Wellis Cosmo ACS0206 Manual

EN Cosmo shower mixer
Instruction guide
DE Cosmo dusch mixer
Aufbauanleitung
FR Mélangeur de douche Cosmo
Guide d’installation
HU Cosmo zuhany csaptelep
Szerelési útmutató
RO Baterie duŞCosmo
Instrucţiuni de montare
ACS0206

|2 ||EN |
Cosmo bath mixer
Do not
disassemble! Flush
the pipe!
List of the standard accessories
Please double-check the accessory list hereinaer and contact our company or our distributor for
any unconformity.
Remarks:
– Without aecting their performancing, accessories may be changed without further notice;
– Drawings for reference only, Product size & shape refer to actual faucet!
Installation Instructions
1. Do not disassemble the main body, as it has been installed & commissioned correctly &
precisely before leaving the factory!
2. To avoid the faucet from jamming, do ush the water pipe before installation!
3. Aer installation, make sure every joint safely sealed & no
leaking!
4. Using condition: Working pressure at 0.05-1.0 MPa
(including cold & hot water pressure), with applicable water
temperature: 4 °C-90 °C.
5. Make sure to connect the hot/cold inlet pipe correctly, if
standing in front, hot water pipe connecting to the le & cold
water pipe connecting to the right!
Code The Accessory list Quantity
1Main body 1
2O-ring 2
3Flange 2
4Eccentric nut 2

|EN ||3 |
The operation of our shower panels and faucets is designed for the ideal water pressure
between 3.5-4.5 bar.
Cleaning & Maintenance
To keep the product clean & shining, follow the as below:
1. Flush with clean water & dry with soft cloth only!
2. If any dirt, clean with soft liquid or transparent glass detergent!
3. Do not use any scrubbing detergent, polisher, sane-cloth, paper tissue or scraper!
4. Do not use acid detergent, indissovable grain-like detergent or soap!
Usage
How to operate the handle
– Raise the handle up for opening water; push it
down for close!
– Turn the handle to the le to increase hot water
ow for higher water temperature, and lower
water temperature by operating reversely!
Installation Procedures
Please install the connection hose into the wall according to the installation Procedures.
Cold
connection
hose
Hot
connection
hose Sealed
tape
Water
heater
Le
hot
water
Right
cold
water
Open
Close

|4 ||EN |
Important!
– The temperature of the water that is in contact with the product and intended for human
consumption must not exceed 65°C for health reasons.
– Use: domestic hot water supply.
– Aer installation and before the rst use, as well as if used regularly, it is advisable to rinse
the product before consumption. Aer the installation, we recommend rinsing the product for
5-5 minutes with cold, respectively hot water. It is necessary to run at least 1-2 litres of water
before consumption. The water obtained during the rst rinse should not be used for cooking or
as drinking water.
– Considering that hot water increases metal solubility, it is recommended to use cold water for
drinking and heat it up when used for cooking.
– The exible tap connectors used for connecting the products must be registered products.
– It is recommended to descale and disinfect the shower head of the faucets on a monthly
basis. For the purposes of cleaning and disinfecting the faucets, only chemicals that meet the
requirements of Gov. Decree 201/2001. (X.25) and Joint Decree 38/2003. (VII.7) ESzCsM-FVM-
KvVM should be used.
– Due to its principles of operation, the shower head creates signicant amount of aerosol, thus
posing an increased risk of Legionella exposure. Therefore its use is not recommended in the
rooms of healthcare facilities, or any other location where the number of Legionella colony
forming units/liter in the cold and/or domestic hot water reaches the limit determined in
Ministerial Decree 49/2015 (XI. 6.).

|DE ||5 |
Cosmo dusch mixer
Nicht
zerlegen! Wasserleitung
sspülen!
Liste der standard zubehöre
Bitte überprüfen sie die Zubehörliste zwei mal und Kontaktieren sie unsere Firma oder unseren
Lieferant, falls es einen Fehler gibt Bemerkungen:
– Zubehöre können ohne Benachrichtigung ersetzt werden, ohne dass ihre Performanz beeinußt
wird.
– Die Zeichnungen dienen lediglich zu informativen Zwecken. Die Größe und die Form des
Produkts beziehen sich auf den tatsächlichen Wasserhahn!
Installationsanleitung
1. Hauptteil nicht abbauen, da es bevor der Lieferung richtig und genau installiert und beauragt wurde!
2. Um Verstopfung des Wasserhahns zu vermeiden, spülen Sie bitte vor der Installation die
Wasserleitung!
3. Achten Sie nach der Installation darauf, dass jede Fuge sicherversiegelt ist und es keinen
Austritt gibt!
4. Nutzungsbedingungen: Arbeitsdruck von 0.05-1.0
MPa (einschließend Kalt- und Warmwasserdruck), mit
einsetzbarem Wassertemperatur: 4 °C- 90 °C.
5. Achten Sie drauf, dass das kalte/warme Einlaufrohr richtig
angeschlossen wird; wenn man davor steht, wird die warme
Wasserleitung auf der linken Seite verbunden und die kalte
Wasserleitung auf der rechten Seite!
Code Zubehörliste Anzahl
1Hauptkörper 1
2O-Ring 2
3Flansch 2
4Exzentermutter 2