1 2 STEP BAR (PURCHASED SEPARATELY)
2 4 BRACKET
3 4 M8-1.25 X 25MM HEX HEAD BOLT
4 4 5/16” FLAT WASHER
5 4 5/16” LOCK WASHER
6 4 M8-1.25 FLANGE NUT
7 4 M6 BOLT PLATES (INCLUDED WITH STEP TUBES )
8 16 M6 FLAT WASHERS (INCLUDED WITH STEP TUBES)
9 16 M6 LOCK NUTS (INCLUDED WITH STEP TUBES)
QTY CONTENTS - CONTENIDO - CONTENU TOOLS - HERRAMIENTA
- OUTILS
7/16” SOCKET
10MM SOCKET
13MM SOCKET
RATCHET
TORQUE WRENCH
ITEM
AUTOMOTIVE PRODUCTS, INC.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
1 2 ESTRIBOS, (SE COMPRA SEPARADO)
2 4 PIEZAS DE SUJECIÓNS
3 4 PERNOS CON CABEZA HEXAGONAL M8-1.25 X 25MM
4 4 ARANDELAS PLANAS DE 5/16”
5 4 ARANDELAS DE PRESIÓN DE 5/16”
6 4 TUERCA A PRESIÓN CON BRIDA DE M8-1.25
7 4 TORNILLO M6 PLACAS (INCLUIDO CON TUBOS STEP)
8 16 M6 ARANDELAS PLANAS (INCLUIDO CON TUBOS DE PASO)
9 16 LAS TUERCAS M6 (INCLUIDO CON TUBOS DE PASO)
1 2 MARCHE-PIEDS, (ACHETE SEPAREMENT)
2 4 SUPPORTS
3 4 BOULONS A TETE HEXAGONALE M8-1.25 X 25MM
4 4 RONDELLES PLATES 5/16 PO
5 4 RONDELLES A FREIN 5/16 PO
6 4 ECROU FREINE A EMBASE DE M8-1.25
7 4 BOULON M6 PLAQUES (INCLUS AVEC TUBES STEP)
8 16 M6 RONDELLES PLATES (INCLUS AVEC TUBES STEP)
9 16 NUTS M6 LOCK (INCLUS AVEC TUBES STEP)
DADO DE 7/16”
DADO DE 10MM
DADO DE 13MM
MANERAL
LLAVE DE TORQUE
DOUILLE 7/16 PO
DOUILLE 10MM
DOUILLE 13MM
CLIQUET
CLEF DE COUPLE
APPLICATION: 2004-11 NISSAN ARMADA; 2004-11 NISSAN TITAN
APPLICATION: 2004-11 NISSAN ARMADA; 2004-11 NISSAN TITAN
APLICACIÓN: , NISSAN ARMADA MOD. 2004-11; NISSAN TITAN, MOD. 2004-11
12
MOUNT KIT
EQUIPO DE MONTAJE
TROUSSE DE MONTAGE
22-1415
22-0020 22-0030 22-0025 22-
0035, 22-6020, 22-6025, 22-6030,
22-6035
75-0666 REVISION B 4/15/11
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning.
STEP 2. Install brackets as shown. SEE FIGURES 1 AND 2.
STEP 3. Attach step bars to the mounting brackets using the M6 hardware included with the step bars. SEE FIGURES 3,4, AND
5
STEP 4.
STEP 5. Repeat for passenger side.
Make sure step bar and brackets are properly aligned with vehicle and tighten fasteners. Recommended torque
values are 16 FT.LBS. for 8mm fasteners and 7 FT. LBS for M6 fasteners.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax,
(e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it
PASO 1. Retire el contenido de la caja y verifique que ninguna pieza se haya dañado. Verifique que no falte ninguna
pieza. Lea las instrucciones completamente antes de comenzar.
PASO 2. VEA LAS FIGURAS 1 Y 2.
PASO 3. ADJUNTAR BARRAS DE PASO PARA LOS SOPORTES DE MONTAJE UTILIZANDO EL HARDWARE M6
Instale los soportes como se muestra. Apriete con la mano.
