Vivo STAND V001L User manual

Laptop Tra  Des Mount
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model STAND V001L
A 



 
 
D
 
E 
 
F 
 


J 
 

  !
!"
#" 
I 
 
L 
$%  !
M 
&  

N1 
 
O 
$ '(
$
$!
R 
 
S
 
N& "
 
Scan the QR code with your mobile device or follow the link to
helpful videos and specifications related to this product.
Tools Required
phillips screwdriver
$acage ontents
1
- -https//vivo us.com/products/stand v001l
Q 
- " )!* 
U 
 
T 
+ )(
V 
 
-2 1 
, -
- 2 & 
, -

Assembl Steps
2
Step 1 Install the $ole to the Destop
1. Install the Clamp Brace (C) to the Pole (A) using 3pcs Bolts (F), see Figure 1.
2. Attach Soft Pad (W-1) to the Clamp Brace (C), see Figure 2.
3. Install the Clamp (B) to the pole assembly according to the thickness of the desktop.
The thickness can be changed to three positions. Connect it using 2pcs Bolts (G), and
tighten using the Allen Key (O). Tighten the Clamp to the desktop using the plastic
knob, see Figure 3.
Option A Des lamp Install
Existing Grommet Hole Installation
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate (M) to the
Pole (A) using 3pcs Bolts (F), see
Figure 4.
2. Attach Soft Pad (W-2) to the Grommet
Base Plate (M), see Figure .
3. Position the Pole (A) on the mounting
surface and secure using the Support Plate
(J), M10 Washer (K), Spring Washer (L) and
M10 Bolt (I). Fasten the M10 Bolt using
provided Wrench (P), see Figure 6.
Figure 1 Figure & Figure 3
Figure 4 Figure 5
Figure 6
Option  !rommet ase Install
Step 1 (ontinued)
Step & Install Arm to the $ole
Option  !rommet ase Install
Self Drilled Grommet Hole Installation
1. Position the Pole (A) on the mounting
surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked
position through the mounting surface.
2. Install the Grommet Base Plate (M) to the
Pole (A) using 3pcs Bolts (F), see Figure 7.
3. Attach Soft Pad (W-2) to the Grommet
Base Plate (M), see Figure 8.
4. Position the Pole (A) on the mounting
surface and secure using the Support Plate
(J), M10 Washer (K), Spring Washer (L) and
M10 Bolt (I). Fasten the M10 Bolt using
provided Wrench (P), see Figure 9.
Install Swivel Arm (D) to the Pole (A). Fasten the bolt with supplied Allen Key (O).
Attach the Wire Clip (N1,N2) to the Pole (A) and Swivel Arm (D).
Figure 7 Figure 8
Figure 9

Step 5 Mae adjustments
Tighten the bolt with the supplied Allen
Key (O) to fix the tilt angle.
Use the supplied Allen Key (O) to make
the necessary adjustments.
Step 4 Attach Monitor to Swivel Arm
Slide the monitor onto the head of
Swivel Arm (D) as shown in the above
diagram.
Install the Security Nut (H). Make sure
the Security Nut is installed before
you rotate the monitor.
Step 3 Attach VESA $late to Laptop Tra or Monitor
For Laptop For Monitor
with a Flat ac
For Monitor
with a urved or
Recessed ac
3

4
If you do not understand these directions, or if you have
any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are
no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual.
We cannot be liable for damage or injury caused by
incorrect assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please
contact us. We are happy to replace parts to ensure you
have a fully functional product.
Safet 2arning
ontact us at
Last updated: 4/30/2018
Step 6 Manage ables
Use wire clips (N1, N2) to manage cables. Store Allen Keys (O) in wire clip
(N1) for future adjustments.