Westin 58-41075 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N. 75-5841075-RevA ECO #: W18-0236 DATE: 02/27/19
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1 2 SIDE POD ASSEMBLY (1 DRIVER, 1 PASSENGER) 10MM SOCKET
2 2 MESH SIDE COVERS (1 DRIVER, 1 PASSENGER) 10MM WRENCH
3 1 CENTER SECTION 13MM SOCKET
4 1 LED LIGHT BRACKET 13MM WRENCH
5 1 DRIVER MOUNTING BRACKET 16MM SOCKET
6 1 PASSENGER MOUNTING BRACKET 16MM WRENCH
7 1 PASSENGER SUPPORT BRACKET 18MM SOCKET
8 1 DRIVER SUPPORT BRACKET 19MM WRENCH
9 6 HOLE PLUG RATCHET
10 6 SENSOR TAB TORQUE WRENCH
11 10 M12 HEX HEAD BOLT (YELLOW ZINC)
12 10 M12 HEX NUT (YELLOW ZINC)
13 20 M12 FLAT WASHER (YELLOW ZINC)
14 10 M12 SPLIT LOCK WASHER (YELLOW ZINC)
15 6 M6 CARRIAGE BOLT (YELLOW ZINC)
16 6 M6 SPLIT LOCK WASHER (YELLOW ZINC)
17 6 M6 HEX NUT (YELLOW ZINC)
18 12 M6 FLAT WASHERS (YELLOW ZINC)
19 6 M10 SPLIT LOCK WASHER (BLACK ZINC)
20 12 M10 FLAT WASHER (BLACK ZINC)
21 6 M10 HEX HEAD BOLT (BLACK ZINC)
22 6 M10 HEX NUT (BLACK ZINC)
23 12 M6 FLAT WASHER (BLACK ZINC)
24 12 M6 SPLIT LOCK WASHER (BLACK ZINC)
25 4 M6 BUTTON HEAD BOLT (BLACK ZINC)
26 12 M6 SERRATED FLANGE NUT (BLACK ZINC)
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
PRO-MOD BUMPER
APPLICATION:
2019 Ram 1500 (Excl. 2019 Ram 1500 Classic; Rebel)
PART NUMBER:
58-41075

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N. 75-5841075-RevA ECO #: W18-0236 DATE: 02/27/19
ITEM 1 (Driver)
ITEM 4 ITEM 5 ITEM 6
ITEM 7
ITEM 8 ITEM 9 ITEM 10
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
ITEM 1 (Passenger) ITEM 2 (Driver)
ITEM 2 (Passenger) ITEM 3
2. Unplug any connections to the OEM front bumper (sensors, fog lights ,etc).
3. Remove the front inner fender pieces by removing the 5 screws shown in Figure 1.
4. Remove the three frame mounted bolts from each side of the vehicle. Then, carefully remove the OEM bumper. See
Figure 2.

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N. 75-5841075-RevA ECO #: W18-0236 DATE: 02/27/19
5. Unplug and remove the active valence from the vehicle if equipped. See Figure 3.
Fig 1 Fig 2
Fig 3
Driver Side Shown Driver Side Shown
6. Use the supplied M10 Hardware to attach each Side Pod Assembly (1,2) to the Center Section (3). See Figure 4.
7. Tighten side pods in position now. Torque M10 hardware to 38 ft-lbs.
8. Use the supplied M6 Hardware to attach the LED Brackets (4) to the center section. See Figure 5. Note: If installing an
LED Light Bar (sold separately), install it at this time.
Fig. 4
Driver Side Shown
Fig. 5
Driver Side Shown
4
3
25
24
23
26
22 19
20
21

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N. 75-5841075-RevA ECO #: W18-0236 DATE: 02/27/19
8. Loosely install the bumper assembly to the Mounting Brackets (5,6) using the supplied M12 Hardware. See Figures 6 & 7.
Fig. 10
Fig. 6 Fig. 7
Driver Side Shown Driver Side Shown
9. Remove the parking sensors from the OEM bumper. Pay attention to the orientation of the sensors. They must be installed
in the same orientation. Handle sensors with care, they are very delicate .
10. Use the Sensor Tab (10) along with the supplied M6 Hardware (15-18) to install the sensors as shown in Figure 8.
11. Carefully route the harness around the bumper.
Note: Zip ties or double sided tape can e used to route harness and to hold the sensor in position.
PARKING SENSOR INSTALLATION
*If not installing sensors, install Hole Plugs (9) into holes on bumper and proceed.
Factory Sensor
Item 10
Items 15-18

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N. 75-5841075-RevA ECO #: W18-0236 DATE: 02/27/19
11. Loosely attach the preassembled bumper to the vehicle frame using the supplied M12 Hardware. See Figure 9.
12. Loosely attach the Support Brackets (7,8) to the rear of the mounting location for the bumper. See Figure 10 and 11.
Attach to these locations using items
11-14.
Fig. 9 Fig. 10
Item 8
Driver Side Shown
Items 19-22
Fig. 11