Westin WJ2 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1 1 FRONT BUMPER ASSEMBLY 7MM SOCKET
2 2 LED MOUNTING BRACKET *59-80125 only 7MM WRENCH
3 8 M10 FLAT WASHER 10MM SOCKET
4 8 M10 SPLIT LOCK WASHER 10MM WRENCH
5 4 M10 HEX HEAD CAP SCREW 13MM SOCKET
6 4 M10 HEX NUT 13MM WRENCH
7 4 M6 SERRATED FLANGE NUT 16MM SOCKET
8 4 M6 HEX SOCKET BUTTON HEAD BOLT 16MM WRENCH
9 4 M6 NYLOCK NUT ALLEN WRENCH
10 4 SMALL M6 FLAT WASHER RATCHET
11 4 M4 HEX NUT TORQUE WRENCH
12 20 M4 FLAT WASHER
13 4 M4 SPLIT LOCK WASHER
14 4 SHORT M4 HEX SOCKET BUTTON HEAD SCREW
15 6 LONG M4 HEX SOCKET BUTTON HEAD SCREW
16 6 M4 HEX SOCKET CAP SCREW
17 12 M4 NYLOCK NUT
18 1 RUBBER GROMMET
19 6 NYLON SPACER
20 8 LARGE M4 FLAT WASHER
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
WJ2 FULL-WIDTH FRONT BUMPER
APPLICATION:
2018 Jeep Wrangler JL
PART NUMBER:
59-80105, 59-80115, 59-80125
ITEM 1 (LED) ITEM 2

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
2. Unplug any wire connections to the bumper such as fog lights.
3. Loosen the bolts securing the reinforcement brackets to the frame. See Figure 1.
Fig 1
4. Remove the 4 nuts on each frame horn that secure the bumper to the vehicle. See Figures 2 & 3.
5. Carefully remove the front bumper from the vehicle
Fig 3
Fig 2

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
6. Align the Front Bumper Assembly (1) with the holes on the frame.
7. Use the supplied M10 Hardware (3-6) to secure the bumper to the vehicle. See Figures 4 & 5.
Fig 4
Fig 5
FOG LIGHT INSTALLATION (Full-width Bumper only)
Factory Fog Lights: OEM Steel Bumpers: Use the supplied M6 Flat Washer (10) and Nylock Nut (9) along with the factory hardware, se-
cure the fog light to the bracket as shown in Figure 1.
OEM Plastic Bumpers: Use the supplied M4 hardware to secure the bracket to the bumper. See Figure 2. See Page 4 for Rubicon Plastic
Bumper applications. Note: Light not shown.
Aftermarket Lights: Use the universal mounting tab as shown in Figure 3. Note: Lights sold separately.
Fig 3 Aftermarket
Light Mount
Fig 1
Fig 2

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
FOG LIGHT INSTALL CONT.
*Rubicon Models w/ Plastic Bumpers*: If the vehicle is a Rubicon model with the OEM Plastic Bumper, you will need to use 3 Nylon
Spacers (19) and the supplied M4 Hardware to secure the light into place. See Figure 4.
Factory Fog Light will
insert between the Flat
Washer and Nylon Spacer.
Fig 4
20

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
20 Inch LED Light Bar Installation (59-80125 Only)
1. Loosely install the LED mounting tabs (2) to the front bumper assembly (1) using the supplied M6 hardware (7 & 8). See
Figure 1. Note: The mounting tabs can be installed at a range of distances from one another in order to accommodate the
width of the light bar. Figure 2 shows the mounting tabs arranged in a wide configuration while Figure 3 shows them ar-
ranged in a narrow configuration.
2. Install light bar according to manufacturer’s instructions.
3. Tighten M6 hardware to 5-7 ft-lbs.
Fig. 1
Fig. 2
Fig. 3
Passenger Side
LED Light Mounting Instructions
Lights Sold Separately
Fig. 4
Rock Light Installation
Install lights in the lower corners of the bumper using sup-
plied M4 hardware (11-14). See Figure 4.
Note: Wire lights per manufacturer’s instructions.
Driver’s Side
11
13
12
14
8
7

6
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER
Installation Complete (Lights, Winch, and Skidplate Sold Separately)

7
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-598011-RevB ECO #: W18-0118 DATE: 08/17/18
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer, birth defects or
other reproductive harm. For more info go to www.p65warnings.ca.gov