Westin 65-1305 User manual

1
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-3069 REV A ECO #: W14-0042 DATE: 7/20/2015
1. Remove contents from box, verify if all parts listed are present and free from damage. Carefully read and understand all instruc-
tions before attempting installation. Failure to identify damage before installation could lead to a rejection of any claim.
2. Start installation in the rear of the vehicle. Locate holes under the vehicle in where the M12 and M10 hardware will be mounted.
See Figure 1 & 2.
3. Adjust and align center holes of the receiver hitch assembly as necessary. Loosely secure the receiver hitch assembly to the vehi-
cle. On the passenger side, mark location to drill a 1/2” hole. See Figure 2.
4. Remove the receiver hitch assembly from vehicle. On the passenger side drill the 1/2” hole. Clean metal debris from hole.
5. Insert both M10 bolt plates into place. On the driver side, the bolt plate will be placed in the already existing hole. On the pas-
senger side, the bolt plate will be placed in the recently drilled hole. See Figure 1 & 2.
CLASS 3 RECEIVER HITCH
APPLICATION: ODYSSEY 1999-2015
APP PART # 65-1305
INSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC.
NOTICE: This product complies with all safety specifications and requirements defined for V.E.S.C. regulation V-5 & SAE J684
WARNING: Never exceed the capacity ratings shown on the receiver hitch or the tow vehicle. See your vehicle’s
owners guide for towing guidelines.
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
11RECEIVER HITCH ASSEMBLY 19MM SOCKET
24M12 HEX CAP SCREW 10MM SOCKET
34M12 FLAT WASHER DRILL
44M12 SPLIT LOCK WASHER TORQUE WRENCH
52M10 LONG BOLT PLATE
62M10 HEX NUT
72M10 FLAT WASHER
82 M10 SPLIT LOCK WASHER
Hitch Assembly

2
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-3069 REV A ECO #: W14-0042 DATE: 7/20/2015
INSTALLATION COMPLETE
Location where to drill
Passenger side shown
Drill 1/2” hole
Figure 2
Location of where to screw
Driver side shown
M12
M10
Figure 1
Insert M10 bolt plate
CARE INSTRUCTIONS
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER
6. With assistance, align and adjust the receiver hitch assembly as necessary with the intended holes. See Figure 1 & 2. Loosely
secure the receiver hitch assembly to the frame using the supplied M10 and M12 hardware. Refer to Hitch Assembly on page 1
for correct placement.
7. Align and adjust the receiver hitch assembly as necessary. Tighten and torque all M10 hardware to 55-60 ft-lbs and M12 hard-
ware to 65-70 ft-lbs.

3
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-3069 REV A ECO #: W14-0042 DATE: 7/20/2015
AUTOMOTIVE PRODUCTS, INC.
San Dimas, California
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RE-
SULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product. Us-
er should never exceed the vehicle manufacturers maximum tow and weight rating regardless of
the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS
VEHICLE DAMAGE.
WARNING
WARNINGS & NOTICES
FOR THE INSTALLATION OF
WESTIN TOWING PRODUCTS - CLASS III RECEIVER HITCH
NOTICE
Westin Receiver Hitches are designed to accommodate a 2”- square receiver draw bar rated for
class III/IV towing. Closely follow all Westin Installation Instructions for the proper installation of
product. Improper installation can result in death, serious injury, and/or product and vehicle dam-
age. In the operation of these products, it is imperative to observe precautions for your personal
safety and the safety of others.