Westin 35-1380 User manual

S1.
S2.
S3.
tep
tep
tep
Step 4.
Step 5
R
T
emovethecontentsfromtheboxandcheckforanydamage.Verifyallpartsagainstthepartslist.
Readandunderstandinstructionscompletelybeforebeginninginstallation.
oassemblethegrilleguard,positionthecentersection,SeeFigure1forproperorientation.Thebottomside
ofthe centersectionisthelonger end. Insertwings sothatwing slotsline upwithcenter sectionholes. Attach
uprightsto grilleguard centerassembly using½” hexhead bolts,flatwashers,andlockwashers.
PlaceProtectiveRubberStripsonuprightswherecontacttovehicleoccurs.
When Grille Guard is positioned against vehicle, the outer wing profiles should match the vehicle head-
lamp/turnlampassembly. Ifnot,reversewingsincentersectionsidetoside.
At tow hook, loosen rear bolt and remove front bolt. Install the bottom bracket between the frame and tow
hook with the thick end of bracket toward center of vehicle. Re-insert bolt (leave loose). Repeat step on
oppositeside.
From inside of frame behind bumper, position bracket so that front of bracket protrudes between top of
bumper and bottom of grille. (If necessary, push down on bumper cover plastic to slide bracket through.)
Locate bumper bolt ends (front side of frame), then position bracket slots on bolt ends, over existing nuts.
Handtighten.
Note:
.
75-0224 PAGE 1 OF 2
REVISION A 7/13/99
PARTS KIT CONTENTS TOOLS REQUIRED
QTY DESCRIPTION
1 UPRIGHT - PASSENGER SIDE 3/4” SOCKET
1 UPRIGHT - DRIVER SIDE 15MM SOCKET
1 WING - PASSENGER SIDE 19MM SOCKET
1 WING - DRIVER SIDE
1 CENTER SECTION
1 TOP BRACKET - PASSENGER
1 TOP BRACKET - DRIVER
2 BOTTOM BRACKET
4 PROTECTIVE RUBBER STRIP
8 1/2-13 X 1.25” HEX HEAD BOLTS
6 1/2” SAE FLAT WASHERS
8 1/2” SPLIT LOCK WASHERS
4 12MM JAM NUTS
RATCHET
TORQUE WRENCH
3/4” WRENCH
SOCKET EXTENSION
INSTALLATION INSTRUCTIONS
APPLICATION: 1999 FORD F-SERIES LIGHT DUTY AND
EXPEDITION
(4X4 WITH TOW HOOKS ONLY)
CLASSIC
GRILLE GUARD
ASSEMBLY
35-1370
35-1380

Handtightensupplied12mmjamnutsoverbracket. Repeatsteponoppositeside.
Step 6.
Step 7.
Take assembled Grille Guard and place against vehicle, align all brackets with threaded inserts on uprights.
Boltuplooselyusingremaining½”hardware.(Usenoflatwashersontopbrackets).
Adjust Grille Guard so centered and level and torque all hardware to: ½” fasteners to 65 ft. lbs; 12mm nuts to
60ft.Lbs;towhookbolts 75ft.lbs.
Westin Automotive Products, Inc.
5200 N. Irwindale Ave. Suite 220
Irwindale, Ca. 91706
Thank You for choosing Westin products
For additional installation assistance please call
Customer service [phone] or [phone]
75-0224 PAGE 2 OF 2
REVISION A 7/13/99
Finish protection - Westin products have a high quality finish that must be cared for like any
other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax
(purecarnauba,forexample)onaregularbasis. Theuseofcleanerwaxoranycompoundwhich
contains an abrasive is detrimental, as the compounds scratch the finish and open it to corro-
sion.
LIGHT MOUNT
BOTTOM TUBE
5/16 NYLON FLAT WASHER
5/16-18 X 1”
SELF-THREADING SCREW
LIGHT MOUNT ATTACHMENT FIGURE
LIGHTED MODELS ONLY
CENTER SECTION OF GRILLE GUARD
FRONT SIDE
FIGURE 1
FOR PROPER ORIENTATION DURING ASSEMBLY,
SPOT WELD ON UPRIGHT BAR SHOULD BE UP
SPOT WELD
DRIVER SIDE INSTALLATION SHOWN - PASSENGER SIDE OPPOSITEDRIVER SIDE INSTALLATION SHOWN - PASSENGER SIDE OPPOSITE
BOTTOM BRACKET
(WIDE END TOWARD
CENTER OF VEHICLE)
VEHICLE
FRAME
12MM JAM NUTS
TOP BRACKET
1/2-13 X 1.25” HEX BOLT
1/2” FLAT WASHER
1/2” LOCK WASHER
TOW HOOK