WE-EF FLB141 1 LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance with
applicable standards.
For comprehensive protection of a luminaire installation against lightning and
electrical surges, it is essential to cover mains supply and data input lines at
the distribution board level, by using respective primary (Type 1) and secondary
(Type 2) surge arrestors in compliance with EN61643-11/IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and activated
prior to luminaire installation. Also, disconnect luminaires before operating
high-power devices such as, for example, electrical arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained in this
document for details.
WE-EF LEUCHTEN
Installation and Maintenance
Instructions
Floodlight
FLB141 #1 LED

1
Floodlight
FLB141 #1
IP66, IK08. Class I. ta = 40°C
Weight kg
for FLB141 #1 LED 3.1
Windage area m²
for FLB141 #1 LED 0.038
Orientation: all directions
Mounting Accessories
Flat surIace Ƃtter
SF-FLD1 for FLB141 #1 145-9535
ColuPn Ƃtter
CF-FLD1 for FLB141 #1 145-9536

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces, no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried out
E\DVXLWDEO\TXDOLƂHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a
VXLWDEO\TXDOLƂHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and
relevant legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire.
Notice:,IWKHOXPLQDLUHLVPRGLƂHGE\DQ\ERG\RWKHU
than the original manufacturer, then the warranty will
no longer be valid and shall become the full respon-
sibility of the modifying person/organisation. Claims
based on defects attributable to improper installation
and/or application, and the consequences thereof, are
excluded.
The installation on site must comply with local and/or
national health and safety regulations.

4
1) Switch off mains electrical supply.
Installation Procedure
Installation tFlat surIace Ƃtter
3) FeedcableAfrom luminaireBthroughpivot and
 KROHRIƃDWVXUIDFHƂWWHUC.
 'HWHUPLQHSRVLWLRQVIRUƂ[LQJVFUHZVD. Drill
relevant holes Eand insert nylon plugs. Insert
and tighten screws D.
Warning: Ensure not to damage any electrical
cable, water pipe or other items drilling holes.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLB141-LED 220-240V50-60/Hz
161-XXXX SOE XXXXXXX
LED 3000K 18W item no. XXX
07/18 IP66

5
5) Loosen screws F6OLGHVOLSƂWWHURYHUSLYRW
while pulling cable Athrough hole.
8) Loosen screw G. Aim luminaire in desired
direction and tighten screw G.
6) Turn luminaire towards object to be
LOOXPLQDWHG(QVXUHVOLSƂWWHULVSURSHUO\
seated on pivot, then tighten screws F.
7) Connect cable Awith mains supply cable.
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).

6
1) Switch off mains electrical supply.
Installation - ColuPn Ƃtter
6XLWDEOHIRUFROXPQGLDPHWHUŰPP
6HUYLFHGRRURQFROXPQKDVWREHSURYLGHGIRUFDEOHWHUPLQDWLRQPD[LPXPPIURPFROXPQƂWWHUPRXQWLQJSRVLWLRQ
3) Drillscrewholes Aand cableentry hole Bon
column.Ensure cableentry hole BKDVVXIƂFLHQW
diameterto feedcable fromluminaire.
 6HWDQGƂ[FROXPQƂWWHUCin position. Insert and
tighten screws D
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLB141-LED 220-240V50-60/Hz
161-XXXX SOE XXXXXXX
LED 3000K 18W item no. XXX
07/18 IP66

7
5) Loosen screws F. Feedcable Dfromluminaire
Ethroughpivotand cable entryhole B.
Connectluminaire EZLWKFROXPQƂWWHUCby
VOLGLQJVOLSƂWWHURYHUSLYRW
8) Loosen screw G. Aim luminaire in desired
direction and tighten screw G.
6) Turn luminaire Etowards object to be
LOOXPLQDWHG(QVXUHVOLSƂWWHULVSURSHUO\
seated on pivot, then tighten screws F.
7) Connect cable Dwith mains supply cable.
a) ON/OFF (L = Phase, N = Neutral,
= Earthing)
b) 1-10 V/DALI (L = Phase, N = Neutral,
= Earthing, DA/DA = DALI control line,
D–/D+ = 1-10 V control line).

www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
LQIRDVLDSDFLƂF#ZHHIFRP
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
TO9250W0519 © WE-EF 2019
7HFKQLFDOVSHFLƂFDWLRQVDUH
subject to change.