Volt Polska GREEN BOOST 3000 User manual

PRODUCT MANUAL
VOLT POLSKA Sp. z o.o.
ul. Swiemirowska 3
81-877 Sopot
www.voltpolska.pl
[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
GREEN BOOST
3000
ECO SOLAR BOOST
FOR HEATING WATER, BOILER

[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
Max constant power 3000W
Max power 6000W
Efficiency > 95%
Output voltage
Output voltage from panels PV 120VDC ~ 350VDC
Max panels power ≤ 4500W
Output voltage waveform
2pcs
Working modes MPPT / STABLE
Displayed LED
Yes
Yes
Yes100±10℃
Cooling Built-in fan
Warning system Sounds and light signals
od -25～+55 ℃
Storage temperature od -20～+45 ℃
Weight 2,7kg
345x215x120mm (with MC4)
TECHNICAL DATA GREEN BOOST 3000
Congratulations on choosing our high-quality eco solar
boost - Green Boost 3000 (DC 1210-350V) for water heating,
boiler, heating floor and others.
Above the output voltage of 250V from the
panels, the inverter offers the output of
approx. 245V!
Connection of PV panels
Output socket
120 ~ 245VAC/ 50Hz
Modified sine wave
Series or series-parallel
Power connector (input)
Overload protection
Short circuit protection
Thermal protection
MC4-2pcs
Operating temperature
Dimensions

[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
INTENDED USE
INSTALLATION
The eco solar boost - Green Boost 3000 (DC 1210-350V) is designed to
power heating devices such as boilers, heaters, electric heaters or heating
mats directly from PV panels.
The system requires: 4 to 9 typical PV panels (250W - 400W) connected in
series, with a total voltage from 120V to 350V.
Our inverter is equipped with internal maximum power protection of 3kW.
However, the total power of the panels connected to the inverter should not
be higher than 5kW.
Green Boost 3000 (DC 1210-350V) allows to connect two heating devices
(e.g. two boilers). One will be heated first and the second one will be heated
only, if the thermostat of the first one stops receiving energy from the
inverter.This ensures that energy from the PV panels will not be lost when
one of the units reaches a set temperature.
Green Boost 3000 (DC 1210-350V) is equipped with MPPT. Thanks to that,
the inverter will automatically adjust to the power of boiler and maximizes
the amount of energy drawn from PV panels.
To connect the PV panels to the inverter, use suitable PV installation cables
with a cross section not less than 4mm. Using wires that are too thin will
cause heating up and a voltage decreasing at the inverter input. In extreme
cases it can cause a fire.
The inverter requires unobstructed air circulation for proper operation. Do
not, under any circumstances, cover the ventilation holes as this may be a
direct cause of overheating and damage of the device.
To improve heat dissipation and for your own safety, we suggest to screw
the inverter vertically to nonflammable surfaces (concrete, metal).

[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
SAFETY
The eco solar boost - Green Boost 3000 (DC 1210-350V) produces a
dangerous voltage at the output that may cause electrical shock or fire.
To avoid that, we suggest to follow all safety rules that apply to electrical
equipment (230V).
Please note, that the high voltage may persist even after disconnecting
the power supply for a quarter of a minute.
Any repairs should only be carried out by an authorised service centre.
Do not put the voltage inverter in a high-humidity area, near a fire source,
flammable substances. Do not also expose it to direct sunlight. If the
device gets wet, immediately disconnect the power supply.
Do not connect a load greater than that permitted for continuous
operation to the inverter output. Overloading may cause damage to the
device.
In case of fire, use a fire extinguisher designed for extinguishing
electrical equipment.
Under no circumstances may the input and output of eco solar boost -
Green Boost 3000 (DC 1210-350V) be connected to the power grid.

CONNECTION
URGENT!
The polarity of the supply voltage is very important while connecting PV
panels to inverter. The reverse wiring will cause damage to the inverter and
void the warranty!
The eco solar boost - Green Boost 3000 (DC 1210-350V) has two MC4
connectors which must be connected to the PV installation. The connector
shaped should be connected to the negative pole of the PV
installation and the connector shaped should be connected to the
positive pole of the PV installation.
ADC safety switch, designed for such installations, shall be installed on the
PV system power cord.
We connect device e.g. an electric boiler to the inverter output marked - "1".
When the inverter detects the presence of voltage from the PV panels within
the appropriate range, the inverter will automatically turn on. This will be
confirmed by the LED indicator.
Optionally, a second energy consumer can be connected to the inverter
output marked "2". This can works only with a bi-metal thermostats.
Electronic temperature controllers can only work with an output “1”. Lack of
activities on both outputs for a long time will cause a delay of load sense on
output up to several minutes.
The eco solar boost inverter Green Boost 3000 (DC 1210-350V is
equipped with two power outputs - type E (labelled "1" and "2)". After
connecting the correct supply voltage from the solar power system (120-
350V ), the inverter checks the presence of connected receivers.
In the case of connecting two resistance receivers, firstly, the device
connected to the socket "1" will be powered. When the device stops
consuming energy, the eco solar boost inverter Green Boost 3000 (DC
1210-350V will switch to power socket "2". However, if the load on socket
"1" will reappear, the inverter it will automatically cut the power supply to
output "2" and start to power outputs "1".
USE

[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
OUTPUT
SECONDARY OUTPUT VOLTAGE SYSTEM
FAULT
OUTPUT
PRIMARY PV CURRENT
A
V
SOLAR
STATUS PV VOLTAGE
OVER
HEAT
VMPPT
MODE
SOLAR STATUS - When the PV voltage is greater than 80% of the rated
voltage of the device, the indicator lamp will be lit. Otherwise, it will blink.
OUTPUT PRIMARY - It lights when socket 1 is working
OUTPUT SECONDARY - It lights when socket 2 is working
PV VOLTAGE - Actual PV input voltage
PV CURRENT - Actual PV input current
OUTPUT VOLTAGE - Output voltage status, shows the actual output
voltage current of the inverter
MPPT MODE - It lights when the MPPT mode is on
OVER HEAT - It lights when the inverter is overheated
SYSTEM FAULT - It lights when the PV voltage is too high or the inverter
does not work properly (continuous light) or warns of overload.

[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
CONNECTING DIAGRAM „1” i „2”
PRIMARY
SECONDARY
(ACTIVE ONLY
WHEN NO LOAD
ON PRIMARY)
-
+
-
+
-
+
+
-
+
-
-
+
2
1
PRIMARY
SECONDARY
MC 4
-
+
-
+

[email protected] (58) 341-05-06 | [e-mail] (58) 341-38-80 | bar[email protected] (22) 100-42-99
WARRANTY SERVICE COMMENTS
DATE OF PURSCHASE
SHIPPING ADDRESS
SIGNATURE / STAMP
DAMAGE DESCRIPTION
SERVICE COMMENTS
PRODUCENT:
VOLT POLSKA Sp. z o.o.
ul. Świemirowska 3
81-877 Sopot
www.voltpolska.pl
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
The marking on the product or in related texts indicates that it is at the end of its useful life should not be disposed of with
other household wastes. To avoid harmful effects on the environment and human health as a result of uncontrolled waste
disposal, please separate the product from another type of waste and responsible recycling to promote the reuse of material
resources as a permanent practice. Users in the households should contact the retailer where they purchased the product, or
with a local authority. Business users should contact their supplier and check the terms of the contract purchase. The product
should not be disposed of with other commercial waste.