VSYSTO F4.5X User manual

- 1 -
MOTORCYCLE DASH CAM
F4.5X USER MANUAL
Shenzhen V-SYS Technology Co.,Ltd.
[e-mail]
https://www.facebook.com/szvsys
https://www.youtube.com/c/szvsys
MENU
OK

- 2 -
This product records videos while the motorcycle is operating. Use this product only for
reference when investigating incidents or road accidents. This product is not guaranteed to
record ALL events. The device may not properly record accidents with small impacts that are
too minor to activate the impact sensor or accidents with massive impacts that cause the
motorcycle’s battery voltage to deviate. Video recording does not begin until the product is
completely turned on (booted up). To ensure that all motorcycle events are recorded, wait until
the product is completely booted up after turning it on, and then begin operating the motorcycle.
VSYSTO is not responsible for any loss caused by an accident, nor is it responsible for
providing any support regarding the outcome of an accident.
Before using the product
During use of the product
Read the following safety information to properly use the product.
• Do not operate the product while driving a motorcycle. Distraction while driving may
cause accidents and result in injury or death.
• Do not install the product in a place exposed to flammable gas. Doing so may result in
fire or an explosion.
• Do not use the product in a place with high humidity or temperature. It may cause
malfunction of the product, explosion, or fire.
• Do not disassemble the product or subject the product to impact. Doing so may
damage the product. Unauthorized disassembly of the product voids the product
warranty.
• Do not fully submerge the product in water. Doing so may damage the product.
• Do not use the product outside for a prolonged period of time when it is raining. Doing
so may cause water damage to the product.
• Do not clean the product with chemicals or detergent. Doing so may damage the
product. Clean the product using a clean, soft, dry fabric.
• Ensure that the memory card is in the correct direction before inserting it into the
product. The memory card slot or the memory card may be damaged if it is inserted
incorrectly.
• Please format cards before use and anytime a significant amount of data has been
collected to ensure that the device and SD cards are working properly together. It is
recommended to format the TF card at least once a week.
• Use the product at a temperature between -20°C to 65°C. The product may not
function as designed and some permanent physical damages may result if it is
operated out of the specified temperature ranges. Such damages are not covered by
the warranty.
•The product emits electromagnetic radiation that might interfere with medical
devices. Consult with your physician and your device manufacturer if you are uncertain
whether you can use this device.
• Please use this product to the extent permitted by law.

- 3 -
Packing List
Connection Diagram
The connection may change without prior notice.
The items may vary for different buying options.
Main unit structure
The product design may change without prior notice.
Handlebar mount
Cam1 & extension cable
Cam2 & extension cable
USB test cable
GPS Tracker
Main Unit
Wired Controller
MENU
OK
MEN U
OK
MEN U
MENU
OK
Mount hole
LCD display
Menu/Back
Move up
Move down/ Display mode switch
OK/REC/Play/Pause
Card slot
Split cable(Power module/GPS)
Wired remote
Cam 1
Cam 2
Power cord

- 4 -
Short press to select the video to playback
R/REC-211019-120514R.MOV
1
1
RearCam
F/REC-211019-175340R.MOV
1
1
2021/10/19 17:53:25 [00:00:26]
“F/” indicates front cam video playback “R/” indicates rear cam video playback
Video recording time
WiFi
Date & time information
Recording
2021/10/19 17:53:25 [00:00:26]
Select the setting options and
press the button to enter
Video Mode.
Select the setting options
and press the button to
enter Playback Mode.
Long press for 3 seconds in the playback mode to switch
the video files list between front camera and rear camera.
Select the setting options and press the
button to enter Setting Mode.
Select the setting options and press the
button to enter Language Settings.
Menu Setting Description
* Press button of remote controller to pause recording before setup the system, then
long press button to enter menu system.
“REC” means normal video file
“GSR” means file recorded by triggering G-sensor
“163256” means time 16 o’clock 32 minutes 56seconds
“MOV” means video file format
“KEY” means file recorded by pressing remote
“170809” means date 9th August, 2017
“F” means front camera video file
Video file name information: REC_170809-163256F.MOV
Short press in video mode to switch
different display mode;
•
•
•
NOTE: The recorder will lock the latest 10 emergency recording videos(GSR-XXXX.MOV) triggered by G-sensor
and 10 emergency recording videos(KEY-XXXX.MOV) manually triggered by the remote from being overwritten,
and after more than 10, the recorder will automatically start to overwrite the earliest locked emergency video.
MENU

Parking monitoring On/Off
Set the impact sensitivity when parking
Movie clip time Set the loop clip time
Sound record
Toggles the microphone on/off
MIC sensitivity Set the sensitivity of the microphone
LCD Power Save Set the screen saver time
Date format YYYY MM DD/MM DD YYYY/DD MM YYYY
Clock settings Set date & time
R-Cam mirror Turn on/off the mirror image of the rear
camera
Protect Level Set the sensitivity of the G-Sensor
Beep Turns the sound on or off for each time a
button is pressed.
Voice guide On/Off
Format SD card Delete all videos from the memory card
WiFi mode On/Off
Reset setup Reset your device to factory settings
FW version Check the firmware version
Movie Off Time Set the recording time of the camera
after the bike is turned off
Parking sensitivity
Time zone select Time zone selection around the world
Speed stamp Turn on/off the speed watermark
when playback videos on the PC/APP
Display the current number of satellites,
longitude, latitude and other information
Unit system Metric units, Imperial units
GPS Status
Menu Setting Description
Tire pressure unit bar/psi
TPMS alarm sound On/Off
TPMS Threshold Set the maximum and minimum tire
pressure alarm value
Operation Guide Introduction to the operation of the
wired remote
Flameout detection On/Off
Parking Mode
Impact Mode
Both front and rear cameras will record 30
seconds when detecting an impact and then
turn it off to keep the energy usage to a
minimum.
• Built-in voltage cut-off protection so your motorbike battery will never be drained out. If the power drops
below 11.8V the camcorder will automatically shut down.
• Menu Settings > Setting Mode > Parking
monitoring (On/Off)
• Menu Settings > Setting Mode > Parking
sensitivity (High/Stardard/Low)
Preset Mode Both front and rear cameras will automatically
record when the engine is off and then turn it
off when reaches the set length of time.
• Menu Settings > Setting Mode > Flameout
detection (On/Off)
• Menu Settings > Setting Mode > Movie Off
Time (15 min/30 min/1H/2H/3H)
(Parking monitoring)
(Flameout detection)
• Impact Mode: Enable
• Preset Mode: Disable
ACC Version
Power Cable
• Impact Mode: Enable
• Preset Mode: Enable
Smart Version
• Impact Mode: Disable
• Preset Mode: Disable
USB Cable
Power Supply Parking Mode Feature Power Triggered by
Key Switch
Voltage change /
Continuous vibration
Key Switch
- 5 -

Click to stop recording manually. Click to start recording manually.
Click to take photo.
Click to switch front and rear camera. Click to enter/exit full screen view.
Click to go back to the previous menu.
When successfully connected with your smartphone via built-in Wi-Fi, you can save
and playback the driving recording videos on your smartphone. You can also change
settings of dash cam via Wi-Fi app.
1) Scan the QR code below to download the latest App from Google Play and App
Store. Or you can search ‘Wifi Camera’ on Google Play or App Store to download it.
2) Select 'MotoDV_XXX' from available Wi-Fi network to connect. The default password
is '1234567890'.
Wi-Fi Connection
3) Wi-Fi app operation
The camera will pause the recording when you open Wi-Fi App (connected
successfully) and Enter recorder during recording, and start recording automatically
after 30 seconds without any operation or 30 seconds after you quit the App. Also,
you can start/stop recording manually via the Wi-Fi App.
- 6 -- 6 -
Tapto switch to
the rear camera

Why can't I share videos on social media?
Each video file is too big to share even if you set the clip size to 1 minute. You must edit the
video to a maximum of 30 seconds and then share it on social media.
What does GST mean?
GST indicates G-sensor sensitivity levels. Level 0~ Level 4 indicates the sensitivity
level from low to high.
What if I forget my wifi password?
Contact the seller to get the reset file if it encounters an error when setting the SSID
and password.
- 7 -
GPS Playback
1) Navigate to the 'Online' tab, click 'Edit', and then select the video file you want to
download. Press 'Save' to download the video files to your device.
2) Navigate to the 'Local' tab and select the video you want to play, and the GPS track
will be displayed below the playing video.
My WiFi App Doesn't Connect
1) Make sure the camera is powered on and the correct wifi was connected.
2) Make sure the wifi app has been upgraded to the latest version.
3) For a smooth Wi-Fi connection between your smartphone and VSYS camera, make
sure the distance between both is within a range of 3~5 meters (10~16 ft).
When your smartphone connects to the camera, it creates a new WiFi network. In new
iOS or Android versions, your camera may stop using that network if it doesn’t detect
internet — which your dash cam will not provide.
If prompted "Stay connected to this network without internet?", just click "Yes" and
everything will be OK!
For Android Users:
Before connecting any Android device to the dash cam, it is recommend to turn off the
“Smart Network Switch” option in the Wi-Fi settings of the smartphone.
For iPhone Users:
Before connecting your iPhone to the dash cam, it is recommend that the “Wi-Fi Assist”
option is turned off .
Wi-Fi Connection Troubleshoot
If the problem still persists, we recommend you to Turn Off cellular data and other
internet connections on your mobile phone to fix the issue of your smartphone not
connecting to your dash cam.

The concave and convex bayonet of the joint shall be matched correctly
Screw Nut: Just screw the nut when the cable connected
but not twist the cable or the connector
Rubber damping ring
Screw
Double-sided
foam tape
Double-sided
foam tape
The connection should follow
the same color and the correct
arrow direction.
The input voltage never exceeds 5V and
the current needs to be 2A or above for
the USB power source to make sure the
dash cam works properly.
1) Connect cam 1 & cam 2 to the main unit.
2) Find the USB test cable and connecting to the power bank or USB adaptor to do a quick
test before installation.
3) Prepare installation if everything looks good.
Quick Test
Camera Installation
- 8 -
Quick Installation Guide
• Please do NOT flush the main unit, lenses, power module, and remote with the high-pressure water gun.
• Do not bend the cable nor twist the connector during installation.
• The main unit and lens cable should be away from the high-voltage circuit like xenon lamp, ignition plug etc.
• If your motorcycle is a traditional carburetor system please try to change a suitable R-value ignition plug
when you meet the interference phenomenon.
Front Cam
Main Unit
Wired Controller
Power Module
Rear Cam
GPS Module
MENU
OK

- 9 -
Wired Controller
LED Light Frequency DVR Status
Slow blinking Recording properly
Fast blinking Emergency record mode
Steady (light on) Stop recording
Off (light off) Power off
Red LED Light
1) Short press the red button of the wired controller in Video Mode to activate Emergency
Recording Mode and take the snapshot (Video file name as KEY_XXX.MOV).
2) Long press the red button in Video Mode to enter Drag Racing Mode. And then:
• Long press the red button in Drag Racing Mode to switch different modes.
• Short press the red button in Drag Racing Mode to start racing.
LED Light Frequency GPS Status
Slow blinking Searching for GPS signal
GPS working properly
Steady (light on)
Blue LED Light
LED Light Frequency DVR Status
Slow blinking Recording properly
Fast blinking Emergency record mode
Steady (light on) Stop recording
Off (light off) Power off
Red LED Light
1) Short press the red button of the wired controller in video mode to activate
emergency recording mode and take the snapshot.
2) Long press the red button of the wired controller during the recording to enter
Drag Racing Mode. And:
• Long press the red button in Drag race mode to switch different modes.
• Short press the red button in Drag race mode to start racing.
LED Light Frequency GPS Status
Slow blinking Searching for GPS signal
GPS working properly
Steady (light on)
1) Short press the blue button in video mode to switch the display to the rear camera
in full screen.
2) Long press in video mode to enter Smart Gauge Mode. And:
• Short press in Smart Gauge Mode to switch different information.
Long press it again to quit Smart Gauge Mode. •
Blue LED Light
Red Buttons
Blue Buttons
• Make sure the power module is installed in a place that can detect the bike vibration .
• The dash cam automatically powers on when the engine is started. It won't work if only the ignition switch is turned on.
• The dash cam will continue to record for approximately 5 minutes after the motorcycle is turned off, and then shut down.
How does the smart power cord work?
No need to connect to the ACC wires. It works by detecting the voltage change and
continuous vibration.
Power Module Installation
OF F
ON
+
-
Positive
Negative
A 12V wire that is
controlled by the key
+
-
ACC Version:
Connect red wire to the battery positive terminal, black wire to the negative terminal, and
yellow wire to the 12V port controlled by key ignition (ACC wires). The dash cam will
automatically turn on and off with your bike ignition.
Smart Version:
If you do not want to connect the yellow wire, then leave the yellow wire aside without
installing it, at which point the power cord will work on a smart power cord principle.
Double-sided foam tape
double- sided foam tape
1) Short press the blue button in Video Mode to switch the display to the rear camera in
full screen.
2) Long press the blue button in Video Mode to enter Smart Gauge Mode. And then:
• Short press the blue button in Smart Gauge Mode to switch different information.
• Long press the blue button in Smart Gauge Mode to quit Smart Gauge Mode.
3) Long press the blue button in to quit Drag Racing Mode Drag Racing Mode.

- 10 -
Smart Gauge Mode
Long press in video mode to enter Smart Gauge Mode, and
then short press to switch different display information. long
press it again to quit Smart Gauge Mode.
Speed
km/h
000
TRIP: 0 Km ODO:0 Km
Short-Term Memory
TRIP: 0 Km
0:09
0 km/h
1.9bar 1.9bar
26 ℃27 ℃
Location Information
LAT:N 55 41' 16"LAT:N 55 41' 16"LAT:N 55 41' 16"
LON:E 113 47' 9"LON:E 113 47' 9"LON:E 113 47' 9"
24 m24 m24 m
Battery Power Display
Sleeping: 00.0V
Riding: 12.31VRiding: 12.31VRiding: 12.31V
Parking: 00.0VParking: 00.0VParking: 00.0V
Date and Time
2019-06-26
15:15:50
Tuesday
Speed
km/h
000
TRIP: 0 Km ODO:0 Km
Short-Term Memory
TRIP: 0 Km
0:09
0 km/h
1.9bar 1.9bar
26 ℃27 ℃
Location Information
LAT:N 55 41' 16"LAT:N 55 41' 16"LAT:N 55 41' 16"
LON:E 113 47' 9"LON:E 113 47' 9"LON:E 113 47' 9"
24 m24 m24 m
Battery Power Display
Sleeping: 00.0V
Riding: 12.31VRiding: 12.31VRiding: 12.31V
Parking: 00.0VParking: 00.0VParking: 00.0V
Date and Time
2019-06-26
15:15:50
Tuesday
Drag Racing Mode
Long press the red button in Video Mode to enter Drag Racing Mode.
And then short press the red button in Drag Racing Mode to start
racing. Long press the red button in Drag Racing Mode to switch
different modes.
If you want to quit Drag Racing Mode, just long-press the blue button.
GPS
TPMS
Front camera view The best 5 records
Mode option
Countdown
Current time
Current distance
Current speed
Current voltage Battery voltage after 1 hour
of flameout
Battery voltage after 1min of flameout
Optional