Wellis CORSICA BLACK WF00073 Manual

Corsica Black Floor Standind Toilet Tank
For wall-mounted toilet - INSTRUCTION GUIDE
Corsica Black bodenständiger spülkasten
für wandmontierte Toiletten - BEDIENUNGSANLEITUNG
Réservoir de toilette posée au sol de Corsica Black
Pour les toilettes posées au sol - MODE D´EMPLOI
Corsica Black álló wc-tartály falraszerelt wc-hez
SZERELÉSI ÚTMUTATÓ
EN
DE
FR
HU WF00073
CORSICA BLACK

Accessories List
. ...............................................................................
................................................................................
.........................................................
................................................................................
.........................................................................
.....
1
2
4
5
6
14
Content
Technical Specifications
Technical drawing, inlet valve & flush valve connection
Cistern installation
Maintenance & daily care

Quantity
Specification
Names
Accessorieslist Quantity Names
Item List Specifications
rubber seal
white air
hose
blue air hose
toilet mat
flush pipe
rubber seal on
above pipe
pipe
connection
straight flush
pipe
rubber seal
expansion nut
small
washer
M12 bolt
decorative cap
M12 nut
big washer
rubber sleeve
decorative cap
base
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
Ø110
Ø60
Ø22*2.0
Ø32.5*2.5
screw
white
blue
2
eccentric pipe
Accessories List
1
steel
expansion bolt 2
expansion nut washer
22
screw 2
ST4.8*45
8*40 Ø11*1.2
ST6.8*67
SX10 Ø6-8

3
Alumunium frame Glass panel Flush valve Inlet valve
Push button Screw set
Cistern
Lever
Drainage eccentric pipe
Accessories list
Half height frame

4
Technical Specitication
Name
Model
Ambient temperature
Water supply pressure
Water supply temperature
Dimension
Technical Specitication
3~40°C
4~35°C
1003.5mm X 483mm X 108mm
0.07~0.75MPa
CJ805W+J518
Pneumatic cabinet cistern for wall-hung WC

5
Ø100~110
180±15
022 ~062
05±002
Technical drawing, inlet valve & flush valve
connection
483
1003.5
240
375
35
180
230
98.5
98.8
108

1
3
6
Insert the drainage pipe into the
drainage hole on the wall
Lean the whole cstern to the wall
and align the flush pipe position
with the buckle
240
2
Cistern installation
Hook on the back
plate
Open the cistern top
cover, pull and
separate the hose
from the hook.

Ø 8 Ø 10
5
7
As indicated by the arrows mark
the 4 points on the wall and 2
points on the ground accordingly.
Drill the holes according to the marked poin ts (the
holes' depth must be deeper than the length of the
expansion nut, the diameter shown as in the picture)
and press the corresponding expansion nut into the
hole.
7
Lean the whole frame onto the right
position of the wall.
Then move away cistern
Ø8 Ø8
Ø10 Ø10
Ø10
Ø10
6

13mm
4
Buckle the hose onto the hanger again, and
connect the hose to the stop valve on the
wall.
Open the stop valve on the hose
to see whether it works and water
runs into cistern tank
8
23mm

5 6
9
Push button
Push button
frame
Install the push button frame and
button onto the glass
Insert the two plugs into the
positions as shown
Hang hook on
the panel
(4pcs)
Install the panel, make sure the glass
panel close to the alumunium frame,
then push down the panel until the
hung hook totaly into the fasteners
on the frame.

7
8
10
Connect air hoses to the correct positions
Blue air hose
White air hose
Half flush mark
Full flush mark
Assemble the top cover back to the
cistern frame
Install the cistern top cover.
Hook on the cover Fastener
Top cover
Align
Hook and
fastener should
be totaly locked.

9
1 2 3 4
1234
11
Cut the flush pipe and drainage pipe
Mark on the straight flush pipe and
drainage pipe

5
10
12
Screw the bolts into the cistern
frame
Install toilet mat
Install the straight flush pipe into
the cistern
Install the flush pipe into the toilet
Install toilet

6
7
13
Cut off extra part of the toilet mat
Test half & full flush functions

14
23mm
Remove the top cover
Turn off the stop valve on the
flexible hose
Separate the hose from the stop
valve
Take out the inlet valve upwards
Maintenance & daily care
1.1 Inlet valve removal

15
23mm
Adjust the float upwards to increase the inlet
volume; or downwards to reduce the volume
Remove the water-stopping part
Wash this removed part
1.2 Inlet valve adjustment & clean 1.3 Inlet valve installation

16
Remove the air hoses from the
air hose holes
Remove the lever
2.1 Flush valve removal
blue air hose
white air hose

17
Buckles on the cistern hunging
plate
Opening the buckles on the cistern hunging plate and lift upwards the
flush valve

18
Float
Adjust the float upwards to reduce the flush volume;
or downwards to increase the volume
Washer
Cover
Rubber seal
Cover
Clean the washer
Remove the cover, washer and rubber seal by
rotating counterclockwisely the cover around 90°
2.2 Flush valve adjustment & clean

19
“click”
Flush valve base
Install the flush valve downwards into the cistern
body(Remark make sure the flush valve bottom is
aligned with flush valve base. And please make sure
flush valve is installed in the shown direction during
installation.
Re-install the lever
Install the top glass cover
Press the flush valve until it
clicks in the correct position.
2.3 Fush valve installation