Whittier Wood Products Shaker 1400AFVCL User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213Outside U.S. or Canada: 541- 687- 0213
800-653-3336800-653-3336
Fax: [phone] • Fax: [phone] • wwwwww.whittie.whittierrwood.comwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.AMail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use only.
recommended for commercial use.
Congratulations!
Production Code:
Shaker
Twin Storage Bed
1400AFVCL
Candelite Finish
V N
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a handsome
addition to your home. For the best results, start
by reading the Assembly Instructions before you begin
your project.
Rev. 07/08
Assembly Instructions
Store the item: 1) in the box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may be
affecting the stability of your furniture. Tighten or repair
as needed.
This Assembly requires two people.
Unload items from this unit prior to moving.
Before
Do not overload drawers in this unit.
Do not stand or climb on this piece of furniture.
loading or moving this unit, check all screws
and supports for tightness.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.

1400AFVCL Shaker Twin Storage Bed — Parts List
1402AFVCL (x1)
If you need to replace a part, please refer to the following name/number.
Before beginning assembly, check that the quantities of parts received match this list.
Page 2 — 1400AFVCL — Rev. 07/08
1401AFVCL (x1)
F — 1/4" x 3⅜" Hex Bolt
— Qty. 6
T — 1/4" x 2½" Hex Bolt
— Qty. 6
E — #8 x 1¼" Black Screw
— Qty. 20
H — Washer — Qty.20
N — #8 x 1½" Machine Screw
— Qty. 6 O — Knob — Qty. 6
I — Pedestal Kit — Qty. 1
A — Headboard — Qty. 1
D — Insert Nuts — Qty. 12
(pre-inserted)
B — Footboard — Qty. 1
S — Side Panel — Qty. 1
C — Trestle — Qty. 4
R — Left/Right Deckboard
— Qty. 1
J — Drawer Box
— Qty. 6
P — Center Deckboard — Qty. 1
L — Drawer Face
— Qty. 6
G — 1/4" x 1¾" Hex Bolt
— Qty.8
Q — Drawer Slides — Qty. 6
(pre-installed sets)

Page 3 — 1400AFVCL — Rev. 07/08
1400AFVCL Shaker Twin Storage Bed
Assembly Instructions
TOOLS REQUIRED:
This Assembly Requires Two People
Phillips screwdriver and 7/16" wrench
* BEFORE ASSEMBLING YOUR BED, decide if you want the drawers on the
left or right side when you face the headboard. (This instruction shows the drawers
on the left.) To build the bed with drawers on the right, reverse the positions
of the headboard and footboard in Steps 4 and 5.
Remove the Trestles (C) from the back of the Headboard (A). Remove the
Drawers from the Pedestal Kit (I). Note where each drawer comes from
for easy re-installation. (Positions are also marked on the drawer backs.)
1.
C
Shipping Straps
A

Page 4 — 1400AFVCL — Rev. 07/08
H x 4
G x 4
S
C
C
C
C
H x 4
G x 4
Attach the Trestle (C) to the Pedestal (I) by using four ¼" x 1¾" Hex Bolts (G)
and Washers (H). Be sure to use the end of the Trestle (C) that has two holes.
To attach the two outside trestles, use the hole shown in Figure 2a.
To attach the two middle trestles, use the hole shown in Figure 2b.
2.
Attach the Side Panel (S) to the Trestles (C) using ¼" x 1¾" Hex Bolt (G)
and Washer (H). See Figure 3.
3.
Fig. 2
Fig. 2a Fig. 2b
Fig. 3
H
G
H
G
C
C
I

Page 5 — 1400AFVCL — Rev. 07/08
F/H
T/H
H x 6
F x 3
T x 3
A
H x 6
F x 3
T x 3
F/H
B
T/H
Attach the Footboard (B) to the Pedestal (I) with ¼" x 3-3/8" Hex Bolts (F)
and Washers (H); and to the Side Panel (S) with ¼" x 2½" Hex Bolts (T) and
Washers (H) as shown in Figure 4.
4.
Attach the Headboard (A) to the Pedestal (I) with ¼" x 3-3/8" Hex Bolts
(F) and Washers (H); and to the Side Panel (S) with ¼" x 2½" Hex Bolts
(T) and Washers (H). See Figure 5.
5.
Fig. 4
I
S
I
S
Fig. 5
H
T
HF

E x 8
Page 6 — 1400AFVCL — Rev. 07/08
E
R
Position Left/Right Deckboard (R) as shown in Figure 6 and Center
Deckboard (P) as shown in Figure 6a. There should be a small gap between
each deckboard and between the Left/Right Deckboard and the side panel.
Fasten deckboards in place with #8 x 1¼" Black Screws (E).
6.
Fig. 6
E x 12
E
P
Fig. 6a
Carefully align drawer slides into the cabinet and gently push the drawers
back into their original positions. Sleep well, and enjoy!
7.