VSYSTO V7T User manual

V7T Truck Dash Cam
User Manual
Thank you very much for purchasing the VSYSTO V7T dash cam.
Please read this manual carefully before use.
- 1 -

ATTENTION
Prohibit Obey
Please use this product under the premise of obeying traffic rules.
Do not install the device in a position that blocks the view or obstructs driving.
Do not disassemble or modify this product by yourself.
Do not use accessories not included.
Do not allow water to enter this product.
If the product makes an abnormal noise or smell,please stop using it immediately.
The waterproof rating of the camera is IP67, and the host is not waterproof.
When disposing of this product, please follow the classification principle and
do not discard it at will.
Do not store this product in a high temperature and humid environment.
WARNING
- 2 -
Safety Instructions
In order to use this product safely, please confirm that you fully understand the
following.
WARNING: This section indicates that mishandling can have serious
consequences.
Note: This section indicates that improper handling may cause injury to the
user or damage the product.

Features
Replace conventional lithium batteries with super capacitors for
longer life and safer.
1.HD display screen.
2.Support reversing auxiliary line.
3.Support battery voltage display.
4.Video can be recorded after inserting Micro SD card.
5.Built-in WiFi, can view real-time video on the dedicated APP.
- 3 -
Standard Accessories
※If there is any change of specification and appearance due to improvement,
we are not able to inform you in advance. Please understand.
※Please note that there are differences between the schematic diagram and
the real object in the manual.
Host Front Camera
Power Cable
Rear Camera
3.5m
UserManualRemoteControl GPSModule

- 4 -
Description of Each Part
1
2
3
4
6
5
11
14
7 9
Up Button
1
OK Button
2
3
4
5
Down Button
Card Slot
Reset Button
13
12
8 10
6
7
Microphone
Power Connector
8GPS Connector
9Camera Connector
10 Camera Connector
11 Power Cable
12 GPS Module
13 Camera
14 Camera

- 5 -
Micro SD Card
1.Please use the high-quality Class10 or above genuine SD card.
2.The recorder supports 16G-256G memory card.
3.If the memory card cannot save the file properly, please format it on
the recorder.
※Formatting will delete the data, please backup the card data before
performing formatting.
1. Insert the card into the card slot as shown in the picture.
2.When picking up the card, gently press the SD card and slowly
release it after hearing "Da”.
3.Please pay attention to the direction of the gold finger on the SD card.
If it is inserted reversely, the SD card and recorder will be damaged.
Attention:
1.The card used on other devices will be automatically formatted
after being inserted into our DVR. Please back up the data.
2.In the case of high frequency of use, it is recommended to format
the memory card every two weeks.
3.Please do not pull out the card in the recording state to avoid
damaging the video file and recorder.
Specifications
Model V7T SD Card Support up
to 256GB
Screen Size 7
lnch(1024x600) G-sensor Built-in
Video Resolution 1920*1080P Speaker Built-in
Video Format MOV(H.264) Microphone Built-in
Loop Recording Support Working Voltage DC 5V-2A

- 6 -
Installation Guide
Please connect the yellow wire on the rear camera
to the 12V positive pole of the inverted light. When
the vehicle is in reverse gear, the rear camera
screen will be displayed in full screen on the main
unit of the recorder, with a reversing auxiliary line. It
is convenient for users to observe the surrounding
environment when reversing.
Rear Camera Host
Front Camera

- 7 -
Host Fixed Installation Diagram:
1. Hang it on the windshield.
2. Stand on the center console.
Note: You can choose to rotate 180° to adjust the screen interface in
the host menu.
Host Fixed Installation Diagram

- 8 -
※This recorder uses the latest supercapacitor design to replace the traditional
lithium battery design, supercapacitor will automatically charge and can save the
last file after disconnecting the power.
After installing the recorder and inserting the SD card, insert the charger into the
cigarette lighter. Start the car to start recording automatically.
Time Setting
Manually Trigger Lock Video
Power on
Attention
Pause recording after the recorder is turned on→Enter Menu→Choose time
setting→Press↑↓to adjust time→Press ok to save the settings
In the recording state, long press the up button, the recorder will enter the emergency
lock mode, record a locked video and the front and rear cameras capture a picture at
the same time. The video file name is named after KEY-XXXXX. The locked video will
not be overwritten by the normal recorded "REC-XXXXX" file. When the SD card
video file exceeds 10 KEY-XXXXX videos, the system will delete the earliest KEY-
XXXXX emergency video.
G-sensor trigger lock video
In the recording state, if the G-sensor sensitivity is turned on, the video will be locked
after the G-sensor is triggered by a collision and reaches the system preset level. And
the locked video will not be overwritten by the normal recorded "REC-XXXXX". The
name of the locked video file is GSR-XXXXX. When the SD card video file exceeds
10 GSR-XXXXX videos,the system will delete the earliest emergency video of GSR-
XXXXX.
Recording Mode
Please format the SD card before inserting it. After inserting the SD card, turn on
the power of the motorcycle, and the recorder starts to enter the normal loop
recording mode. You can set 1/2/3/5 minutes to save a video in the menu. When
the SD card is full, new video files will overwrite the oldest saved files. To prevent
loss of important files, please backup important video files in time.
Playback Video Mode
In the recording state of the recorder, short press the OK button to pause the
recording. Then long press the OK button, the recorder enters the system setting
interface, use the up/down button to select the video to be played, and then short
press the OK button to enter the playback mode. In playback mode, long press the
up button to switch to view the video files saved by the front and rear cameras. If
you need to exit the playback mode, long press the OK button to return to the
system setting interface. Then use the up/down button to select the recording icon,
and then short press the OK button again to successfully return to the recording
mode.

- 9 -
Rear camera video files name identification: REC_ The year, month and time of current
video R.MOV
R/REC_220909-151201-001838R.MOV
1
1
"R/" indicates rear camera video playback
OK
2022/09/0 9 15:12:01 [00: 00:26]
Reversing auxiliary line
2022/09/09 15:12:01
Voltage
00:00:26 REC
-
+
14.11v
Microphone
Recording icon
Lock
video
Video time
P
50M
1007HPA
0
mi/h
GPS
Front Rear
GPS
Date&Time
Parking
Monitoring
Countdown
Altitude
Atmospheric
pressure
Rear
Camera
Speed
WiFi
Front
Camera
"F/" indicates rear camera video playback
F/REC_220909-151201-001838F.MOV
1
1
2022/09/0 9 15:12:01 [00: 00:26]
Screen Information and Menu Descriptions
1.After selecting, press
to enter recording mode.
2.The icon becomes larger
to indicate that thefunction
has been selected.
Description of characters on the display
in recording mode:
When parking is detected, the
recorder will turn off after the
progress bar is complete, which
takes about 5 minutes
OK
1.After selecting, press
to enter playback mode.
2.The icon becomes larger
to indicate that the function
has been selected.
1. Press to select the video to playback
Front camera video files
name identification: REC_
The year, month and time
of current video F
In playback mode, long press
for 3 seconds to switch to view
the list of video files saved by the
front and rear cameras .MOV

-10-
1.Video clip time
※The specific functions are subject to the actual
product received.
2.Sound record
3.MIC sensitivity
4.Flameout Detection
5.Parking Monitoring
6.Parking Monitoring
Sensitivity
7.Timed Recording
after Flameout
1/2/3/5 minutes can be selected
Set whether the recorded video needs sound
Set the sound level of MIC
On:After detecting that the vehicle is turned off, the
recorder shutdown after waiting for about 10seconds; off:
After 5 minutes without vibration, the recorder shutdown
Set whether to turn on or off parking monitoring function
Set the sensitivity of parking monitoring
Set the time to keep recording after the vehicle is turned off
Whether the recorder display needs to be flipped at 0°/180°
Whether recording video needs date watermark
Set the speed unit displayed when driving
Set the button sound on or off
Set display time
Three format options: YYYY MM DD/MM DD YY/DD MM YYYY
Set the display screen backlight to be off, or off after 1min/3min
G-Sensor sensitivity level adjustment
Display the current number of satellites, longitude, latitude, etc.
Time zone selection around the world
Restore to the factory default settings
On/Off
Delete all videos from the memory card
Information about the current software version of the recorder
Note:"Flameout Detection ", "Parking Monitoring"
"Parking Monitoring Sensitivity ", and ''Timed Recording
after Flameout " functions are optional and require the
purchase of an additional power cable to have them. If you
need these three functions, please contact us through the
Amazon message system or customer service email.
OK
1.After selecting, press to enter language selection mode.
2.The icon becomes larger to indicate that the function has been selected.
1.Language identification -- corresponding to
the selected language.
2.The number of language options depends on
the actual model.
OK
1.After selecting, press to enter setting mode.
2.The icon becomes larger to indicate that the function has been selected.
8.Flip Screen
9.Date watermark
10.Unit system
11.Button sound
12.Clock setting
13.Date format
15.Auto screen off
16.Protection Level
17.GPS Status
18.Time zone selection
19.System reset
20.WiFi MODE
21.Format SD card
22.FW version
Whether it is necessary to turn on the driving speed display
when playing videos on the computer
14.Speed watermark