Waterite WR2 Installation instructions

WR2
Residential Water Filtration System
INSTALLATION AND OWNER’S MANUAL
For all WR2 series residential filter systems
THIS MANUAL IS TO BE LEFT WITH THE OWNER OF THE EQUIPMENT FOR
REFERENCE PURPOSES AND TECHNICAL GUIDANCE. IT IS STRONGLY
RECOMMENDED THAT QUALIFIED DEALER SERVICE PERSONNEL BE CONTACTED
IN THE EVENT OF AN UNKNOWN INTERRUPTION OF SERVICE OR APPARENT
PRODUCT MALFUNCTION. AN ANNUAL PREVENTATIVE MAINTENANCE
INSPECTION BY A WATER PROFESSIONAL IS RECOMMENDED TO ENSURE
TROUBLE-FREE AND CONTINUOUS OPERATION.
R2

2
Congratulations!
You have purchased the finest residential filtration water system
available for your home. It will provide you years of reliable service if
properly installed, operated and maintained. Please read this entire
manual before attempting installation and operation.
Section 1. Frequently Asked Questions
Before getting started, take the time to familiarize yourself with your new Waterite system by
reading some FAQs listed below. Call us or ask your dealer if you have any other questions
about your system’s operation.
Q: Why filter your tap water?
Water filters are designed to separate particles of dirt and sediment from the raw water source.
Additionally, the carbon cartridge will reduce odour or taste causing contaminants, leaving your
water tasting fresh and pure. Your system will deliver filtered water to a faucet conveniently located
at your kitchen sink or any other designated area.
Q: How does the WR2 system work?
WR2 systems use 2 stages of treatment to produce your drinking water. The raw tap water first
flows through a 5-micron particle filter to remove dirt, rust and other sediment. The second stage is
a carbon filter that is used to reduce chlorine, many chemicals and remaining traces of taste and
odour from the plumbing system. Your system also includes a faucet and the hardware and tube
needed to complete the installation.
Q: Will WR2 filter systems remove sodium and salts from the water?
No. WR2 Series systems are not designed for the reduction of calcium or sodium salts in solution
in your raw water source. It will not reduce hardness or soften water.
Q: Does the WR2 residential filter system remove bacteria? Cryptosporidium? Viruses?
Simple water filters will not eliminate most bacteria, viruses and parasites such as Cryptosporidium
from the water. Where these conditions exist, cartridges and other system components will become
contaminated from exposure to them. WR2 filter systems should be periodically purged, right up to
the kitchen sink faucet, with chlorinated water to allow a disinfection of the unit, usually at the time
that the prefilter cartridges are changed. Make sure that you carefully follow the maintenance
and purging instructions provided.
!
THIS FILTER SYSTEM IS DESIGNED ONLY TO IMPROVE AESTHETIC PROPERTIES AND IS
NOT DESIGNED TO ACT AS A PRIMARY BARRIER TO WATERBORNE MICROBIOLOGICAL
OR TOXIC CHEMICAL CONTAMINATION. WHERE THESE CONDITIONS MAY EXIST
CONSULT A WATER PROFESSIONAL TO ENSURE SUFFICIENT RAW WATER PRE-
TREATMENT AND DISINFECTION.

3
!
WATERITE FILTER SYSTEMS ARE TO BE OPERATED ONLY WITH A SAFE, CHLORINATED
RAW WATER SOURCE.THIS IS NECESSARY TO PERIODICALLY PURGE AND FLUSH THE
SYSTEM WITH WATER THAT HAS A CHLORINE RESIDUAL TO SANITIZE PARTS OF THE
SYSTEM THAT NORMALLY ARE EXPOSED TO WATER THAT HAS BEEN DECHLORINATED
AND MAY BE SUSCEPTIBLE TO BACTERIAL CONTAMINATION. FOLLOW FLUSHING
INSTRUCTIONS AND CHANGE FILTER CARTRIDGES AT RECOMMENDED INTERVALS.
Q: What does filtered drinking water taste like?
As most of the sediment and chlorine will be removed, your filtered water will taste similar to bottled
water. Most people enjoy the natural flavour. You will immediately notice that brewed coffee and
juices from concentrate have a greatly enhanced taste and aroma.
Q: Where is the system installed?
Typically, the system is installed under the kitchen sink. Some homeowners or installers prefer the
basement or crawlspace, as this conserves storage in the kitchen and may allow for easier access
to the system for maintenance purposes.
Q: Can the WR2 filter system be connected to an extra faucet?
Yes. Many installations will include an optional ¼” line to refrigerator icemakers or additional sink
faucets. See your dealer for advice and parts.
Q: What is the standard warranty with the WR2 filter system?
Every Vectapure II™ system comes with a standard one-year limited warranty on all parts and repair
labour. A detailed warranty card is included with the unit. Normal filter cartridge replacement is
excluded from your warranty.
Q: What is the maintenance schedule for the WR2 filter system?
A good rule of thumb is to replace all filter cartridges every three months. When the old cartridges
have been removed, the system should be purged and flooded with chlorinated water before the
new cartridges are installed.
Section 2. Unpacking and Installation
Your system includes:
Carton Contents
The main filter unit assembly with 2 stages;
One 5-micron polypropylene sediment filter cartridge and one block carbon (or granular
activated carbon) filter cartridge;
One self-piercing cold water supply pipe saddle and valve with cold water tube attached;
One low-lead (stainless is optional) long reach Quick Faucet and mounting hardware, with
tube attached;
Two #10 X1” Wall mounting screws;
One filter housing wrench;
One Owner’s package including this owner’s manual and warranty certificate.

4
Step 1. Selecting the System Location
1. This filter system is designed for installation under a sink. It can however, be mounted
anywhere within 20 feet of the faucet, such as the basement or adjoining utility room. Keep
in mind that filter housings will need periodic replacement and that easy access must be
maintained. Do not install in a location with high humidity, direct sun or a direct source of
heat.
Figure 1.
Mounting bracket
Faucet and mounting hdwe
Supply pipe saddle
Carbon filter cartridge (tube attached)
Sediment filter cartridge
Keep in mind that you may install a tube tee on the line to the faucet to connect icemakers
or other faucets to the system. See your dealer for parts and details.
Step 2. Getting Ready
1. Clear working area. Unpack all components and check for visual damage. Ensure all listed
components are included.
2. Inspect the cold water supply line and the condition of the pipe. The SV-8 saddle included
is intended for standard ½” copper plumbing pipe. If you have a polybutylene, polypropylene,
iron or PVC supply line, you will need to consult your plumber or plumbing supply store to
purchase an appropriate cold water connection.
3. You will need the following tools: An electric drill, a ½” carbide bit, a ¼” carbide bit, a 1/8”
carbide bit, a pencil, a small adjustable (crescent) wrench, a sharp knife (X-Acto type knife
is best), Teflon plumbing tape, adjustable pliers, a rat-tail file, a center punch, a medium flat
head screwdriver, a small household funnel. Always wear eye protection when using an
electric drill.
Step 3. Install the Cold Water Supply Pipe Saddle
1. Turn the water supply line valve to your home OFF.
2. Place the saddle on the COLD water supply line in a place that will not interfere with normal
access to the installation area but within easy reach of the filter unit. Thread the brass
mounting screw through the threaded hole opposite the valve and insert the pipe holding bar,
matching the bar contour with your supply pipe size. Snug firmly but DO NOT
OVERTIGHTEN. Turn the ‘T’ valve stem on the saddle clockwise until the supply pipe is
pierced and the valve is fully closed. Your pipe saddle valve may have the poly tube factory
pre-attached. If the poly tube is not pre-attached, connect the white ¼” tube to the saddle
valve using the compression nut, plastic sleeve (ferule) and tube insert. Snug the

5
compression nut by hand then turn ¼ turn with the adjustable wrench. DO NOT
OVERTIGHTEN. Keep the valve closed for now.
3. You may now turn the water supply to your home ON. Check for leaks around the saddle.
Tighten, reseat or reinstall if necessary.
Step 4. Install the Sink Faucet
A. Quick Faucet Installation (Quick Faucets are standard equipment with Waterite WR2 filter
systems. Dealers may substitute standard faucets in your kit – see Step 4B below for standard-
mount faucet installation instructions.)
Tools required for this step: An electric drill, a 1/8”” carbide bit, a 5/8” carbide bit, a Phillips-head
screwdriver, a center punch, a pencil and a rat-tail file.
1. Examine the sink. If it has an existing hole for mounting a faucet, skip to Step 4A. (5).
2. Locate and mark the spot you wish to install the faucet. Make sure it does not interfere with
operation of the main faucet and that there is clearance for plumbing and mounting hardware
directly below it under the sink or countertop. If you have a stainless sink, go to Step 4A. (4)
3. If you have a concrete, porcelain enamel or ceramic sink, it is strongly recommended that a
professional install the faucet to avoid chipping and damaging the sink finish.
4. Place the Quick Faucet base in the desired location with the inside flat (with the small notch)
facing the direction you wish the faucet to face when installation is complete. Mark the
centres of the mounting screw holes and the center faucet shank hole with the pencil and set
the faucet mounting base aside. Use the center punch to slightly indent the hole centres.
Use the 5/8” bit and drill the center faucet shank hole. Use the rat-tail file to smooth any
burrs or rough edges on the faucet shank hole. Next, use the 1/8” bit and drill the mounting
screw pilot holes.
5. Align the faucet mounting base with the drilled holes in the countertop. Using the Phillips
head screws provided, fasten the mounting base to the countertop., using the 1/16” holes as
pilots. Insert the faucet supply tube in the faucet shank hole and feed it through completely.
Align the locking flat on the faucet base with the mounting base and insert. Turn the faucet
¼ turn to the desired direction. With the Allen key provided in the faucet kit, tighten the
locking screw on the side of the mounting base. It is recommended that you retain the Allen
key for use in the future by taping it to the faucet supply tube under the sink or retaining it in
a safe place.

6
Faucet base mounting screws
Faucet shank
Faucet base
Locking set screw
Quick Faucet mounting base
Faucet supply tube
Figure 2.
B. Standard Faucet Installation (At the request of your dealer, a standard-mount faucet may have
been included in your RO system, instead of the top-mount Quick Faucet. In this case, use the
directions below.)
Tools required for this step: An electric drill, a 5/8” carbide bit, a small adjustable wrench, a center
punch, a pencil, a rat-tail file.
6. Examine the sink. If it has an existing hole for mounting a faucet, skip to Step 4. (6).
7. Locate and mark the spot you wish to install the faucet. Make sure it does not interfere with
operation of the main faucet and that there is clearance for plumbing and mounting hardware
directly below it under the sink or countertop. If you have a stainless sink, go to Step 4. (5)
8. If you have a concrete sink with a thickness of less than 1”, the faucet can be mounted directly
to sink. If the thickness exceeds 1”, the faucet must be mounted directly on the countertop
or a faucet with an extended shank must be used. Tool substitution: Use a 5/8” masonry bit
to drill the concrete sink.
9. If you have a porcelain enamel or ceramic sink, it is strongly recommended that a
professional install the faucet to avoid chipping and damaging the sink finish.
10. Mark the spot chosen for the faucet hole with the pencil. Use the center punch to slightly
indent the spot (the center punch is unnecessary for concrete sinks). Use the 5/8” bit and
drill the hole. Use the rat-tail file to smooth any burrs or rough edges on the hole.

7
11. The sink faucet may now be assembled to the sink or countertop using the assembly
procedure shown in Figure 2. Your faucet may have the poly tube factory pre-attached. If
so, do not connect the tube to anything at this time. If the tube is not pre-attached, do not
attach the poly tube to faucet at this time.
Figure 3.
Standard 1/4” assembly Optional 3/8” assembly
Step 7. Mounting the filter system
1. While holding the system in its mounting position, mark the holes for the wall screws. Using
a 1/8” bit, drill the pilot holes for the screws. Screw in the mounting screws leaving ¼”
protruding. Hang the mounting bracket on the screws and tighten.
2. If the unit is to be mounted on wallboard, use plastic screw anchors, available at any builder’s
supply and follow the manufacturer’s directions.
3. DO NOT INSTALL FILTER CARTRIDGES AT THIS TIME. Spin the filter housing sumps
on to the filter unit and hand-tighten. Use the wrench provided to turn an additional ¼ turn.

8
Step 8. Connect the System Tubing
!
Making and securing a push on connection is simple. First, the
tubing should be cut square and any burrs or rough edges
removed. Insert the tube firmly and push until the tube end
contacts the stop. Gently tug the tube backwards to assure a
secure connection. To disconnect, pull the tube while
pushing in the collet ring. The joint may be used over and over
again, if necessary.
1. Connect the cold water supply valve to the first filter housing water inlet push-on fitting
(marked “water inlet”), after cutting the ¼” supply tube to the length required.
2. Connect the 3/8’” tube attached to the faucet to the system fitting marked “to faucet”. If the
tubing is not pre-attached to the faucet, cut the 3/8” clear tubing to the desired length and
attach the tube to the fitting at the base of the faucet shank to the fitting marked “ to faucet”
on the filter unit.
Step 9. Filling and Sani-Flushing the System
1. Turn on the feed water adapter valve and check all connections for leaks. Do not proceed
further until any leaks are fixed.
2. Open the faucet at the sink and let the water run free for 10 minutes. Turn the saddle valve
OFF. Leave the faucet open until water flow stops.
!
THOROUGHLY WASH HANDS BEFORE LOADING CARTRIDGES.
3. Remove the clear filter housing by turning counter clockwise with the housing wrench
supplied. Remove all protective wrapping from the filter cartridges. Insert the 5-micron white
sediment filter cartridge in the clear housing and reassemble housing. The housings are
seated with o-rings – DO NOT OVERTIGHTEN – 1/4 turn after hand tight is usually sufficient.
Install the carbon cartridge in the remaining white filter housing and reassemble.
Step 10. Starting Up the System
!
DO NOT USE ANY WATER FROM THE SYSTEM UNTIL THE NEXT STEP IS COMPLETE.
4. Open the faucet and let the system operate for about 3-4 minutes. You will see dark carbon
dust briefly flush from the carbon filer cartridge – this is harmless and normal for the first flow
of water through the cartridge. Once completed, your system is ready for use.

9
Section 3: Operation and Maintenance
Operation of your filter system is simple and easy. Be sure to follow the cartridge replacement
schedule to ensure peak performance.
Changing Filter Cartridges and Sani-Purge Procedure
The filter cartridges should be changed, as a rule of thumb, every three months. It is critical that this
be done, to ensure that your drinking water remains fresh. Always purge the complete system at
the same time that the cartridges are changed.
!
THOROUGHLY WASH HANDS BEFORE LOADING CARTRIDGES.
1. Close the cold water supply saddle valve. Open the faucet until the flow of water stops.
Remove the filter housings with the housing wrench and discard the old filter cartridges.
Thoroughly clean the inside of the housing bowls with soap and warm water. Rinse
completely. If the system has been installed with a water supply that does not contain
chlorine, put 2 fluid ounces (60 ml) of common household chlorine bleach such as Javex in
the clear housing. Reassemble filter housings WITHOUT cartridges.
2. Purge Procedure: Open the faucet. Open the raw water supply saddle valve. The filter
housings will now fill with raw and chlorinated water will soon begin to flow from the faucet.
Turn the faucet off and allow the system to stand for about 1 hour.
3. Open the faucet and allow the system to run until a chlorine odour is no longer present. They
system has now been purged and is ready to load the new cartridges.
4. To load the cartridges, repeat Step 9 (3) from the installation instructions above.
Your Warranty
Keep your bill of sale and your warranty certificate, included in this kit. This is needed to claim any
parts or repair service during the warranty period. Read the document completely for warranty claim
instructions.

10
Section 4: Troubleshooting Guide
Trouble Shooting Guide Possible Cause Solution
Low Water or No Water Water supply valve closed
or tank valve closed. Open valves
Crimped poly tube Repair or replace
tube
Filters or membranes plugged Replace filters
Combo filter(s) upside down Install with
rubber gasket up
Tubes installed to wrong fitting Install tubes per
S.8 (1), (2)
Leaking Joints Fittings not seated Disconnect fitting
and reseat tube
Filter housing leaking Tighten with
housing wrench
Inspect o-rings
for cuts or crimps
WR2
RESIDENTIAL FILTER SYSTEMS PARTS LIST
1 2 3 4 5 6
7 89 10 11 12
KEY
DESCRIPTION
PART NUMBER
COMMENT
1
Cartridge 5 mic. sediment
PP1005
All models
2 Cartridge, Carbon
CBC5CTO
or CC5C
All models
3
Filter housing - white
HE1014WWU
4
Filter housing - clear
HE1014CWU
5
Mounting bracket
BK2N1MW
6
Male elbow, push-on, 1/4"
Male elbow, push-on, 3/8”
A4ME4
A4ME6
Cold water side
Faucet side
7
Pressure Reducing Valve
REGP1414E
8
Leak-Stop
LS1414KAD
9
Tube-attached faucet
F9C
Tube attached
10
Plastic housing wrench
HAN06W
11
Connections and O-Rings
12
PE tube - 3/8" (optional)
3636100
Clear

11
WR2
RESIDENTIAL FILTER SYSTEM
FLOW LAYOUT

12
ADDENDUM 1
INSTALLATION INSTRUCTIONS FOR WATERITE P/N REGP1414E PRESSURE
REDUCING VALVE
Residential drinking water RO systems are designed to operate at normal household water
pressure levels, about 50 to 65 PSI. While systems and components are factory tested to
125 PSI, this is to only check for leaks and component integrity. On occasion, some
household line pressures may exceed this normal range and range up to100 PSI. Constant
high pressures exposure may, over time, weaken critical components and lead to leaks or
component failure. Similarly, many households have fast-
acting valves in such places as washing machines,
dishwashers or other appliances. This may cause sudden
hydraulic shock or water hammer conditions throughout the
plumbing system (pipes ‘banging’) that could cause
components or tube to break or rupture.
A well-designed plumbing system usually incorporates shock
arrestors (see figure 1) to soften the effects of water hammer.
Also, most areas where high line pressure exists will require
every home to be equipped with a pressure reducing valve that
lowers the household pressure to a normal range. However,
some household plumbing may not have such safeguards.
Figure 1.
As additional protection for the RO from over-pressure and water hammer, your kit has been
equipped with a combination water pressure reducer and water hammer arresting device,
Waterite p/n REGP1414E. This device is installed on the cold water inlet tube that feeds
the RO system. See figure 2.
Figure 1
Figure 2
!
It is highly recommended that residential RO system installations be made only
in homes where line pressures are at a maximum of 65 PSI and water hammer
arrestors are present.

13
1.0 Install the REGP1414E device
1.1 Turn off the water supply to the cold water supply adapter.
1.2 Using a sharp knife or tube cutter, cut the ¼” tube between the Leak Stop device and
the cold water inlet to the RO system. Make sure the cut is straight and without burrs.
1.3 Insert the tube from the cold water supply adapter into the inlet of the REGP1414E
device. Check the arrow on the device to make sure the flow direction is correct. See
figure 2. Make sure the tube is pushed all the way into the fitting and bottoms out. Tug
on the connection to make sure that it is secure.
1.4 Connect the outlet of the device to the tube leading to the RO. Make sure the tube is
pushed all the way into the fitting and bottoms out. Tug on the connection to make sure
that it is secure.
1.5 Turn on cold water supply and check for leaks. Reinstall tube connections if necessary.
Installation is now complete.

14
ADDENDUM 2
INSTALLATION INSTRUCTIONS FOR LEAK STOP FLOW INTERRUPTOR
Waterite now includes a non-electric leak detection device, with all residential RO systems. This
LEAK STOP is easy to install and will automatically shut off the incoming water being supplied to
the RO unit if any water comes in contact with it.
Simply mount on the floor of the cabinet directly under your RO unit is installed. If a leak occurs on
the RO system, the sensor is triggered and an internal valve closes, preventing water from running
to the RO system and causing water damage.
The LEAK STOP is supplied with a mounting bracket, two-sided tape to make installation easy.
INSTALLATION INSTRUCTIONS
(see Figure 1 below)
For new system installations, installing the LEAK STOP should be your LAST step.
1. Turn inlet water valve off.
2. Using the 2-sided tape provided, place the LEAK STOP in a convenient location under the
RO system, in a place most likely to get wet in the event of a system leak. Make sure the
area is COMPLETELY free of moisture. Remove the tape film and push down firmly so that
tape adheres to surface. (Fig. 1 & 2)
3. Remove the red locking rings from the ports on the LEAK STOP device. (Fig. 3)
4. If desired you can also fasten the bracket directly to the base of the cabinet by using the
screw holes provided on the base of the LEAK STOP. (Fig. 1)
5. From the shut off valve on the main feed line, attach the ¼” (10mm) tube to the inlet side (IN)
of the LEAK STOP device. (Fig 3)
6. From the outlet (OUT) side of the LEAK STOP, connect a ¼” (10mm) tube to the cold-water
inlet of the RO system. (Fig. 4)
7. Make sure all connections are tight and that the tube has been inserted all the way into the
LEAK STOP fittings. Secure the tubing with the locking rings supplied with the LEAK STOP.
(Fig. 4)
8. Turn inlet water valve on. Make sure there are no leaks around the fittings.
Figure 1 Figure 2 Figure 3 Figure 4
Screw mount holes locking clips inlet outlet
WARNING!
The LEAK STOP should be wrapped with a dry towel or cloth before changing cartridges.
This will help avoid it coming into contact with water that may be accidentally spilled in the
process. Should the LEAK STOP device come into contact with any water, the device will

15
be triggered and the tablet will need changing (LEAK STOP refill tablet part number
HDJMF0
REGISTER YOUR PRODUCT ONLINE AT WATERITE.COM OR FILL OUT THE
INCLUDED PRE-PAID, SELF ADDRESSED POSTCARD.

16
WATERITE, INC.
Winnipeg, Manitoba
Canada
www.waterite.com