WE-EF PFL230 User manual

WE-EF LEUCHTEN
Installation and
Maintenance Instructions for
Post Mounted Luminaire
PFL230 LED
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST

1
Post Mounted Luminaire
Installation
The product must be installed and maintained by a suitably
qualified professional in compliance with latest building/
construction and/or electrical regulations and relevant
legislation.
Warning: Switch off mains electrical supply prior to
installing and connecting the luminaire. Do not open lumi-
naire while mains supply is switched on.
Notice: If the luminaire is modified by anybody other than
the original manufacturer, then the warranty will no longer
be valid and shall become the full responsibility of the
modifying person/organisation. Claims based on defects
attributable to improper installation and/or application, and
the consequences thereof, are excluded.
In case of component failure, LED replacement due to
abnormal circumstances or at end of life, replacement must
be carried out by a suitably qualified and trained professional.
Lamps
12 LED 12W / 18 LED 18W / 12 LED 24W / 18 LED 36W*
*Nominal power, for latest data refer to www.we-ef.com
Protection: IP66 / IK08
Class I, II, ta = 25°C
Mounting height: . . . . . . . . . . 3,5–6,0 m
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . 9,6 kg
Wind age area: . . . . . . max. 0,042 m²
410
250
140
Ø 5,5 - 12 mm
2,5 mm2
In case of questions please contact our technical hotline:
[phone] (from Monday - Friday from 08.00 until
16.00 hours.

2
Notice: In case the luminaire is equipped with an optional
available surge protector, the function can get tested if the
signal LED is lit green when the supply voltage is turned on.
In case the surge protector is defective, the LED device
gets automatically disconnected from the mains supply.
If the signal LED is not lit, the luminaire is not functioning.
with the most recent environmental legislation.
Protect our environment: Discard used LEDs in compliance
pressure cleaners.
special maintenance work is required. Do not use high-
Apart from cleaning the product’s exterior surfaces, no
Maintenance
conductor (N), phase (L1) and the earthing to the
cable gland F inside the luminaire. Connect the neutral
of the pole and insert it via the bracket E through the
Cut the connecting cable X corresponding to the height4)
nect plug connector D and remove the gear-tray.
Unlock shutter C and turn down the gear-tray, discon- 3)
2) Loosen screws B and open frame A.
1) Switch off the mains electrical supply.
Installation Procedure
required).
code to download app to mobile device (iOS or Android
required to commission or control luminaires, scan QR
For DALI CASAMBI applications,4remote BTapp is9)
the six hexagon socket screws G.9
naire in position. Secure luminaire by evenly tightening
Feed cable through top of column, while setting lumi- 8)
Close frame A and firmly tighten screws B.7)
gear-tray. Make sure that the gear-tray is firmly shut.
Put in gear-tray, close plug connection D and close the 6)
install the bracket E to the luminaire.
Firmly tighten cable gland F, fasten the conduit and 5)
mentioned on the label of the luminaire.
Compare the local voltage and frequency with the data
cable has to be double insulated according to class II.
Class II: No protection earth is required. The power
clamp D.
corresponding marked contacts of the terminal


3
D
E
G
F
X
C
B
A

DS98L SERIES
DS98L-120 DS98L-230 DS98L-400
DS98L-230G/2L
120 Vac L+N
230 Vac L+N
230 Vac 2L+N
TT/TN
TN
*values per pole
6500 ft max.
2000 m max.
-40/+85°C max.
-40/+185°F max.
IP20
indoor use only
P/N
ISCCR*
IPE
Imax*
10 kA
10 kA
0 mA
Uc (Vac) 150 275
AC Network
AC System
Characteristics
ATTENTION !
- Installation must be performed only by electrically
skilled operator.
- National electrical installation rules must be followed.
- The unit must be used only as surge protector and
according the conditions described in this document.
- Surge protectors must be selected in relation with an
dedicated AC network (see Table 1)
- Dedicated fuses must be installed in the surge
protector branch (see Table 2).
- In case of red indicator, the surge protector must be
replaced.
GB
Wiring
F1
SPD
F1 ≤ 8 A for DS98L-xxxG/2L
EQUIPt
EQUIPt
L1
I L2
DS98L-xxxG/2L
N
N
L1
L2
LINE
EQUIPt
Technical Data
In-line wiring (recommended)
3

Maintenance
Application example
4
10 mm
0.4 in
10 mm
0.4 in
#20-13 AWG
0.5-2.5mm²
1
Clip on
symmetrical
DIN rail
3
0.5 Nm
4.4 Lb-In
2
N
L
Switchboard
F1
optional
PE
PE
0.5-2.5mm²
#20-13 AWG
X
Green LED ON + AC ON = OK
Green LED OFF + AC line OFF = Defect
DS98L
La
Lb
Nb
Na
2
1
Installation
and replace
with
DS98L-xxxG/2L
If the Luminaire is supplied with a Citel
MLPC-230L-V, please refer to the
instructions supplied with the device
Attention

6
WE-EF LIGHTING
Thailand
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
Australia
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United States of America
Tel [phone]
Fax [phone]
[e-mail]
www.we-ef.com
WE-EF LEUCHTEN
Germany
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LUMIERE
France
Tel [phone]
Fax [phone]
[e-mail]
WE-EF HELVETICA
Switzerland
Tel [phone]
Fax [phone]
[e-mail]
WE-EF LIGHTING
United Kingdom
Tel [phone]
Fax [phone]
[e-mail]
Sicherheit
Der Hersteller übernimmt keine Haftung für Schäden, die durch
unsachgemäßen Einsatz oder Montage entstehen.
Werden nachträglich Änderungen an Leuchten und/oder Zubehör
vorgenommen, so gilt derjenige als Hersteller, der diese Änderun-
gen vornimmt.
Safety indices
The manufacturer is then discharged from liability when damage is
caused by improper use or installation.
If any luminaire and/or accessory is subsequently modified, the
persons responsible for the modification shall be considered as
manufacturer.
INSTALLER
HOTLINE
[phone]
7am – 7pm AEST
© WE-EF 2021
specifications are subject to change.
Technische Änderungen vorbehalten.Technical
PFL230_R.SPD_LED_REV1_040221