VSYSTO S2F User manual

- 1 -
MOTORCYCLE DASH CAM
S2F USER MANUAL

- 2 -
This product records videos while the motorcycle is operating. Use this product only for
reference when investigating incidents or road accidents. This product is not guaranteed to
record ALL events. The device may not properly record accidents with small impacts that are
too minor to activate the impact sensor or accidents with massive impacts that cause the
motorcycle’s battery voltage to deviate. Video recording does not begin until the product is
completely turned on (booted up). To ensure that all motorcycle events are recorded, wait until
the product is completely booted up after turning it on, and then begin operating the motorcycle.
VSYS is not responsible for any loss caused by an accident, nor is it responsible for providing
any support regarding the outcome of an accident.
Before using the product
During use of the product
Read the following safety information to properly use the product.
• Please format cards before use and anytime a significant amount of data has been
collected to ensure that the device and SD cards are working properly together. It is
recommended to format the TF card at least once a week.
• Use the product at a temperature between -20°C to 65°C. The product may not
function as designed and some permanent physical damages may result if it is
operated out of the specified temperature ranges. Such damages are not covered by
the warranty.
•The product emits electromagnetic radiation that might interfere with medical
devices. Consult with your physician and your device manufacturer if you are uncertain
whether you can use this device.
• Please use this product to the extent permitted by law.
• Do not operate the product while driving a motorcycle. Distraction while driving may
cause accidents and result in injury or death.
• Do not install the product in a place exposed to flammable gas. Doing so may result in
fire or an explosion.
• Do not use the product in a place with high humidity or temperature. It may cause
malfunction of the product, explosion, or fire.
• Do not disassemble the product or subject the product to impact. Doing so may
damage the product. Unauthorized disassembly of the product voids the product
warranty.
• Do not fully submerge the product in water. Doing so may damage the product.
• Do not use the product outside for a prolonged period of time when it is raining. Doing
so may cause water damage to the product.
• Do not clean the product with chemicals or detergent. Doing so may damage the
product. Clean the product using a clean, soft, dry fabric.
• Ensure that the memory card is in the correct direction before inserting it into the
product. The memory card slot or the memory card may be damaged if it is inserted
incorrectly.

- 3 -
Packing List
Connection Diagram
The connection may change without prior notice.
The items may vary for different buying options.
Card Slot
Screen Mounting holes
Speaker
Camera 1
Power cable
Wired remote
MIC
Camera 2
Main unit structure
The product design may change without prior notice.
Cable ties
Handlebar mount
Front camera & extension cable
Rear camera & extension cable
USB test cable
GPS tracker
Power cord
Main unit
Wired Controller
OK

- 4 -
Short press to select the video to playback
R/REC-211019-120514R.MOV
1
1
RearCam
F/REC-211019-175340R.MOV
1
1
2021/10/19 17:53:25 [00:00:26]
“F/” indicates front cam video playback “R/” indicates rear cam video playback
Video recording time
WiFi
Date & time information
Recording
2021/10/19 17:53:25 [00:00:26]
Select the setting options and
press the [OK] button to enter
Video Mode.
Select the setting options
and press the [OK] button to
enter Playback Mode.
Select the setting options and press the
[OK] button to enter Setting Mode.
Select the setting options and press the
[OK] button to enter Language Settings.
Menu Setting Description
* Press [OK] button of remote controller to pause recording before setup the system, then
long press [OK] button to enter menu system.
“REC” means normal video file
“GSR” means file recorded by triggering G-sensor
“163256” means time 16 o’clock 32 minutes 56seconds
“MOV” means video file format
“170809” means date 9th August, 2017
“F” means front camera video file
“KEY” means file recorded by pressing remote
Atmospheric pressure
Altitude
DVR shutdown
countdown after
engine off
Video file name information: REC_170809-163256F.MOV
Short press in video mode to switch
different display mode;
Long press to enter smart gauge mode.
•
•
•
NOTE: The recorder will lock the latest 10 emergency recording videos(GSR-XXXX.MOV)triggered by G-sensor
and 10 emergency recording videos(KEY-XXXX.MOV) manually triggered by the remote from being overwritten,
and after more than 10, the recorder will automatically start to overwrite the earliest locked emergency video.
Long press for 3 seconds in the playback mode to switch
the video files list between front camera and rear camera.
•

- 5 -
Quick Installation Guide
Parking monitoring On/Off
Set the vibration sensitivity when parking
Video clip time 1/2/3/5min can be selected
Sound record
On/Off
MIC sensitivity Set the sound level of mic
Auto screen off Set the LCD backlight off, or off after 1min/3min
Date format YYYY MM DD/MM DD YYYY/DD MM YYYY
Clock setting Day & Time
Rear camera mirror Set the mirror image display for rear camera
Protection sensitivity G-sensor adjustment
Button sound On/Off
Voice guide On/Off
Format SD card Delete all videos from the memory card
WiFi mode Wifi On/Off
System reset Reset your device to factory settings
FW version Check the firmware version
Recording time after
flame out Set recording time after flame out
(15min/30 min/1H/ 2H/3H )
Parking monitoring
sensitivity
Time zone selection Time zone selection around the world
Speed watermark Turn on/off the driving speed watermark
when playback videos on the PC/APP
GPS Status Display the current number of satellites,
longitude, latitude and other information
Unit system Set the speed unit displayed when driving
NOTE: The settings may change without prior notice!
ATTENTION
• Please do NOT flush the main unit, lenses, power module, and wired controller with
the high-pressure water gun.
• Do not bend the cable nor twist the connector during installation.
• The position of the main unit and lens cable should be away from the high-voltage
circuit like xenon lamp, ignition plug etc.
• If your motorcycle is a traditional carburetor system please try to change a suitable
R-value ignition plug when you meet the interference phenomenon.
Front Cam
Main Unit
Wired Controller
Power Module
Rear Cam
OK
Parking monitoring On/Off
Set the vibration sensitivity when parking
Video clip time 1/2/3/5min can be selected
Sound record
On/Off
MIC sensitivity Set the sound level of mic
Auto screen off Set LCD backlight off, or off after 1min/3min
Date format YYYY MM DD/MM DD YYYY/DD MM YYYY
Clock setting Set date & time
Rear camera mirror Set the mirror image display for rear camera
Protection sensitivity G-sensor adjustment
Button sound On/Off
Voice guide On/Off
Format SD card Delete all videos from the memory card
WiFi mode Wifi On/Off
System reset Reset your device to factory settings
FW version Check the firmware version
Recording time
after flame out
Set recording time after flame out
(15min/30 min/1H/2H/3H )
Parking monitoring
sensitivity
Time zone selection Time zone selection around the world
Speed watermark Turn on/off the speed watermark
when playback videos on the PC/APP
Display the current number of satellites,
longitude, latitude and other information
Unit system Set the speed unit displayed when driving
NOTE: The settings may change without prior notice!
GPS Status
Wired Controller
GPS Module
Menu Setting Description

The concave and convex bayonet of the joint shall be matched correctly
Screw Nut: Just screw the nut when the cable connected
but not twist the cable or the connector
Rubber damping ring
Screw
Double-sided
foam tape
Double-sided
foam tape
- 6 -
The connection should follow
the same color and the correct
arrow direction.
The input voltage never exceeds 5V and
the current needs to be 2A or above for
the USB power source to make sure the
dash cam works properly.
1) Connect cam 1 & cam 2 to the main unit.
2) Find the USB test cable and connecting to the power bank or USB adaptor to do a quick
test before installation.
3) Prepare installation if everything looks good.
Quick Test
Camera Installation
+
-
Positive
Negative
Double-sided foam tape
double-sided foam tape
+
-
Power Module Installation
- 6 -
Connect red wire to the battery positive terminal, black wire to the negative terminal.
The smart power module works by detecting the voltage change or continuous vibration.
• Make sure the power module is installed in a place that can detect the bike vibration .
• The dash cam automatically powers on when the engine is started. It won't work if only the ignition
switch is turned on.
• The dash cam will continue to record for approximately 5 minutes after the motorcycle is turned off,
and then shut down.

2) Fix the GPS module to a proper place on your motorcycle with the double-sided foam
tape. Please note the “GPS” icon must face the sky directly without any barrier, in case
of the signal is shielded.
GPS
GPS
Double-sided tape
“GPS” icon needs to face to the sky
The concave and convex bayonet of the joint shall be matched correctly
1) You can go to our official website to download the GV player.www.szv-sys.com
GPS Module Installation
- 7 -
OK
Short press in video mode to switch the display to the rear camera in full screen;
Long press in video mode to take snapshots and enter the manual emergency
recording mode.
Short press to pause video recording, and then long press to enter Menu Settings
Short press in video mo s.de to switch the different display mode
Long press in video mode to enter Smart Gauge Mode, and then short press to
switch different information.
LED Indicator
Wired Controller
LED Light Frequency Camera Status
Slow blinking Recording properly
Fast blinking Emergency recrod mode
Steady (light on) Stop recording
Off (light off) Power off
NOTE: The recorder will lock the latest 10 emergency recording videos (KEY-XXXX.MOV)
from being overwritten, and after more than 10, the recorder will automatically start to
overwrite the earliest locked emergency video.

- 8 -
We constantly optimize and strive for excellence to make driving safer, and smart. Share
your product experience and story with us to inspire someone else.
If you have any thoughts on how we can do even better, we welcome your constructive
feedback and suggestions.Please do not hesitate to contact us, please contact us by
below ways.
[e-mail]
https://www.facebook.com/szvsys
https://www.youtube.com/c/szvsys
Contact Us
Shenzhen V-SYS Technology Co.,Ltd.
302, BUILDING A9, TIANRUI INDUSTRIAL PARK, NO. 35, FUYUAN FIRST ROAD,
ZHANCHENG COMMUNITY, FUHAI STREET, BAO AN DISTRICK, SHENZHEN, CHINA
ODO 92Km
0:09
92km/h
12.31V
Sleeping:00.0V
Parking: 00.0V
Short-term Memory
Battery Power Display
15:15:50
2021-06-26
Tuesday
Date and Time
24m
Location Information
599 HPA
41°24'12.2"
N
2°10'26.5"
E
km/h
115
TRIP:0 Km
Speed
Smart Gauge Mode
OK
Long press in video mode to enter Smart Gauge Mode, and then
short press to switch different display information.
Current voltage
Battery voltage after 1 hour
of flameout
Battery voltage after 1min
of flameout
Single driving time
Average speed of single driving
Altitude
Longitude
Latitude
Atmospheric pressure