Vivo STAND V004M User manual

Quad Monitor Desk Mount
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model: STAND V004M
Tools Required:
phillips screwdriver
Package Contents
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
A (x2)
Arms
B (x1)
Lower Pole
C (x1)
Upper Pole
D (x1)
“ C” Clamp
E (x1)
Grommet Plate
(x1)
Pole Connector
G (x2)
Cable Clip
H (x1)
Plastic Cover
I (x5)
Rubber Pa
J (x1)
Support Plate
K (x1)
3mm Allen
Wrench
L (x1)
5mm Allen
Wrench
M (x1)
6mm Allen
Wrench
- -https://vivo us.com/products/stand v004m
-M C (x16)
D5 Washer
-M A (x16)
M4x12 Screw
- M B (x16)
M5x12 Screw

Assembly Steps
2
Step 1
Option A: “C” Clamp Installation
Slide one cable management clip (G) and base cover (H) onto
bottom of pole (B). Thread pole (B) onto clamp (D). Tighten grub
screws in bottom of clamp (D) using 3mm allen wrench (K). Secure
clamp (D) to desktop as shown in diagram.
Option B: Grommet Base Installation
Remove screw from top
of bolt in clamp (D).
Stick rubber pads (I)
to bottom of
grommet plate (E).
Slide cable
management clip (G)
and base cover (H) onto
bottom of pole (B).
Thread pole (B) onto
grommet plate (E).
Tighten grub screws in
bottom of grommet
plate (E) using 3mm
allen wrench (K). Slide
support plate (J) over
bolt and slide through
grommet hole in
bottom of desktop.
Thread into bottom of
pole (B).
Step 2
Adjust height of stopper using 3mm allen wrench (K).
Step 3
Slide arm (A) onto pole (B). Tighten using mm allen wrench (L).
10-80mm

Step 6
Insert screws (M-A or M-B)
and washers (M-C) into top
two holes on monitors.
Leave slightly loosened.
Slide monitors onto VESA
plates and insert screws (M-
A or M-B) and washers (M-
C) into bottom two holes on
monitors. Tighten all
screws.
Step 7
Adjust the tilt angle
of the monitors. If
the weight of the
monitors is not
supported, tighten
joints with 6mm
allen wrench (M) as
shown in diagram.
Step 4
Screw on pole adapter (F) by hand. Slide one cable management clip
(G) onto pole (C). Thread pole (C) into pole adapter (F). Tighten grub
screws on pole adapter (F) using 3mm allen wrench (K). Adjust height
of stopper using 3mm allen wrench (K).
Step 5
Slide arm (A) onto pole (C). Tighten using mm allen wrench (L).
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
Safety Warning
Contact us at:
Last updated: 0 /23/18
Step 8
Store allen wrenches (K, L, M) as shown in diagram.
Step 9
If monitor heights are not aligned, turn
the screw behind each VESA plate using
the mm allen wrench (L). Clockwise will
raise the monitor and counter-clockwise
will lower the monitor.
4