VSYSTO T3 User manual

TRIPLE DASH CAM
T3 USER MANUAL

PACKING LIST
Main unit(Built-in Cam 1)
Separate cameras(x2)
Power module
2.4G Remote controller
19.7ft camera extension cables(x2) Trim removal tool
* The items above are only for reference and are subject to change without notice.
GPS module(Optional)
- 2 -
Suction cup mount

2
10
1
3
4
5
6
7
8
9
11
13
12
CONNECTION & STRUCTURE
* The connection and structure shown above are for illustration purposes only. The actual product may vary.
- 3 -
14

12
13
Card slot
1Up
Menu/OK
3Down 4
5Cam 3 port
6
GPS module(Optional)
7Split cable port 8
Power module
9
Cam 2 Cam 1
Microphone
Cam 2 port
2
10
11
Cam 3
CAM2
CAM 1
CAM3
- 4 -
14 Remote
We recommend doing a benchmark test before installation to ensure that all components
are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cables in the vehicle, when necessary a 0.5'' (12mm) hole should be drilled
for passing the camera cable through the vehicle's walls.
Step 3: Once all cables and wiring have been properly routed, perform a system function
test by temporarily connecting the system.
Before Beginning Installation
Installation Guide

Separate Cameras
Connect to
the main unit
The concave and convex bayonet of the joint shall be matched correctly
IR LED
Connect to Turn signal wire or Reverse signal wire: A full screen displays this
camera automatically when the turning or reversing signal is triggered .
Extension Cable Extension Cable
Power Cable
- 5 -
Separate Cameras
Cables
Monitor
1. Slide the suction cup mounting bracket's head into the monitor's back metal clip.
2. Before mounting the monitor, clean the mounting surface well.
3. Position the suction cup on the dashboard or on the windshield.
4. Press the suction cup against the surface and press the lockdown to fix it.
1. Be sure to position the cable properly. Do not run the cable over sharp edges, do not kink
the cable, and keep away from HOT and rotating parts.
2. Fasten all cables and secure all excess cables.
The concave and convex bayonet of the joint shall be matched correctly
Connect to cigarette lighter socket
Connect to
the monitor

Operation
The monitor display the left and right 2-split image by default, you can set different modes
by pressing the button on the main unit.
Left right front Left right front
Left right
* The dash cam will save the last setting when power is off, so it will show the display mode you used last time
when you turn it on again.
*The remote starts malfunctioning when the battery has become discharged, please replace the battery in the
remote controller(Battery model:CR2032).
The 2.4G wireless remote control can be used to easily view the image display of each
camera on the monitor.
When you want to turn left (or monitor the left side of the truck), short press button,
the DVR will display the left camera in full screen; short press the button again to
return to the default display mode.
When you want to turn right (or monitor the left side of the truck), short press the
button, the DVR will display the right camera in full screen; short press the button
again to return to the default display mode.
When you want to check the front view of the truck, double-click any button, and the DVR
will display the front camera in full screen; short press any button again to return to the
default display mode.
Left
X1 X1
Left Right
Front
X2X2 X2X2
Display Modes Switch (Main Unit)
Display Modes Switch (2.4G Remote)
- 6 -

Menu Setting Description
1. Press to select the video to playback.
2. Long press for 3 seconds in the Playback Mode to switch the video files list of front,Left and right camera.
R/REC-190218-120514R.MOV
1
1
2021/02/18 12:05:25 [00:00:26]
F/REC-190218-120 514F.MOV
1
1
2021/02/18 12:05:25 [00:00:26]
2021/03/02 14:48:46 0:08:17
Date&Time Emergency lock
Mic
L/REC-190218-120514L.MOV
1
1
2021/02/18 12:05:25 [00:00:26]
Set the loop clip time
Sound record Toggles the microphone on/off
MIC sensitivity Set the sensitivity of the microphone
Auto screen off Set the screen saver time
Date format YYYY MM DD/MM DD YYYY/DD MM YYYY
Clock settings Set date & time
Time zone select Time zone selection around the world
Speed stamp Turn on/off the speed watermark
Unit system Metric units, Imperial units
GPS Status Display the satellites, longitude, latitude information
Protect Level Set the sensitivity of the G-Sensor
Beep Turns the sound on/off for when button is pressed
Voice guide On/Off
Reset setup Reset your device to factory settings
Format SD card Delete all videos from the memory card
FW version Check the firmware version
Select the setting options and
press the [OK] button to enter
Video Mode.
Select the setting options and
press the [OK] button to enter
Playback Mode.
“F/” indicates front cam video playback “L/” indicates left cam video playback “R/” indicates right cam video playback
“REC” means normal video file
“163256” means time 16 o’clock 32 minutes 56seconds
“MOV” means video file format
“GSR” means file recorded by triggering G-sensor
“170809” means date 9th August, 2017
“F” means front camera video file
Video file name information: REC_170809-163256F.MOV
NOTE: The recorder will lock the latest 10 emergency recording videos(GSR-XXXX.MOV)triggered by G-sensor from
being overwritten, and after more than 10, the recorder will automatically start to overwrite the earliest locked
emergency video.
• Icon description in Video Mode
Select the setting
options and press the
[OK] button to enter
Setting Mode.
Select the setting
options and press the
[OK] button to enter
Language Settings.
Movie clip time
- 7 -
WiFi mode On/Off
Recording status
Video time

Model
Video format
Memory card
G-SENSOR
Loop Record
T3
MOV(H.264)
TF Card Up to 256GB
Support
Video Resolution Front:1080P@30fps; Left/Right: 720P@25fps
Microphone Built–in
Specifications
LCD screen 3.0 "IPS
Support(1/2/3/5min)
WiFi
Waterproof IPX7 for separated cameras
Night vison 4pcs IR LED(separated cameras)
*The parameters may change without prior notice.
- 8 -
Support
Contact Us
We constantly optimize and strive for excellence to make driving safer, and smart.
Share your product experience and story with us to inspire someone else.
If you have any thoughts on how we can do even better, we welcome your
constructive feedback and suggestions. Please do not hesitate to contact us,
please contact us by below ways.
Shenzhen V-SYS Technology Co.,Ltd.
302, BUILDING A9, TIANRUI INDUSTRIAL PARK, NO. 35, FUYUAN FIRST
ROAD, ZHANCHENG COMMUNITY, FUHAI STREET, BAO AN DISTRICK,
SHENZHEN, CHINA
[e-mail]
https://www.facebook.com/szvsys
https://www.youtube.com/c/szvsys