Watchguard ALL-PACK1 User manual

09
12
14
16 Alarm SystemDashboard
19 How to Use the Alarm Keypad
19 Accessories Enrollment
23 Configure the Accessories
24 Zone Setup
25 Recent Activity
26 Notification Rules
27 Electrical Facility Control
28 Phone Remote Control
29 Device Setup
33 Other App Setting
34 Smart Home Automation
36
37
38
41
14 Connect Alarm System to the App
32 Programming by Alarm Keypad

45

67

89

Download App
Connect Alarm System to the App

Alarm System Dashboard
Once the alarm system has been connected to your app,
the dashboard will be displayed.
Basic Information
Security Mode
Two-way Calling
Emergency SOS Alarm
Alarm Settings
System Status
Activitiy like event log etc.
Manage Accessories
Emergency Call
Press the SOS button in the event of an emergency. This will trigger an
immediate alarm even if the system is disarmed or in Home Mode.
To stop the alarm, press the disarm button on the app or remote control.
Press stay button, then press or button within 3 seconds arm arm disarm
to enter into arming or disarming state in mute mode without disturbing
someone.
Mute Mode
Stay Arm (Home Mode)
Sensors that are designated in the Home Zone are deactivated, allowing
you to move freely in your home. the sensors in Normal Zone will remain
active and if triggered, will immediately sound the alarm.
The Alarm System has three security modes and an
emergency SOS button.
Listen into the roon via the control panel and also speak with people
in the room.
Two-way Talk
Disarm the system when entering your home. All sensors will be
deactivated allowing you to move freely .
Disarm
Arm the system when leaving your home. All sensors will be activated.
Any sensors that are triggered will immediately sound the alarm.
Arm
（Note: Mute Mode only works for operation via Remote Control.)

Arm:
Press once，then press .“ ” “ ”
Disarm：
Press once，enter password “ ”
1234，then press .“ ”
RFID Reader：
Place it close to the RFID reader
to arm or disarm. The Function
(Arm only, Disarm only, Arm or
Disarm Switchable) can be setup
on the app. See page 23.
Stay Arm：
Press once，enter password “ ”
1234，then press .“ ”
How to Use the Alarm Keypad
Press “ “ icon to wake up the touch keypad.
Wake up Key
You can arm, disarm and switch between security modes using:
1. Touch keypad on alarm control panel
2. RFID Cards
3. Smart Life Apps
4.Remote Control
Through the Remote Control
(Press and hold the buttons
for about 1 sec.)
Disarm
Arm
Emergency Call
Home Mode
Tap on device , enter "T1"
the device interface.
Using RFID CardsUsing Touch Keypad
Arming and Disarming
Disarming and arming stay always need a password. The default password
is and can be changed by using the apps. (Check Page32, Setting-“1234"
Security Code for Disarming)
4 Ways to Control the Alarm System
SOS Emergency Button
Press and hold activiate key " "
to immediately trigger the alarm.
（Mute Mode only works for
operation via Remote Control.)

Speed Dialing
The system allows you to program up to 2 frequently called phone numbers
reduced to a single digit (1or 2).
To store speed dial numbers:
Open the app, enter Alarm System Dashboard > > Setting Store Alarm
Phone Number Speed Dail Numbers Enter the numbers to store> > >
Save
To dial speed dial numbers:
Wake up the touch keypad, then press and hold the number or ,
the number will be dailed immediately.
Note: If you enter the wrong numbers, tap the wake up key " " to erase
the numbers and call again.
Make a call
Wake up the touch keypad, type in the phone number, and then press the Call
Key “ ” to start the call.
phone number
Accessories Management
Tap on icon then into accessories menu, you can " "
customise the accessory name, select the zone type,and also
delete the accessory from the app, if required.
Accessories Enrollment & Zone
You are able to pair up to 50 additional sensors, 50pcs RFID cards,
10 remote controls or keypads to the alarm system. Sensors that
are included with the alarm system are already enrolled with the
control panel.More accessories can be paired in two ways.
Press the enroll button .
Input “XXXX*1#”
( XXXX is password, the
default password is 1234)
Step 1, Press the enroll code on touch pad or select the “ ”
on the dashboard to enter the Accessories Menu, then tap on" "icon.
Step 2, Trigger the sensors one by one. How to trigger different accessories:
2120

1
2
3
1 System beeps once, the LED light
flashes once, the enrollment is
successful.
2 If system beeps twice and the LED
light flashes once, the accessories
have been enrolled before.
3 If three beeps are heard and LED
light flashes once, the storage is
full.
(Note! Please don’t press tamper switch to enroll or enroll accessory in low battery
status, It will remain in enrolling mode for 30 seconds.)
Press any
button on
the remote
control.
Move the
transmitter
away from
the magnet
Press the black
button on the
rear of the
motion sensor.
RFID Card
Place RFID
card close
to the RFID
readerl.
Step 3, Press the enroll button again or press " "
icon on the app to exit the enrolling . The enrolled
sensors will automatically appear in the Accessories
menu in the app.
Configure the Accessories
Tap on icon on the dashboard to enter the " "
Accessories menu.
You are able to enable and disable accessories from this page.
We recommend that you give each accessory a unique name so it is easier
to recognise the location should an alarm be triggered.
You can also assign each sensor to a Zone Type (see page 24) To configure
any accessory, simple press the accessory name.
RFID Card
Name the Remote Control or RFID
tags, so you will receive the alerts that
tell you whose remote control or RFID
tags has armed or disarmed the Alarm
System.

Zone Setup
:Full power, 
:Low Battery
It allow s a de lay be for e entry or ex it
especially for sensors in single delay zone.
But accessories in normal zone, home mode
zone, and 24H zone will not be delayed.
Delay Zone
Normal Zone
The alarm is activated immediately when
triggered.
No matter what state the alarm system is
in, the accessories in 24 Hour zone are
triggered, the control panel will get the
signal and alarm immediately.
24 Hour Zone
Stay Zone
Press " " button, sensors in home mode
zone are disabled then the users can move
freely. While the sensors in normal zone will
st ill a ctiva te an immd ia te al ar m w he n
triggered.
Recent Activitiy
The alarm system monitors your home for activitity and sends you
an app push notification, calling or SMS when sensors are triggered.
All events can be checked by tapping on . “Recent Activity”

Call
Push
Notification
Smart Alarm
WiFi ON
SMS Mark
Smart Alarm
WiFi OFF
Call phone number 1,2,3,4,5
If anyone pick up the phone,
then it will stop calling next.
If anyone disarm by clicking on
button from notification window,
then the call ends too.
Call phone number 1,2,3,4,5
If anyone pick up the phone,
then it will stop calling next.
Notification Rules
If “Me-Setting-App Notification” is
disabled, then you will not receive
app notification when events are
detected but still have calling alert
or SMS alerts.
Electrical Facility Control
Tap on “ "to turn on electronic facilities like lights, or fences
to deter the intruder immediately in the event of alarm.
Note! Electical Facility is Off as default. To activate electrical facility, AC power
of control panel must be on.
This mo de is for someone at home. No rmal
zone se nsors ar e enable d while hom e mode
zone se nsors wi ll be disab led.
Stay Arm
Mode fo r no one at home. It se nds
noti fications when any detect or is trigg ered.
Arm
The al arm sys tem is dis able d. Only se nsor s in
24 hou r zone wil l trigg er the al arm.
Disarm
List en into t he room vi a the con trol pa nel and
also s peak wi th peop le in the ro om.
Two-way Talk
User c an choo se to soun d the sir en.
Emergency call
Electrical Facility Control
Check the connecting method on page 36
GSM M o de
Note: If no one pick the phone, the system will keep dailing for 3 times.

Central Station Setting
The system support Ademco Contact ID and SIA TCP/IP protocol
It's able to communicate alarms and events directly to the
Central Monitoring.
Configure reception of events on the CMS and specify the
encryption key if you intend to use encryption. The encryption
key may contain up to 32 HEX or 16 ASCII characters.
Enable "Connect on central station", and in the Protocol field,
select CONTACT ID or SIA Protocol, then enter the account
number of alarm panel, specify the central station tel number
or the primary and secondary IP address of the CMS.
In the event the alarm, the alarm system will call the preset phone
number, user can pick up the phone , monitor the site, and remotely
control system by entering below numbers.
Disarm the system, press ; 0
Arm the system in the away mode,
press ; 1
Turn on on site siren, press ; 7
Turn off on site siren, press ; 8
Monitor the site, press key; *
Press escape (#) or hang up to exit.
Phone Remote Control
8888 8888
00:01
+

RFID Card Operation Notification
Get notified who is operating the system via RFID tags.
Remote Control Armed/Disarmed Alert
Get notified who is operating the system via remote control.
Be notified if a Door/Window has been left open when the
Alarm System is armed.
Security Code for Disarming
The security code is used to control the system by using touch
keypad or sending SMS(should be 4 digits)
Send balance ceck code via SMS to the card operator.

Programming by Alarm Keypad
Each system installed will requir programming, by app or using the alarm system keypad.
Use the following outline if you programm the system by using alarm keypad.
Enter the password followed by * to start the setup. (default password 1234.)
Code Functions Mark
Password*0# To delete all enrolled accessories.
Password*1# Enter Accessories Enrollment State
Password*2#
Password*3#
Password*5*1*xxx#
Password*5*2*xxx#
Password*5*3*xxx#
Password*6*1*xxxxxx#
Password*6*2*xxxxxx#
Password*7*1*xxxxxx#
Password*7*2*xxxxxx#
Password*7*3*xxxxxx#
Password*8*1*xxxxxx#
Password*8*2*xxxxxx#
Password*8*3*xxxxxx#
Password*8*4*xxxxxx#
Password*8*5*xxxxxx#
Start Setup with the app.
Reset the system to default setting.
Set Alarm Duration Time in Minutes
Set Exit Delay Time
Set Entry Delay Time
Store Speed Dailing Number 1
Store Speed Dailing Number 1
Store SMS Number 1
Store SMS Number 2
Store SMS Number 3
Store Phone Number 1
Store Phone Number 2
Store Phone Number 3
Store Phone Number 4
Store Phone Number 5
"xxx" refer to
minutes values
"xxxxxx" refer
to mobile
phone number