VSYSTO F9D User manual

Packing List
-1-
Product Appearance Diagram
Power Cable Interface
Wire Controller Interface
Camera1 Interface
Camera2 Interface
TF Card Slot
Type-C Interface
Screw Holes
Bracket Hole
Display Screen
(Can be connected to a computer
and used as a USB flash drive)
Dash Cam
F9D
UserManual V1.9
1) Dash Cam Main Unit*1 2) Camera *2
3) Power Cable*1 4) USB Test Cable*1
5) Tie*8 6) Bracket*1
7) Wire Controller*1 8)GPS Module*1(Optional)
9) Memory Card x 1(Optional) 10)Tire Pressure Sensors x 2 (Optional)
After opening the package, please confirm whether the driving recorder is in
good condition and the accessories are complete.
"Optional" mean it is not a standard configuration. Please refer to the product description on the
platform you purchased!

-2-
1.Quick Test and Installation
Please refer to the "Quick Installation Guide".
2.Insert the Memory Card
Insert the memory card into the card slot until you hear "Da". If you want to take out the card, gently
press the memory card and slowly release it after hearing "Da".
How to use
Tips：
Please insert the memory card in the correct direction.
※Please do not pull out or insert the card when it is turned on to avoid damaging the video
file and recorder.
※Please use the high speed Class 10 or above genuine card.
※Please format the memory card regularly to keep it in good condition.
Power on/off
After the recorder is properly installed, when you turn on the motorcycle power with the key, the
recorder turns on. Turn off the motorcycle power, the recorder turns off.
Video Recording
1)Normal Recording Mode
After the motorcycle power is turned on, the recorder will automatically start recording, and the LED
indicator on the remote controller will slowly flash. When the motorcycle power is off, the recorder will
automatically stop recording(If the smart power cable is configured, there is no vibration within 5
minutes after the motorcycle power is turned off, the recorder will shut down. Or long press the up
button on the wired remote controller for 3 seconds to shut down the recorder).
▶Loop Recording: The recorder will save a file after recording for a period of time (the default setting is
3 minutes). When the memory card is full, the system will delete the oldest file. You can manually set
the time of video recording in APP. 1/2/3/5 minutes can be set, and front and rear camera files are
saved in F and R folders respectively. The normal recorded video file is named "REC-xxxx".
2)Emergency Recording Mode
▶G-Sensor emergency recording mode: When the motorcycle collides with other vehicles or the
vibration is strong, the built-in G-Sensor will automatically activate the emergency recording mode.
The LED indicator on the remote controller flashes rapidly. The emergency video file is named "GSR-
xxxx". You can set the sensor sensitivity level in the menu or APP. The higher the sensitivity, the easier
to trigger G-Sensor.
▶Manualemergencyrecordingmode:Whentherecorderisrecording,shortpressOKbutton of
wiredremotecontrollertolockthecurrentrecordedvideo,andthefrontandrearcameraswill
captureaphotoatthesametime.Themanuallylockedvideofileisnamed"KEY-xxxx".
Tips：
※If the memory card is not inserted or is faulty, the video cannot be saved.
※"KEY" and "GSR" emergency video files can be saved 10 each. After more than 10, the
system will automatically delete the earliest one.

-3-
The APPisamobilephonecontrolsoftwareusedwithVSYSTODVRdevice.Thissoftwareisconnected
totheDVRdeviceviaWi-Fi,itcandirectlypreviewandplaybackthevideoonthemobilephone,easily
realizethatviewingthecameradocumentsonthescreenofmobilephone,settingor otheroperations.
Subvertingthecontrolmethodoftraditionalcameras,bringyouanewexperience.
Video File Format
Method 1: Scan the corresponding QR code to download
the latest APP from software download link of your browser.
Method 2: You can search "VSYSTO" on Google Play or
APP Store to download and install it.
DVR WiFi Default Name: F9_XXXX
Default password: 1234567890
Connection Steps:①Turn on the recorder
②Enter the WiFi setting interface of the phone, find the corresponding WiFi name, and enter the password
to connect to WiFi③Open mobile APP, connect the recorder
 Tips:
※If "No network connection" is displayed when connecting to WiFi, please turn off the mobile data
network first, and then connect to the recorder WiFi according to the steps. If the prompt "Current
WLAN is unavailable, whether to switch to another network?" appears, you must click "No".
※After entering the APP, the recorder will pause recording. Please click the red recording button on
the APP to start recording. After exiting the APP, the recorder will start recording in 30 seconds.
※You don't need to connect to WiFi for daily riding. Connect when you need to watch the video.
※In case of connection failure, please contact customer service.
2023/02/21 15:12:01 REC OKB/S
2023/02/21 15:12:01 VSYSTO F9 OKPH
Click it to switch the
front and rear cameras Click "Edit" to select the file to download or delete
APP Setting Interface
※Pause recording video and then
set it; It is recommended to set Level
0 or Level 1 for GST (G-sensor
sensitivity). Do not set it too high.
REC_220525-173957-00053F.MOV
Recording Mode
Year-Month-Day
F-Front camera
R-Rear camera
Video FormatNumber
Video
Recording Time
Mobile Phone APP Installation and Operation
F9

-4-
◆Function operation
75
km/h
605HPA
53M
22.3
°C
BACK
倒⻋
UpButton：
①In the front and rear camera split screen mode of the video recording interface,
short press the up button to switch to a single full front camera screen.Short press
the up button again to switch to a single full rear camera screen.Then Short press
the up button again to return to the left and right split screens.camera video long
press the up button to switch to the rear camera video file.
※The software defaults to split screen images for left and right display.When you
select which display mode,the recorder will remember it.Next time you turn on the
recorder it will be the previous display mode you selected.
OKButton：
①In the video recording interface, short press the OK button once to enter the
emergency video mode, and the front and rear cameras will capture a photo at the
same time.The emergency recording locked video filename is: KEY-XXXXXX.
※If there are more than 10 videos named KEY-XXXXXXX in the folder saved by the
front or rear camera in the memory card, the system will automatically delete the
oldest video.
②In the video recording interface,long press the OK buttonto enter the setting
interface.You can use the up/down button to operate the settings required by the
main unit. When the required functions are set long press the OK button to return to
the video recording interface.
Down Button：
①In the video recording interface, short press
the down button once to switch to the full screen
mode of the rear camera,which can be used as
a back up camera. Then short press the down
button once to return.
②In the video recording interface, long press
the down button to enter the auxiliary mode,
you can view Speed, Tire Pressure and
Temperature, Battery Power Display, Location,
Short-term Memory, Date &Time.
LEDRedLight:
-Red light slow flashes-Camera is recording normally, the video file name is
REC-XXXXXXX.
- Red light constant lights- Camera pauses recording.
- Red light fast flashes- Camera triggered the gravity sensor to record emergency
video, the video file name is GSR-XXXXXXX.
※If there are more than 10 videos named GSR-XXXXXXX in the memory card, the
system will automatically delete the oldest video.
W5T Wire Controller Operating Instructions
Connectto
themainunit
LED Blue Light:
After connecting the GPS module:
①Blue light-Slow flashes-GPS is searching for satellites, the satellite icon in the
upper left corner of the display is white.
②Blue light-Constant lights-The GPS positioning is successful,and the satellite
icon in the upper left corner of the display is green.

-5-
1.After selecting, press [OK] to enter
Video Mode.
2.The icon becomes larger to indicate
that the function is selected.
1. Press to select the video to playback
1. Character description on the display in recording mode:
"F/"indicates front camera video playback "R/" indicates rear camera video playback
2023/02/2115:12:0100:00:26
75
km/h Lock File
WiFi
Date & Time
Information
Temperature
Speed
Tire pressure
Warning Value
605HPA
53M
1. Video clip time 1/2/3/5 minutes can be selected
2.Sound record On/Off
3.MIC sensitivity Set the sound level of MIC
4.LCD Power Save Set the display screen backlight to be off, or off after 1 min/3min
5.Parking monitoring On/Off
6.Parking monitoring sensitivity Set the vibration sensitivity when parking
7.Recording Time After Flameout Set recording time after flameout
8.Date format 3 options YYYY MM DD/MM DD YYYY/DD MM YYYY
9.Clock setting Day&Time
10.Time zone selection Time zone selection around the world
11.Date watermark Whether the recorded video needs date watermark display and other options
12.Speed watermark Whether it is necessary to turn on/off the driving speed display when playing video on the computer or app
13.Overspeed alarm Set the overspeed alarm value. When the driving speed exceeds the preset value,
the recorder will issue an alarm prompt.
14.GPS status Display the current number of satellites, longitude, latitude and other information
15.Unit system Set the speed and temperature unit selection displayed when driving
16.Tire pressure function(Optional) On/Off
17.Tire pressure unit(Optional) 2 unit options (bar/psi)
18.Tire pressure alarm sound(Optional) On/Off
19.Tire pressure alarm threshold(Optional) Set the alarm sound for the lowest and highest values of tire
20.Rear camera mirror Whether mirror selection is required for the rear camera display
21.Protect Level G-Sensor sensitivity level adjustment
22.Button sound On/Off
23.Voice prompt On/Off
24.System reset Restore to the factory default settings
GPS
Front/Rear
Camera
R/REC-230221-151201R.MOV
1
1
F/REC-230221-151201 F.MOV
1
1
2023/02/2115:12:01[00:00:26] 2023/02/2115:12:01[00:00:26]
Video Time
22.3
°C
F/R
25.WiFi mode On/Off
26.Format SD card Delete all videos from the memory card
27.Operation guide Introduce the operation method of the button function of the wire controller
28.FW version Information about the current software version of the machine
Images Information and Menu Description
1. After selecting, press [OK] to enter
Playback Mode.
2. The icon becomes larger to
indicate that the function is selected.
1. After selecting, press [OK] to enter
Setting Mode.
2. The icon becomes larger to indicate
that the function is selected.
1.After selecting, press [OK] to enter
Language Choosing Mode.
2. The icon be comes larger to indicate
that the function is selected.
Altitude
Recording
SupportParkingMonitoring
Atmospheric Pressure
Microphone
Long press for 3 seconds in
the Playback Mode to switch to
the video files list of front and
rear camera
1. Front camera video files
name identification:REC_
The year, month and time
of current video F.MOV
2. Rear camera video files
name identification:REC_
The year, month and time
of current video R.MOV
1. Language identification — Corresponding to the
selected language.
2. The number of language choices depends on the
actual model.

-6-
1.Long press the down button of the wire controller
to enter the auxiliary display mode, and the
driving speed is displayed on the first interface
ODO 92Km
0:09
92km/h
12.31V
Sleeping:00.0V
Parking:00.0V
Short - term Memory
Tire Pressure Display
Battery Power Displa
km/h
115
TRIP:0 Km
Speed
15:15:50
2023-02-21
Tuesday
Date &Time
Current speed
while driving
2.Short press the up button again
to enter the tire pressure monitoring
interface(optional)
Tire Pressure
and Temperature
The voltage after
flameout for one hour.
Current Voltage
The voltage after
flameout for one minute
Time of short
time driving Year Month Day
Current Time
Current Week
24m
Location
599HPA
5541'16"
N
5541'16"
EGPS Longitude
GPS Latitude
Altitude
Atmospheric
pressure
1.5bar
°C
27
1.4bar
°C
27
Auxiliary Display Mode
3.Short press the up button again to enter
the battery power display interface
4.Short press the up button again
to enter the GPS information interface
Average speed
of short-ter
6. Short press the up again to enter the 5. Short press the up again to enter the current
mileage short-term memory interface year, month, and day interface
m
 Tips:
※Speed, short-term memory, and location functions require GPS support.
※Battery voltage display requires parking monitoring ACC power cable support.

or
-7-
5V2A
5V2A
OK
Installation Guide
1.Quick Test
1) Connect the front and rear cameras to the host of the recorder.
2) Find the USB test cable from the accessories and connect the recorder with a 5V 2A power bank or
USB charger.
After the recorder is turned on, test the function of the recorder.
3) After the test shows that the recorder is normal, you can install it.
If the output voltage exceeds 5V, the recorder may be burnt.
!
Waterproof
Camera
Main Unit
Waterproof wire controller
Power Cable
Waterproof GPS module
It is suggested to install
it on the handlebar
Waterproof
camera
OK
It needs to be exposed in the place where there is no
obstruction. And the distance from GPS to camera and main
unit shall be about 30CM to avoid signal interference.
It is recommended not
to install it near the
exhaust pipe, to avoid
the adhesive on the
bottom of the camera
bracket melting and
falling off due to high
temperature.
◆Camera Bracket
◆Camera
Installthecamerabodyonthebracket,and tighten thescrewstofixitafteradjustingtheproperangle.
Extension cable
During installation, it is recommended to install the extension
cable first, and then connect the host and camera separately
(so that the installation is easier). If the distance between the
host and the camera is less than 0.5 meters, it is
recommended not to use the camera extension cable (please
keep the camera extension cable for future needs).
The concave and convex bayonet of
the joint shall be matched correctly
Screw ring
（）
Connect to
the host
After the cables are connected, tighten the
screw ring. Do not twist the wire position.

-8-
2.Install Power Cable
ACC Power Cable Connection Method: The red wire is connected to the positive pole of the motorcycle
battery, the black wire is connected to the negative pole, and the yellow wire is connected to the positive
pole of motorcycle key control (12V ACC power source).
Tips：
The power cords configured for different models are different. Please refer to the products
actually purchased.
※Test is required after connection. After the motorcycle power is turned on, the recorder will
turn on automatically. After the motorcycle flameout, the recorder is turned off. If you do not
know the circuit of the motorcycle, it is recommended to find a professional person to install it.
▶This product is an auxiliary (vehicle driving recorder) product for safe driving. Any loss caused by
malfunction, information loss or using this product is irrelevant to our company.
▶This product is an auxiliary device for recording external images of vehicles. Due to the different
driving environment and vehicle environment, some functions will not support. The unscheduled
firmware upgrade in order to improve the product will change the performance of the product, and
sometimes the camera will cannot record due to the environment, so the driving images recorded in
this product is for reference only. The state of memory card will also lead to camera cannot record.
▶Although this product can record and save the videos of accidents, it does not guarantee that all the
accident videos can be recorded. Slight collision accidents can't start the collision sensor, so the video
may not be recorded in the specialized folder.
▶Be sure to disconnect the power supply when inserting or pulling out memory card. For the stable use
of the product, it is recommended to format the memory card twice a week.
▶Generally memory card has a service life. Long-term use of memory card may cause the new data to
be unable to save. In this case, it is recommended to buy a new memory card to use. Our company will
not be liable for data destruction caused by the long-term use of memory card.
▶Do not use high-pressure water gun or chemical solvent to clean the host, camera, power module
and other parts (otherwise, no warranty will be given).
▶Please do not use it in an environment with excessive dust density, so as to prevent cameras and
other parts from being contaminated with dust, which will affect the video effect.
▶Do not twist cables or cable connector during installation, and keep the recorder host and wires away
from high-pressure areas.
▶Please replace the spark plug with a spark plug with appropriate R value if there is interference in
some motorcycle models.
▶Do not disassemble, modify or repair this equipment by yourself. If the recorder fails due to this, we
will not provide after-sales service.
▶Some pictures, functions and specifications may change due to product or software upgrading.
Please understand that we cannot notify you separately.
▶For your safety, please do not install or operate this product while driving. Please use it within the
scope permitted by law
▶Disclaimer:Tire pressure sensors may not fit all vehicle tires. Please consult your vehicle manual or a
tire professional whether the tire pressure sensors are fit your car. If they affect your vehicle's
performance, driving, or insurance coverage,do not install it!
◆ Notes