WE-EF FLB141 #2 LED User manual

Surge Protection
This product features built-in surge protection circuitry in compliance
with applicable standards.
For comprehensive protection of a luminaire installation against lightning
and electrical surges,it is essential to cover mains supply and data input
lines at the distribution board level,by using respective primary (Type 1)
and secondary (Type 2) surge arrestors in compliance with EN61643-11/
IEC61643-1.
Warning
Ensure that all required surge protection measures are in place and
activated prior to luminaire installation.Also,disconnect luminaires
before operating high-power devices such as, for example,electrical
arc welders.
Do not open during installation
This product is factory-sealed.
Refer to the instructions contained
in this document for details.
WE-EF LIGHTING
Installation and Maintenance
Instructions
Floodlight
FLB141 #2 LED

1
Floodlight
FLB141 #2
IP66, IK08. Class I. ta = 40°C
Weight lb
for FLB141 #2 LED 8.4
Windage area ftə2
for FLB141 #2 LED 0.545
Orientation: all directions

2
Light Source
LED
Maintenance
Apart from cleaning the product’s exterior surfaces,no special maintenance work is required.
Do not use high-pressure cleaners.
In case of component failure due to abnormal circumstances or at end of life, replacement must be carried
RXWE\DVXLWDEO\TXDOLĥHGDQGWUDLQHGSURIHVVLRQDO
Warning: Do not open luminaire while mains supply is switched on.

3
Installation
The product must be installed and maintained by a VXLWDEO\TXDOLĥHGSURIHVVLRQDOLQFRPSOLDQFHZLWKODWHVW
building/construction and/or electrical regulations and relevant legislation.
Warning: 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\SULRUWRLQVWDOOLQJDQGFRQQHFWLQJWKHOXPLQDLUH
Notice:,IWKHOXPLQDLUHLVPRGLĥHGE\DQ\ERG\RWKHUWKDQWKHRULJLQDOPDQXIDFWXUHUWKHQWKHZDUUDQW\ZLOO
no longer be valid and shall become the full responsibility of the modifying person/organisation.Claims
based on defects attributable to improper installation and/or application, and the consequences thereof,
are excluded.
The installation on site must comply with local and/or national health and safety regulations.
Important: When mounting luminaires on concrete or surfaces containing limestone content, WE-EF
recommends using mounting accessories – a short post or a ground spike to prevent galvanic corrosion.
In areas where mounting accessories are not applicable, ensure the luminaire’s aluminium base is separated
from concrete and limestone using a plastic or rubber sheet. Allow concrete to cure before installation –
DO NOT INSTALL ON WET CONCRETE!
Handling:(QVXUHWKHPRXQWLQJĦDQJHSODWHVDUH
handled with care,scratches and damage to the coated surface can result in galvanic corrosion.
A WE-EF warranty does not cover any adverse reaction or damage,due to improper installation and
requests that our recommendations are followed.

4
 6ZLWFKRĪPDLQVHOHFWULFDOVXSSO\
Installation Procedure
 6HSDUDWHPRXQWLQJĦDQJHAfrom junction box
mounting plate Hby removing fasteners D.
Mount plate over junction box with mains
supply cable G.
Warning: Ensure not to damage any electrical
cable, water pipe or other items during
installation.
 5HPRYHPRXQWLQJĦDQJHAby loosening
screws B.
2) Check that rating shown on luminaire label
conforms with mains electrical supply.
(example)
FLB141-LED 120-277V / 60Hz
161-XXXX SOE XXXXXXX
LED 3000K 18W item no.XXX
07/18 IP66

5
5) Feed mains supply cable Gthrough the
junction box mounting plate I,while setting
PRXQWLQJĦDQJHALQSRVLWLRQ7Rĥ[PRXQWLQJ
ĦDQJHA, insert and tighten screws D.
7) Loosen screws Mslightly.Aim luminaire in
desired direction, retighten screws M.
6) Ensure that all surface are clean and dry.
3RVLWLRQOXPLQDLUHRYHUPRXQWLQJĦDQJHA
and make electrical connections (L= Phase,
N = Neutral,G = Ground, D+/Dŝ= 0-10 V) C.
Turn luminaire towards object to be illuminated.
Tighten screw B.

www.we-ef.com
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[email protected]
TO9249W0522 © WE-EF 2022
Technical specifications are
subject to change.