Vivo STAND-V003P User manual

Triple Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003p
SKU: STAND-V003P
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B(x1)
Pole
C(x1)
Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x2)
Side VESA
Bracket
F (x6)
Cable Clip
G (x1)
Cable Clip
H (x1)
Pole Cover
I (x4)
Bushing
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x12)
M4x12
M-B (x12)
M5x12
J (x2)
M8x60
L(x2)
M8 Nut
M-C (x12)
D5 Washer
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
E(x1)
Center VESA
Bracket
K (x4)
D8 Washer
M(x1)
3mm Allen
Wrench
N(x1)
5mm Allen
Wrench
O(x1)
6mm Allen
Wrench
P(x1)
Wrench

3
ASSEMBLY STEPS
TOOLS NEEDED
Phillips
Screwdriver
STEP 1
Slide cable management clip (G) and base cover (H) on to bottom of pole (B). Thread pole (B) into
base (A), first loosening grub screws in the base if needed. Tighten grub screws using 3mm Allen
wrench (M).
STEP 2
17.6lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
Place bushings (I) into holes at ends of arms (C).
Place side VESA brackets (D) onto arms with M8x60
bolts (J) and two D8 washer (K). Secure with two
D8 washers (K) and M8 nuts (L), and tighten with
5mm Allen wrench (N) and wrench (P). Do not
overtighten.

4
STEP 3
Slide arm (C) and center VESA bracket (E) over top of pole and tighten using 5mm Allen wrench (N).

5
STEP 4
Attach cable management clips (F) to arms (C) as shown.
STEP 5
Attach two bolts (M-A or M-B) and washers (M-C) to top mounting holes of monitor, making
sure to leave 3mm of threads exposed.

6
STEP 5 (Continued)
Align bolts (M-A or M-B) in monitor over slots in VESA plates.
Secure using two more bolts (M-A or M-B) and washers (M-C)
in the bottom two holes of each monitor. Tighten all bolts using
Phillips screwdriver.
STEP 6
Adjust tension in monitor bracket with 6mm
Allen wrench (O).
STEP 7
Store Allen wrenches (N, O) in cable management clip (G) for future use.

7
STEP 8
WARNING: Do not move monitors behind center line. Stand can become unbalanced and cause
monitors to tip.
STEP 9
Adjust height of side monitors by turning bolt on top of each bracket with 5mm Allen wrench (N)
as shown.

LAST UPDATED: 06/03/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303