Whittier Wood 5200AFGMS User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/14
Model #
5200AFGMS
Ambierle Sofa
Table
Glazed Millstone finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, read the
Assembly Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers or shelf.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

5200AFGMS Ambierle Sofa Table
Parts List
5200AFGMS —Page 2 —03/14
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Case Assembly
1
B
Leg
4
C
Shelf Assembly
1
D
Drawer Box (inserted)
2
E
Drawer Face (installed)
2
F
Drawer Slide (pre-installed sets)
2
G
#6 x 3/4" Philtruss Screw (inserted)
12
H
#6 x 1/2" Philtruss Screw (inserted)
12
I
#8 x 1-3/8" Lo-Profile Screw (inserted)
18
J
#8 x 1-1/4" Pan Head Screw
48
(44 inserted)
K
#8 x 7/8" Black Lo-Profile Screw (inserted)
8
L
#8 x 2" Black Screw (inserted)
1
M
3/8" x 1" Insert Nut (inserted)
8
N
1/4" x 20mm Insert Nut (inserted)
4
O
Adjustable Glide (installed)
4
P
Knob (attached)
2
Q
#8 x 1-1/4" Machine Screw (installed)
2
R
5/16" Flat Washer
8
S
3/8" x 2-1/2" Hex Bolt
8

5200AFGMS Ambierle Sofa Table
Assembly Instructions
5200AFGMS —Page 3 —03/14
Tools Required: Phillips Screwdriver, 9/16" or Adjustable Wrench, Rubber Mallet or Padded
Hammer
1. Remove the Drawer (D) from the Case Assembly (A). To remove the drawer, pull up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever. See
Figure 1a. Note where each drawer came from to ensure correct installation.
2. Turn the Case Assembly (A) upside-down on a clean, protected surface. Place two Legs (B) at
the back of the Case Assembly (A), making sure the drilled corners of the legs face toward the
Corner Blocks. Attach with 5/16" Flat Washers (R) and 3/8" x 2-1/2" Hex Bolts (S). See Figures
2 and 2a.
Fig. 2
B
B
Fig. 2a
A
R
S
x 4
x 4
S
R
Fig. 1
Drawer Release Lever
Fig. 1a

5200AFGMS Ambierle Sofa Table
Assembly Instructions
5200AFGMS —Page 4 —03/14
3. Rotate the Case and Leg assembly so that is sets on the back legs. Turn the Shelf Assembly
(C) bottom side down and place the back corners into the notches in the Back Legs. See Figure
3.
4. Place a Leg (B) at each front corner making sure that the drilled corners of the legs face toward
the Corner Blocks and the notches fit over the front corners of the Shelf. See Figures 4 and 4a.
B
Fig. 4
Fig. 4a
B
Fig. 3
C

5200AFGMS Ambierle Sofa Table
Assembly Instructions
5200AFGMS —Page 5 —03/14
5. Attach the legs to the Case Assembly with 5/16" Flat Washers (R) and 3/8" x 2-1/2" Hex Bolts
(S). See Figures 5 and 5a.
6. Turn the unit onto its top and using the pocket holes as guides, secure the Shelf Assembly (C)
to the Legs (B) with four #8 x 1-1/4" Pan Head Screws (J). See Figures 6 and 6a.
Fig. 5
Fig. 5a
R
S
x 4
x 4
S
R
Fig. 6
J
x 4
J
Fig. 6a

5200AFGMS Ambierle Sofa Table
Assembly Instructions
5200AFGMS —Page 6 —03/14
7. Turn the table upright insert the Drawers (D). See Figure 7.
8. Place the table at its final destination. To level the table, rotate the Adjustable Glides (O) found
on the bottoms of the leg assemblies. See Figure 7.
Fig. 7
O
O