Grommet Plate (H) to the desktop
using M10x90mm Screw (S-B) with Support Plate (J) and 6mm Allen Wrench (T-C).
H
J
T-C
S-B
T-A
A
I
H
ASSEMBLY STEPS
STEP 1a
OPTION A: Desk Clamp Install
Mount Clamp (B) to the desktop and tighten using the plastic knob.
Tightly thread Pole (A) onto Clamp (B) to ensure a snug connection between these two parts.
Tighten the set screws in Clamp (B) using 3mm Allen Wrench (T-A) and then slide the Plastic
Cover (I) down over Clamp (B) pressing firmly in place.
B
A
I
T-A
B
Proceed to
Step 2 on Page 6 Proceed to
Step 2 on Page 6

6 7
Attach Cable Clips (F) onto each segment of Swivel Arm (C).
STEP 3
STEP 4
F
C
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the monitor with M4x12mm Thumbscrews (M-A).
NOTE: Hand tighten screws to avoid over tightening.
D
OPTION B: Recessed Back Monitor
Attach the VESA Plate (D) to the monitor with M4x30mm Screws (M-B) and Spacers (M-C).
NOTE: Gently tighten using a screwdriver
D
Slide Pole Cable Clip (G) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm (C) at desired height
using 6mm Allen Wrench (T-B). Insert Pole Cap (E) into top of Pole (A).
STEP 2
G
C
A
T-B
E

8 9
STEP 6a
Manage cables using Cable Clips (F) and Pole Cable Clip (G).
” TO ” MONITORS
The tilt-joint has been pre-tightened and larger monitors may tilt upward when mounted. Slowly
adjust the monitor angle downward by hand until it is at your desired angle.
Note: Some monitors over 40” may be too
light to adjust without loosening the tilt-joint
first. If you are having diiculty adjusting
your monitor please refer to STEP 6b.
If you go past your desired angle and want to adjust the monitor angle upward, use Long 6mm Allen
Wrench (T-C) to loosen the tilt-joint then adjust monitor to desired angle and retighten the tilt-joint.
F
G
Large monitors can be very diicult to adjust by yourself.
Please use caution and have someone assist you with
adjusting your monitor to avoid possible damage or injury.
WARNING
T-C
PLEASE FOLLOW THESE STEPS FOR ALL
FUTURE ADJUSTMENTS TO PREVENT
POSSUBLE DAMAGE OR INJURY.
Slide VESA Plate (D) with monitor onto the head of Swivel Arm (C). Install M6 Security Nut (S-A).
NOTE: Ensure the security nut is installed before you rotate the monitor.
STEP 5
Large monitors can be very diicult to mount by yourself. Please use
caution and have someone assist you with mounting and adjusting
your monitor to avoid possible damage or injury.
WARNING
D
C
S-A

10 11
Further Adjustments
Adjust monitor as desired. For 40” to 49” monitors, please follow instruction in Step 6a
for tilt adjustments.
Large monitors can be very diicult to adjust by yourself.
Please use caution and have someone assist you with
adjusting your monitor to avoid possible damage or injury.
WARNING
STEP 6b
Use long 6mm Allen Wrench (T-C) to loosen the tilt-joint then adjust monitor to desired angle. Once
fully adjusted, retighten the tilt-joint.
NOTE: Two people may still be necessary for installing and adjusting the monitor depending on
your unique screen and mounting configuration.
T-C
” TO ” MONITORS
PLEASE FOLLOW THESE STEPS FOR ALL FUTURE ADJUSTMENTS TO PREVENT
POSSUBLE DAMAGE OR INJURY.
+90° to -90° Tilt 360° Swivel
360° Rotation

LAST UPDATED: 08/03/2023
REV1.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303