WE-EF FLA730 LED User manual

Safety Notice
The manufacturer is discharged from liability when damage
is caused by improper use or installation.
If any luminaire and/or accessory is subsequently modi-
fied, the persons responsible for the modification shall be
considered as manufacturer.
FLA730 LED_260722 / 006-1324
Technical specifications are subject to change.
© WE-EF 2022
we-ef.com
WE-EF LIGHTING USA
Tel [phone]
[email protected]
WE-EF LIGHTING
Installation and
Maintenance Instructions for
Asymmetrical Area
Floodlight
FLA730 LED

Asymmetrical Area Floodlight
IP66, IK08
16.14
9.84
12.6
0
1.73
ø 0.433
ø 0.709
ø 0.433
5.51
Light source
12 LED 24W / 18 LED 36W / 12 LED 36W /
18 LED 54W*
Nominal power, for latest data refer to
www.we-ef.com
Class I, II, ta = 25 °C
Mounting height ................... 11.5 – 20 ft
Windage area: ................... max. 0.484 ft2
Weight ................................ 21.2 lb
120-
277 V
Notice
In case the luminaire is equipped with an optional
available surge protector, the function can get
tested if the signal LED is lit green when the supply
voltage is turned on.
In case the surge protector is defective, the LED
device gets automatically disconnected from the
mains supply. If the signal LED is not lit, the lumin-
aire is not functioning.
FLA730
Ø0.197 –0.472 in 16 AWG
Installation
The product must be installed and maintained by
a suitably qualified professional in compliance with
latest building/construction and/or electrical regu-
lations and relevant legislation.
Attention: Do not open luminaire while mains
supply is switched on.
Notice: If the luminaire is modified by anybody
other than the original manufacturer, then the
warranty will no longer be valid and shall become
the full responsibility of the modifying person/
organisation. Claims based on defects attributable
to improper installation and/or application, and the
consequences thereof, are excluded.
In case of component failure, LED replacement
due to abnormal circumstances or at end of life,
replacement must be carried out by a suitably qua-
lified and trained professional.
In case of questions please contact our technical
hotline: [phone] (from Monday - Friday
from 08.00 until 16.00 hours).
Maintenance
Apart from cleaning the product’s exterior surfaces,
no special maintenance work is required. Do not
use high-pressure cleaners.
Protect our environment: Discard used LEDs in
compliance with the most recent environmental
legislation.

5) Firmly tighten cable gland F.
6) Put in gear-tray, close plug connection Dand
close gear-tray. Make sure that the gear-tray is
firmly shut.
7) Close frame Aand firmly tighten screws B.
8) Install the bracket Gto the floodlight by using
the two knurled head screws Hand the allen
screw I.
9) The fastening of the floodlight to the pole
depends on the type of chosen bracket. Make
sure that the floodlight is installed to the bra-
cket with two M10 screws and self-locking nuts
made of stainless steel.
Installation Procedure
Luminaire prewired, do not open!
1) Switch off the mains electrical supply.
2) Loosen screws Band open frame A.
3) Unlock shutter Cand turn down the gear-tray,
disconnect plug connector D and remove the
gear-tray.
4) Cut the connecting cable Xcorresponding to
the height of the pole and insert it through the
cable gland Finside the luminaire.
Connect the neutral conductor (N), phase (L1)
and the earthing to the corresponding mar-
ked contacts of the terminal clamp D.
Compare the local voltage and frequency with
the data mentioned on the label of the luminaire.
IG
C
D
II
B
A
HF
X
G