Wenglor IR 00 Series User manual

IRxx00x
Inductive Ring Sensor
Operating Instructions
Translation of the original operating instructions
Subject to change without notice
Available as PDF file only
Version 1.0.0
As of: 7/04/2023
www.wenglor.com
EN

2Table of Contents
Table of Content
1. General ........................................................................................................................................................4
1.1 Information Concerning these Instructions ..........................................................................................4
1.2 Explanations of Symbols......................................................................................................................4
1.3 Limitation of Liability.............................................................................................................................5
1.4 Copyrights............................................................................................................................................5
2. For Your Safety ..........................................................................................................................................6
2.1 Use for Intended Purpose....................................................................................................................6
2.2 Use for Other than the Intended Purpose............................................................................................6
2.3 Personnel Qualifications ......................................................................................................................6
2.4 Modification of Products.......................................................................................................................6
2.5 General Safety Precautions.................................................................................................................7
2.6 Approvals and Protection Class...........................................................................................................7
3. Technical Data ............................................................................................................................................8
3.1 General Data........................................................................................................................................8
3.2 Housing Dimensions............................................................................................................................9
3.3 Connection Diagram ..........................................................................................................................10
3.4 Complementary Products ..................................................................................................................11
3.5 Control Panel .....................................................................................................................................11
3.6 Scope of Delivery...............................................................................................................................11
4. Transport and Storage .............................................................................................................................12
4.1 Transport............................................................................................................................................12
4.2 Storage ..............................................................................................................................................12
5. Installation and Electrical Connection....................................................................................................12
5.1 Installation..........................................................................................................................................12
5.1.1 Installation Using the Soft Binder ...........................................................................................13
5.1.2 Other Installation Options.......................................................................................................14
5.1.3 Installation Instructions ..........................................................................................................14
5.1.4 Smallest Recognizable Object ...............................................................................................15
5.2 Electrical Connection .........................................................................................................................15
5.3 Troubleshooting .................................................................................................................................15
6. Functions Overview..................................................................................................................................16
6.1 Function Description ..........................................................................................................................16
6.1.1 Starting Up the Product As Supplied......................................................................................16
6.1.2 Starting Up the Product with User-Defined Settings ..............................................................16
6.2 LED Symbols .....................................................................................................................................18

3Inductive Sensors
7. Setup via IO-Link .....................................................................................................................................19
8. Maintenance Instructions ........................................................................................................................20
9. Proper Disposal ........................................................................................................................................20
10. Appendix ...................................................................................................................................................20
10.1 Revision History .................................................................................................................................20
10.2 Declarations of Conformity.................................................................................................................20

4General
1. General
1.1 Information Concerning these Instructions
• These instructions apply to products designated IRxx00x.
• These instructions make it possible to use the product safely and efficiently.
• These instructions are an integral part of the product and must be kept on hand for the entire duration of its
service life.
• Local accident prevention regulations and national work safety regulations must be complied with as well.
• The product is subject to further technical development, and thus the information contained in these oper-
ating instructions may also be subject to change. The current version can be found at www.wenglor.com in
the product’s separate download area.
NOTE!
The operating instructions must be read carefully before using the product and must be kept
on hand for later reference!
1.2 Explanations of Symbols
• Safety precautions and warnings are emphasized by means of symbols and signal words.
• Safe use of the product is only possible if these safety precautions and warnings are adhered to.
• The safety precautions and warnings are laid out in accordance with the following principle:
SIGNAL WORD
Type and source of danger!
Possible consequences in the event that the hazard is disregarded.
• Measures for averting the hazard
The meanings of the signal words, as well as the scope of the associated hazards, are listed below:
DANGER!
This signal word indicates a hazard with a high degree of risk which, if not avoided, results
in death or severe injury.
WARNING!
This signal word indicates a hazard with a medium degree of risk which, if not avoided, may
result in death or severe injury.
CAUTION!
This signal word indicates a hazard with a low degree of risk which, if not avoided, may
result in minor or moderate injury.

5Inductive Sensors
ATTENTION!
This word draws attention to a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTE!
A note draws attention to useful tips and suggestions, as well as information regarding
efficient, error-free use.
1.3 Limitation of Liability
• The product has been developed in consideration of the current state-of-the-art technology, as well as
applicable standards and guidelines. Subject to change without notice. A valid declaration of conformity can
be found at www.wenglor.com in the product’s separate download area.
• wenglor sensoric elektronische Geräte GmbH (hereinafter referred to as "wenglor") excludes all liability in
the event of:
• Non-compliance with the instructions
• Use of the product for purposes other than those intended
• Use by untrained personnel
• Use of unapproved replacement parts
• Unapproved modification of products
• These operating instructions do not include any guarantees from wenglor with regard to the described pro-
cedures or specific product characteristics.
• wenglor assumes no liability for printing errors or other inaccuracies contained in these operating instruc-
tions unless wenglor was verifiably aware of such errors at the point in time at which the operating instruc-
tions were prepared.
1.4 Copyrights
• The contents of these instructions are protected by copyright law.
• All rights are reserved by wenglor.
• Commercial reproduction or any other commercial use of the provided content and information, in particular
graphics and images, is not permitted without previous written consent from wenglor.

6For Your Safety
2. For Your Safety
2.1 Use for Intended Purpose
This wenglor product is intended for use in accordance with the following functional principle.
This sensor is used to detect metal objects.
An LC circuit is set up around the ring-shaped opening. The electromagnetic field generated by this circuit is
influenced when metal (for instance, steel, aluminum, or brass) approaches.
The target group is manufacturers of screwdriving and feeding technology.
2.2 Use for Other than the Intended Purpose
• Not a safety component in accordance with 2006/42/EC (Machinery Directive).
• The product is not suitable for use in potentially explosive atmospheres.
• The product may be used only with accessories supplied or approved by wenglor, or in combination with
approved products. A list of approved accessories and combination products can be found at
www.wenglor.com on the product detail page.
DANGER!
Risk of personal injury or property damage in case of use for other than the intended
purpose!
Use for other than the intended purpose may lead to hazardous situations.
• Observe instructions regarding use for intended purpose.
2.3 Personnel Qualifications
• Suitable technical training is a prerequisite.
• In-house electronics training is required.
• Trained personnel who use the product must have (permanent) access to the operating instruc-
tions.
DANGER!
Risk of personal injury or property damage in case of incorrect initial start-up and
maintenance!
Personal injury and damage to equipment may occur.
• Adequate training and qualification of personnel
2.4 Modification of Products
DANGER!
Risk of personal injury or property damage if the product is modied.
Personal injury and damage to equipment may occur. Noncompliance may result in loss of
the CE mark and voiding of the warranty.
• Modification of the product is not permitted

7Inductive Sensors
2.5 General Safety Precautions
NOTE!
• These instructions are an integral part of the product and must be kept on hand for the
entire duration of its service life.
• In the event of possible changes, the current version of the operating instructions can be
found at www.wenglor.com in the product’s separate download area.
• Read the operating instructions carefully before using the product.
• Protect the sensor against contamination and mechanical influences.
2.6 Approvals and Protection Class

8Technical Data
3. Technical Data
3.1 General Data
IR2D001 IR3D001
Inductive Data
Inside Diameter 10.2 mm 15.1 mm
Functional Principle Dynamic
Smallest Recognizable Object (∅) 2 mm * 2.5 mm*
Correction Factors for V2A Stainless
Steel/CuZn/Al 1/1/1
Electrical Data
Supply Voltage 10…30 V DC
Current Consumption
(Operating Voltage = 24 V) < 20 mA
Object Speed < 50 m/s
Response Time < 100 µs
Ready-State Delay 1 s
Switching Output Voltage Drop 1.5 V
Temperature Range 0...60°C
Short-Circuit Proof Yes
Reverse Polarity and Overload-Proof Yes
Switching Output Switching Current 100 mA
Interface IO-Link V1.1
Mechanical Data
Connection Type M8×1, 4-pin
Setting Method Potentiometer/IO-Link
Hanger Opening/Closing Cycles Max. 100
Degree of Protection IP 54
Adjustable Parameters
Output
PNP
Push-Pull
NPN
Circuit
NO
NC/NO
NC
Pulse Length 5…200 ms
Other Parameters Sensitivity
Alternative frequency
Output Function
PNP  
NPN  
NC  
NO  
Technical Safety Data
MTTFd (EN ISO 13849-1) 1019, 99
* Relates to a steel ball

9Inductive Sensors
3.2 Housing Dimensions
IR2x00x
IR3x00x

10 Technical Data
3.3 Connection Diagram
Applies to sensors designated IRxx001
Legend
Wire Colors according to IEC 60757
Platinum measuring resistor
not connected
Test Input
Test Input inverted
Trigger Input
Ground for the Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Ground for the Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green/Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety Output
Signal Output
Ethernet Gigabit bidirect. data line (A-D)
Encoder 0-pulse 0-0 (TTL)
Encoder A/A (TTL)
Encoder B/B (TTL)
Encoder A
Encoder B
Digital output MIN
Digital output MAX
Digital output OK
Synchronization In
Synchronization OUT
Brightness output
Maintenance
reserved
PT
PT

11Inductive Sensors
3.4 Complementary Products
wenglor can provide you with suitable connection equipment for your product.
Mounting technology: soft binder ZR0E001
Connection line: S60, S61, ZCFL
3.5 Control Panel
17 = Sensitivity adjuster
0b = Pulse length adjuster
1c = Status display/setup aid
3a = Switching status indicator/error indicator
68 = Supply voltage indicator
3.6 Scope of Delivery
• Sensor
• Soft binder

12 Transport and Storage
4. Transport and Storage
4.1 Transport
Upon receipt of shipment, the goods must be inspected for damage in transit. In the case of damage, con-
ditionally accept the package and notify the manufacturer of the damage. Then return the device, making
reference to damage in transit.
4.2 Storage
The following points must be taken into consideration with regard to storage:
• Do not store the product outdoors.
• Store the product in a dry, dust-free place.
• Protect the product against mechanical impacts.
• Protect the product against exposure to direct sunlight.
ATTENTION!
Risk of property damage in case of improper storage!
The product may be damaged.
• Storage instructions must be complied with.
5. Installation and Electrical Connection
5.1 Installation
• Protect the product from contamination during installation.
• Observe all applicable electrical and mechanical regulations, standards, and safety rules.
• Protect the product against mechanical influences.
• Make sure that the sensor is mounted in a mechanically secure fashion.
• The active surface of the sensor may not contact any other machine parts.
ATTENTION!
Risk of property damage in case of improper installation!
The product may be damaged.
• Comply with installation instructions.
CAUTION!
Risk of personal injury or property damage during installation!
Personal injury and damage to the product may occur.
• Ensure a safe installation environment.

13Inductive Sensors
5.1.1 Installation Using the Soft Binder
1 2
• Insert the soft binder on the hinge side (to prevent
it from being lost) and thread it through the feed-
through
• Open the device’s hanger
• Place the soft binder around the feed tube
3 4
• Thread the soft binder through the second feed-
through on the device
• Tighten the soft binder until the tube is inside the
device’s active surface
• Close the device’s hanger, tighten the soft binder,
and insert it into the device

14 Installation and Electrical Connection
5.1.2 Other Installation Options
As a further installation option, the sensor has two holes that can be used to install the sensor using mounting
technology. Please note that suitable mounting technology must be provided by the customer. The maximum
tightening torque when using an M4 mounting screw is 2.9 Nm. In addition, the minimum installation distance
to metal (cf. “3. Technical Data” on page 8) must be maintained.
Example illustration showing installation using a bracket
5.1.3 Installation Instructions
Adjacent devices alternating between alternative
frequency / without alternative frequency
Adjacent devices with the same frequency setting
IR2x00x IR3x00x IR2x00x IR3x00x
A 0 mm 0 mm A 0 mm 0 mm
B X0 mm 0 mm B X15 mm 30 mm
B Y0 mm 0 mm B Y35 mm 50 mm
C 5 mm 5 mm C 5 mm 5 mm

15Inductive Sensors
5.1.4 Smallest Recognizable Object
The smallest recognizable object indicates the minimum size of a steel ball that can be reliably detected by
the sensor. The correction factor 1 can be used to derive the specified resolution with other materials such as
stainless steel, brass, or aluminum.
5.2 Electrical Connection
Wire the sensor according to the connection diagram (see section 3.2).
• If using IO-Link, connect the sensor to 18...30 V DC.
• If not using IO-Link, connect the sensor to 10...30 V DC.
• Alternative frequency activated: Pin 2 to +
• Alternative frequency deactivated: Pin 2 to 0/open
DANGER!
Risk of personal injury or property damage due to electric current.
Voltage-conducting parts may cause personal injury or damage to equipment.
• The electric device may be connected by appropriately qualified personnel only.
5.3 Troubleshooting
Error Possible Cause Elimination
Error Short circuit Check the electrical wiring and eliminate the short
circuit
Mechanical damage to the coil Replace the sensor
Hanger not closed Close the hanger
Required action in case of fault:
NOTE!
• Shut down the machine.
• If the error cannot be eliminated, please contact wenglor’s support department.
• Do not operate in case of indeterminate malfunctioning.
• The machine must be shut down if the error cannot be definitively explained or properly
eliminated.
DANGER!
Risk of personal injury or property damage in case of non-compliance!
The system’s safety function is disabled. Personal injury and damage to equipment may
occur.
• Required action as specified in case of fault.

16 Functions Overview
6. Functions Overview
This section explains the sensor’s functions and LED symbols in more detail.
6.1 Function Description
This function description refers to a setting on the potentiometer of the sensor.
6.1.1 Starting Up the Product As Supplied
• Device is ready for use and can be put into operation
The sensitivity is at the maximum setting in order to be able to detect the smallest possible objects. The time
delay setting is set to 200 ms (turn all the way to the right).
6.1.2 Starting Up the Product with User-Defined Settings
When adjusting settings on the device, a distinction can be made between setting the sensitivity and the time
delay.
Set the sensitivity to object size:
1. Turn the potentiometer all the way to the left
SENS
TIME
LED symbols as per
“6.2 LED Symbols” on page 18
2. Guide the object to be detected through the ring (active surface)
of the sensor
3. If the setup aid is off or flashing, turn the potentiometer clock-
wise in the direction of (+) until the setup aid illuminates
continuously SENS
TIME

17Inductive Sensors
Set the pulse length:
The pulse length adjuster can be used to set the time until the signal drops at the output between 5 ms and
200 ms.
The following applies to sensors based on the dynamic principle:
Target
tt
tdtp
Output
The following applies to sensors based on the static principle:
For sensors based on the static principle, the time in which the object is in the device’s active surface can be
longer than the set pulse length (tt ≥ td), since the output remains switched as long as an object is in the active
surface.
Activating Alternative Frequency
The alternative frequency can be set either via the cable connection (see “5.2 Electrical Connection” on page
15) or via IO-Link.
The activated working frequency enables another sensor for which this setting is deactivated to be operated in
the immediate vicinity without the sensors interfering with each other.
tt = Time target
td = Time delay
tp = Time pause 5 ms
tt < td

18 Functions Overview
6.2 LED Symbols
Setup display Switching status indicator/supply
voltage indicator
Cause
Green* Blue No object present yet
Green** Blue Object was not reliably detected
Green Blue Object was reliably detected
Green Blue Object was not detected
 Red Hanger not closed
Red
The device has an error.
Information on how to remedy the error can be
found in the troubleshooting section; see “5.3
Troubleshooting” on page 15.
Green Yellow Switching output active
–Blue ** Device has been set to factory settings/alternative
frequency has been activated
Not illuminated Flashing Continuously illuminated
* Flashing behavior: 1 Hz 50 ms ON to 950 ms OFF
** Flashing behavior: 1 Hz 500 ms ON to 500 ms OFF

19Inductive Sensors
7. Setup via IO-Link
Process and parameter data can be found in the interface protocol at: www.wenglor.com Product World 
Enter the desired product number as a search term Under “Downloads” on the product page.
Process Data:
• Counter
• Object size
• Object width (how long the object was detected)
• Error indicator
• Warning
• Switching status A1
• Switching status A2
Parameter data:
• Potentiometer lock
• Parametrization of sensitivity
• Parametrization of pulse length
• Output function A1
• Output function A2
• Alternative frequency

20 Maintenance Instructions
8. Maintenance Instructions
NOTE!
• This wenglor sensor is maintenance-free.
• Cleaning and inspection of the plug connections at regular intervals are advisable.
• Do not clean the sensor with solvents or cleaning agents that could damage the product.
• The product must be protected against contamination during initial start-up.
9. Proper Disposal
wenglor sensoric GmbH does not accept the return of unusable or irreparable products. Respectively valid
national waste disposal regulations apply to product disposal.
10. Appendix
10.1 Revision History
Version Date Description/Changes
1.0.0 7/04/2023 Initial version of the operating instructions
10.2 Declarations of Conformity
Declarations of conformity can be found on our website at www.wenglor.com in the product’s separate down-
load area.