Vjoycar C61 User manual

C61 USER GUIDE
Feature:
Head-up display - projects the driving speed on the windscreen.
GPS Data logger. GPS Data will be saved into SD automatically. No SIM needed
Driving time and mileage calculation and display
Easy Setup--Plug & Play- Power through vehicle cigarette lighter. No professional installation is required.
Compatible with all Cars & Trucks. Use GPS signal guided calculation. No wiring needed to the VSS (vehicle speed signal).
Display MPH or KM/h
Auto adjust brightness through sensor for Day & Night driving.
Vehicle driving speed display. Green color speed display, easy on your eye.
Over-speed Alarm setting
Product Image:
Content of the packaging:
1. GPS HUD speedometer
2. USB Cable
3. Reflecting Sticker
4. Anti-slip Pad
5. User Guide
6. Packing Box
Operation Guide:
1. Set the over-speed alarm rate
A: Press the Up Button or Down Button to increase or decrease the speed rate
B: The default alarm speed rate is 120KM/h
2. Set display mode: Press Enter button, you will see numbers “111” “222” “333” are shown on the screen：
A: 111 refers to Normal display mode, content will be shown on the screen in normal condition.
B: 222 refer to Reflecting display mode, content will be shown on the screen in opposite side in order to be reflected on
the windscreen correctly.
C: 333 refer to Upside-down display mode, content will be shown on the screen upside-down in order to fit the specific
position in the car, such as behind the front rearview mirror. (for certain vehicle models only)
3. Set the speed meter unit (KM or Mile)
UP Button
Down Button
Enter Button
USB Charging Slot
Micro SD Card Slot

A: Long press the Enter button, if you see number 100 shown on the screen, which means KM/h
B: Long press the Enter button, if you see number 161 shown on the screen, which means MPH
C: The default speed meter unit is set as KM/h
Driving data record display
1. System will start calculating total driving time and mileage when device is powered on.
2. Parking time is not included in the calculations in order to increase the data accuracy.
3. Mileage less than 1KM will be considered as invalid data
4. Once the vehicle stops for a few seconds, you will see data displayed on the screen in order as total mileage, and then the
total driving time in minutes.
5. All driving data will be cleared once the vehicle is engine off, and system will start the calculation again when the car
power resumed.
SD Logger
SD storage enable device to save all GPS tracking data into the SD card and user can playback history or check data reports on
the website afterwards
Please operate as follows:
a. Insert a Micro SD card into the SD slot and turn the device on.
b. GPS data will be saved into the SD card automatically.
c. Take the SD out of the device when you need to check the saved data.
d. Copy the .txt files from the SD card to your PC.
e. visit http://offline.miitown.com/
f. Select the .txt data file and click Submit to view history playback.
g. Click Report to view saved data report.
Fatigue Driving Alarm
In every hour, system will trigger a fatigue driving alarm with continuous driving time displayed, in order to remind drive to
avoid drowsy-driving.
Example: 001 means one-hour continuous driving, 002 means two-hour continuous driving and so on.
Over Speed Alarm
1. Set the over speed alarm rate (As described in the Operation Guide)
2. A three times “Beep” sound alarm will be triggered when over speed occurs.
3. No more alarm will be triggered when over-speed is detected continuously.
How to paste reflecting sticker
1. Clear the car windshield;
2. Tear the reflecting sticker and paste it on the car windshield;
3. Gently squeezed out the air bubbles;
4. It can be used repeatedly.
Technical Specifications
1. GPS positioning time: 1 to 3 minutes in the open air (The bad weather will affect the positioning time).
There is no GPS signals indoors.
2. Speed deviation: Since the speed data comes from the GPS satellite, slight deviation is unavoidable.
3. Input voltage: DC 5V Input current: DC 50-120mA Power bank for power supply is supported.
4. Working temperature: -30 to 70 degree
5. Driving data deviation is around 2%
6. All driving data will be cleared when power off