Waters Magnet+ User manual

USER MANUAL
Magnet+
Copyright © 2021 Waters Corporation

Magnets can aect pacemakers
The magnetic eld near the magnets can aect pacemakers,
ICDs and other implanted medical devices.
Many of these devices are designed to deactivate in a
magnetic eld. Care must be taken to avoid inadvertently
deactivating such devices.
Safety instructions
• The device must always be completely switched o (cables
removed) before moving it.
• The device must be handled with caution as it contains
moving parts.
• The user must maintain a distance of at least 20cm from the
product (WiFi antenna) while it is being installed and operated.
• The device is intended for indoor use only.
• Device maintenance has to be done exclusively by an Andrew
Alliance representative.
• If the device is used in a manner not specied by the manufac-
turer, the protection provided by the device may be impaired.
• All the input/output ports are Safety Extra Low Voltage (SELV)
circuits. SELV circuits should only be connected to other SELV
circuits.

Power socket
Ethernet for
cable connection
LED indicator
Open hatch
from here
Built-in
computer
Built-in wireless
adapter
Labware holder
Labware holder
of other devices
About this manual
Read the user manual before using this device. Strictly follow usage and main-
tenance instructions provided in the manual. It is the user’s responsibility to
become familiar with all available information concerning the correct use, care
and limitations of these products. If you are uncertain about the correct use or
limitations of the products, contact Andrew Alliance service and support. The
manufacturer, the distributor and their respective owners, employees, agents and
representatives are not responsible or liable for errors or omissions.
Information in this User Manual is subject to change without notice and does
not represent a commitment on the part of Andrew Alliance. Andrew Alliance
assumes no responsibility for any inaccuracies that may be contained in this User
Manual. Andrew Alliance makes no commitment to update or keep current the
information in this User Manual, and reserves the right to make improvements
to this User Manual and/or to the products described in this User Manual, at any
time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
Product
overview
Power button

Getting started
Plug your Magnet+
into a power source.
Wait for the LED indicator to
turn blue and blink.
After a couple of mi-
nutes, the Magnet+ will
inform you when it is
in installation mode.
Connect your computer, tablet or smartphone to the Magnet+
Launch a web browser, type http://192.168.2.1
and follow the on-screen steps to continue installation.
A. Go to your Wi-Fi settings
and select the network named Magnet-5xx.4xxx.xxxxx
12
3
4
scan me
xxxx.xxxxx is the Magnet+ device serial number (you can nd it on top of your
device)
B. The LED indicator will stop blinking when it’s successfully connected.
Magnet-5xx.4xxx.xxxxx
If the Magnet+ doesn’t automatically
enter installation mode, press the power
button 5 times.
!
http://192.168.2.1
Before
you begin
If you do not have a OneLab account, please create one by going to:
https://onelab.andrewalliance.com/signup
The device will automatically start up.
Only use the provided AC/DC
power supply unit and cords.
Please note that the
installation page might
open automatically.
If you do not have access to a
Wi-Fi compatible device, please
refer to our online help:
help.andrewalliance.com
!
!

of
45 steps
1
1:46:37
No additional guidelines
Simultaneous activity
None
Stop vortexing
Next step
I've made a mistake...
Continue
AbortStep list
Experiment ongoing: Bead purification protocol - 076
Wait for the beads to pellet…
01:20
Beads
pelleting
Magnet+ - 933.3939.XXX
Magnet+
Applying magnetic field…
Sample
tube 293
Operations
Design your protocol
Execute experiment with
Magnet+
Start the experiment and let OneLab
control your device
Our drag-n-drop editor makes it easy to
design a precise and complete protocol
with all that you need to run your
experiment perfectly.
Create an Apply magnetic eld
action by clicking on this menu,
which is located in the left of the
screen.
Follow the visual instructions based on the
protocol being used and you will be guided
through your experiment.
Each step of the experiment will be recorded
and available in OneLab.
Actions
Apply magnetic
field
OneLab will automatically select your
Magnet+ and allows you to use it with every
available experiment set-up, either manual,
semi-automated or fully automated operation.
Choose your desired experiment setup and
then prepare all the required materials.
Feel free to contact
the Andrew Alliance
support team Send us an email to
[email protected]
Chat with our support team
directly in OneLab
We reply within 1 business day

Technical data
Labware
compatible
Check the OneLab Domino Catalog
at andrewalliance.com/
domino-catalog
Relative humidity 80% at 37°C
Maximum
operating altitude
2000 m
Environment
temperature
operating range
+4 to +37°C
User interface Through OneLab software
Ingress protection IP20*
Dimensions
(W x L x H)
170 x 162 x 115 mm
(The specied dimensions are
subject to change according to the
labware)
Weight 1.65 kg
External power
supply
Input 100-240 VAC, 1.4 A
/ output 24 VDC, 5 A, 120 W
Power or
current rating
5 A
Overvoltage
category DC port
Cat I
Operating voltage 24 VDC
Network
connectivity
• Gigabit Ethernet
• Wi-Fi 2.4 GHz and 5 GHz
Pollution degree
of the intended
environment
Pollution degree 2
Cleaning Only with a wet tissue or isopro-
panol
Warranty 1 year
Certication CE, FCC, RoHS, WEEE
1. Place your connected
devices as indicated by
OneLab.
2. Open the hatches.
3. Plug the power cables
into your devices power socket.
4. Pass the cables in front of devices and then
insert them into the dedicated path.
5. Close the hatches.
Multiple connected devices
installation
Operating device
Power on
Power o
When the device is in standby mode
(plugged to power source but turned
o), press the power button to turn
on the device.
Note: The device will automatically
start up when you plug it to a power
source.
When the device is in its idle state
(no experiment running), press the
power button for 5 seconds to turn
o the device.
5s
*Avoid spilling liquid on the device.

Unit end of life
When a unit reaches the end of its useful life, contact Andrew Alliance for
directions and information on the end-of-life policy.
This is in accordance with the European Union Directive 2002/96/EC on
Waste Electrical and Electronic Equipment (WEEE).
Certications
Electrical safety
EMC
RADIO
FCC
RoHS
I. IEC 61010-1: 2010
II. IEC 61010-1/A1: 2016
III. UL 61010-1:2012
IV. CAN/CSA 22.2#61010-1-12
I. EN 61326-1: 2013
II. EN 301 489-1 V2.2.0
III. EN 301 489-17 V3.1.0
I. EN 300 328 Ver 2.1.1
II. EN 301 893 V2.1.1
I. FCC 47 CFR part 15 subpart B section 15.107 (b) and section 15.109 (b and g)
Class A all over other device tested per ANSI C63.4 (Ed. 2014) procedures
II. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired opera-
tion.
RoHS 3 (EU) 2015/863

Waters Corp
34 Maple Street
Milford, MA 01757
USA
Phone: [phone]
Andrew Alliance S.A.
(Headquarters)
Chemin Grenet 21
1214 Vernier (Geneve)
Switzerland
Phone: [phone]
[email protected]
Part number: 518.005.2 | 2021 © Andrew Alliance - A Waters Company.