Westin Pro-Traxx 5 WTW User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-1132-RevB ECO #: W17-0019 DATE: 3/20/17
INSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS,
Pro-Traxx 5 WTW
APPLICATION:
2007-2017 Toyota Tundra D-Cab 6.5 ft. Bed
PART NUMBER:
21-534170, 21-534175
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1,2 2 STEP BAR ASSEMBLY, DRIVER (1) AND PASSENGER (2) 13MM SOCKET
3 2 FRONT MOUNTING BRACKET HEX KEY
4 2 MIDDLE MOUNTING BRACKET RATCHET
5 2 REAR MOUNTING BRACKET TORQUE WRENCH
6 12 M8 HEX HEAD CAP SCREW (YELLOW ZINC)
7 12 M8 FLAT WASHER (YELLOW ZINC)
8 12 M8 SPRING LOCK WASHER (YELLOW ZINC)
9 12 M10 HEX BUTTON HEAD SOCKET CAP SCREW (BLACK ZINC)
10 12 M10 FLAT WASHER (BLACK ZINC)
11 12 M10 INTERNAL TOOTHED LOCK WASHER (BLACK ZINC)
12 6 PLASTIC BRACKET COVER
13 12 M6 HEX HEAD CAP SCREW (YELLOW ZINC)
14 24 M6 FLAT WASHER (YELLOW ZINC)
15 12 M6 NYLOCK NUT (YELLOW ZINC)
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
2. Start installation on the driver’s side. On the rocker panel, find locations of factory bolts. Remove factory hardware and
discard. Note: Brackets will be installed in these locations with provided hardware. See Figures 1 & 2.
3. Locate Front, Middle, and Rear Mounting Brackets (Items 3, 4, 5). Using the supplied M8 hardware, loosely install the
brackets to the rocker panel. See Figures 3, 4, & 5. Note: Item 5 has a notch to differentiate from Item 4. See image
ITEM 4 ITEM 12ITEM 3 ITEM 5

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-1132-RevB ECO #: W17-0019 DATE: 3/20/17
Figure 1
Location for Item 3
Remove factory bolts
Driver side shown
Remove 4 factory bolts
Driver side shown
Location for Item 4 & 5
Remove Bolts
Figure 2
Item 3 installed
Driver side shown Figure 3
Item 4 installed
Driver side shown Figure 4
M8 Hardware Assembly
Driver side shown
Front
Figure 5
4. Locate (1) plastic bracket cover (Item 12) and loosely secure it to the (6) brackets using the provided hardware: (2) M6 hex
head cap screws, (4) M6 flat washers, and (2) M6 nylon nuts. Repeat for every bracket. See Figure 6.
5. Locate the Driver Step Bar Assembly (Item 1) and align it with the brackets. See Figure 7.
6. Loosely install the Driver Step Bar Assembly using supplied M10 hardware. See Figure 8.

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-1132-RevB ECO #: W17-0019 DATE: 3/20/17
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
7. Align and adjust the step bar and brackets as necessary then tighten and torque all fasteners as follows: M8 to 20 ft-lbs,
M10 30 ft-lbs, and M6 to 5-7 ft-lbs.
8. Repeat for the passenger side.
TOYOTA TUNDRA D-CAB SHOWN
INSTALLATION COMPLETE
Figure 6
Front
Figure 7
Align Bracket slots with Step Bar holes
Driver side shown
Figure 8

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-1132-RevB ECO #: W17-0019 DATE: 3/20/17
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS
VEHICLE DAMAGE.
WARNING
AUTOMOTIVE PRODUCTS, INC.