Westin 58-53935 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5853935-RevA ECO #: W18-0191 DATE: 03/26/19
INSTALLATION INSTRUCTIONS
OUTLAW NERF STEP BARS
APPLICATION:
2015-2019 Ford F-150 SuperCab; 2017-2019 Ford F-250/350
SuperCab
PART NUMBER:
58-53935
ITEM 1 ITEM 3 ITEM 4
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
11DRIVER SIDE STEP BAR 13MM SOCKET
21PASSENGER SIDE STEP BAR 13MM WRENCH
32MOUNTING BRACKET A 16MM SOCKET
42MOUNTING BRACKET B 16MM WRENCH
54MOUNTING BRACKET C RATCHET
616 M8 SPLIT LOCK WASHER TORQUE WRENCH
716 M8 FLAT WASHER
816 M8 HEX NUT
94M8 SQUARE NECK BOLT
10 8M10 HEX HEAD CAP SCREW
11 8M10 BELLVILLE WASHER
12 8M10 SERRATED FLANGE NUT
13 12 M8 PLASTIC RETAINER SQUARES
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
ITEM 5
Passenger Side Opposite

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5853935-RevA ECO #: W18-0191 DATE: 03/26/19
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
2. Start installation on driver’s side. On the rocker panel find locations of factory studs. In each location there should be 3
studs. See Figure 1.
3. Insert (1) M8 Plastic Retainer (Item 13) on each factory stud. See Figure 2.
4. Insert the M8 round head square neck bolt (Item 9) through the Mounting Bracket C (Item 5) square hole. Then insert the
M8 round head square neck bolt through mounting brackets (Item 3-5) bottom circular hole. Loosely secure with (1) M8
hex nut, (1) M8 split lock washer, and (1) M8 flat washer. See Figure 3.
5. Align sub-assembly with the 3 factory studs. Lower 2 factory studs will align with Mounting Bracket C and top factory
stud will align with mounting brackets. Loosely secure sub-assembly with (3) M8 hex nut, (3) M8 split lock washer, and
(3) M8 flat washer. See Figure 4. (Note: See page 3 for bracket orientation)
6. Repeat Step 3-4 for every mounting location.
Figure 1
Factory studs shown
Front Driver side shown Figure 2
12
Figure 3
Front Driver
Side Mounting
Location Shown Figure 4
13
953
768
8
6
7

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5853935-RevA ECO #: W18-0191 DATE: 03/26/19
7. For step bar installation, use the supplied M10 Hardware to loosely secure the step bar to the preinstalled brackets. See
Figures 5 & 6. Note: Mounting Bracket A is shown; bar installs to other brackets similarly.
8. Align and adjust the step bars and brackets as needed, then fully tighten all hardware: M8 to 18 ft-lbs, M10 to 38 ft-lbs.
Figure 5 Figure 6
Driver Side Rocker Panel
Passenger Side Rocker Panel
Front
Front
ITEM 3 ITEM 4
ROCKER PANEL BRACKET LOCATIONS
ITEM 3ITEM 4

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5853935-RevA ECO #: W18-0191 DATE: 03/26/19
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER
INSTALLATION COMPLETE
F-250 SuperCrew Shown

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5853935-RevA ECO #: W18-0191 DATE: 03/26/19
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer, birth defects or
other reproductive harm. For more info go to www.p65warnings.ca.gov