Wilding Wallbeds PARK CITY User manual

WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND
FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE
PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT. PLEASE CONTACT CUSTOMER SERVICE AT
866-725-6401 FOR ANY QUESTIONS.
Size:
Depth:
Type:
Queen, Full, or Twin
Storage Head Board
Side Mount with 13” Legs 28
Style: Park City
Revision 4.22

Page intentionally left blank

Step Ladder
Studsensor
Ratchet
13mm Socket 11mm Socket 8mm Socket
Large regular screwdriver
Phillips screwdriver
13 mm open end wrench
Stud finder
STANLEY
Tape measure
Cordless screw driver
Tools Needed
Page 1
With Phillips bit

Bed Handles
1
3/8’’
4
2
Qty
Qty
Machine Screw
Hardware Page
Pack 5
5/8’’ Pan head Screw
2
Item Qty
Buckle Strap
1
5/16’’ Nylock
Hex Nut
5/16’’ x 1”
Allen Head Bolt
5/16’’ x 1”
Hex Head Bolt
5/16’’ x 1 1/4’’
16
10
2
4
Pack 2
Qty
Item
1 5/8’’ Pan head
Wood Screw 2
5/16” Allen wrench
Tapered Allen Head Bolt
Panel Saver
2
6’’
2.5’’
(In rails box)
1”x 1” x 1 3/4”
Four Hole Corner
Bracket
10-24 Black
Nylock Nut
10-24 x 1 Black
Machine Screw
1/4’’
5/8’’ Pan
head Screw
10-24 x 1/2’’ Black
Machine Screw
1/2” x 3/4”
Black Barrel
(Leg Stop)
16
2
160
14
2
4
Item
Item
Qty
Qty
Pack 3
Pack 7
Pack 4
1 1/2” x 5/16”
Black washer
1 1/2” X .765”
Black washer
1 1/2” Nylon washer
1/4’’ x 1 1/2’’
Hex Head Bolt
Star Washer
2
2
2
2
4
Item Qty
3/4’’ Washer
2
OR
5.5’’
1.5’’
5mm Allen
wrench
1
Cam Fitting
Connecting Bolts
4
30
Other Hardware
Item Qty
3
Square Tip Bit
1
160
1 1/4” Square
Drive Wood Screw
3 Wood Screw
1/2’’
(Extra)
(From Manila Envelope)
1/4” wood drill bit
1
Page 2

Left Side Board Right Side Board
Finished edge
Cut out for room
base molding
23” 23”
Lift Mechanisms
Bag w/Springs
Hardware pack 2
From Box labeled
SBLM
Step 1: Locate the left and right Side Boards
and then from the small square cardboard box
labelled SBLM locate the two Lift Mechanisms,
hardware bags, and springs.
5/16’’ x 1 1/4’’
X 8
5/16’’ Nylock Nut
X 6
Hardware needed for next step from Pack #2
Repeat step 2 with the Left Side
Board and Lift Mechanism.
IMPORTANT! Over tightening the bolts will
pull the head of the bolt too deeply into the
Side Board. Tighten only until the head of the
bolt is flush with the surface of the Side Board .
Step 2:
Install the Lift Mechanism to
the right Side Board first by inserting a
5/16 x 1 1/4” Tapered Allen head Bolt
through holes A, B, C and D from the
outside (countersunk holes) of the Side
Board. The bolt then goes through the
corresponding holes of the Right Lift
Mechanism as illustrated. Thread on
three 5/16” Nylock nuts and tighten
hardware. Hole “A” has a threaded
collar instead of a nut.
Hole A
Hole B
Hole C
Hole D
Finished Edge
Base Board
Notch
Right
Side Board All holes are
countersunk in
this side of side-
board
Tapered Allen Head Bolt
(Threaded collar)
Page 3

Before you proceed, identify which spring type you have received:
Spring end hooks in opposite direction
Spring end hooks same direction
STOP
Proceed to page 5 - Step 3-A
Page 4
Proceed to page 6 - Step 3-B

Step 3-A: Install required Springs in the Lift Mechanisms
The required number of springs in the Lift Mechanisms varies with the different weights of
mattresses. If you purchased your mattress with your bed from Wilding Wallbeds refer to the
chart to the right. This will also be a good reference point for mattresses not purchased with
your Wall bed.
HELPFUL HINT: Watch how to do this step at:
Install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of the mechanism plate
first then manipulate the Lift Arm back and forth slightly while placing the other end of the spring in the Tension arm into
the corresponding hole. Now place a spring into the following holes in this order 4, 3 then into holes 6, 7. You will need a
total of 5 springs installed for a queen size bed.
Queen
Size Bed
Full
Size Bed
Twin
Size Bed
Upturned edge
of mounting
plate
#1
#9
Tension Arm
#5
Hole
#2
#3
#4
#6
#7
#8
Lift Arm
Install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of the mechanism plate
first then manipulate the Lift Arm back and forth slightly while placing the other end of the spring in the Tension arm
into the corresponding hole. Now place a spring into the following holes in this order 4, then into holes 6. You will need a
total of 3 springs installed for a full size bed.
Install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of the mechanism plate
first then manipulate the Lift Arm back and forth slightly while placing the other end of the spring in the Tension arm into
the corresponding hole. You will need a total of 1 spring installed for a twin size bed.
Page 5
https://youtu.be/2C_Exc_pO-8
Or use the camera on your
phone to view this step.
Hardware needed for next step:
(From box labelled SBLM)
Spring end hooks in opposite direction
Bed Size Number of Springs
Queen
Full/Double
Twin/Single
5
3
1

Bed Size Number of Springs
Queen
Full/Double
Twin/Single
5
3
Step 3-B: Install Springs in the Lift Mecha-
The required number of springs in the Lift Mechanisms varies with the different weights of
mattresses. If you purchased your mattress with your bed from Wilding Wallbeds refer to the
chart to the right. This will also be a good reference point for mattresses not purchased with
your Wall bed.
(4 springs are pre-installed)
Hardware needed for next step:
Lifting Springs
(From box labelled SBLM)
First uninstall the springs from holes 6 and 7 by moving the Lift Arm to a position that allows the springs to come out of
the Tension arm. Next install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of
the mechanism plate and then manipulating the Lift Arm back and forth slightly while sliding the other end of the spring
under the Tension arm and into the corresponding hole. Note:: you may need to bend the spring slightly or lift the tension
arm slightly to get the spring to slip under the Tension Arm. Now put a spring into the following holes 3, 4 and 6, 7. You
will need a total of 5 springs installed for a queen size bed.
Queen
Size Bed
First uninstall the springs from holes 6 and 7 by moving the Lift Arm to a position that allows the springs to come out of
the Tension arm. Next install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of
the mechanism plate and then manipulating the Lift Arm back and forth slightly while sliding the other end of the spring
under the Tension arm and into the corresponding hole. Note: you may need to bend the spring slightly or lift the tension
arm slightly to get the spring to slip under the Tension Arm. Now put a spring into the following holes 6, 7. You will need
a total of 5 springs installed for a full size bed.
Full
Size Bed
Uninstall all of the pre-installed springs by moving the Lift Arm to a position that allows the springs to come out of the
Tension arm. Next install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of
the mechanism plate and then manipulating the Lift Arm back and forth slightly while sliding the other end of the spring
under the Tension arm and into the corresponding hole. Note: you may need to bend the spring slightly or lift the tension
arm slightly to get the spring to slip under the Tension Arm. You will need a total of 5 springs installed for a full size bed.
Twin
Size Bed
1
Page 6
#1
#9
Tension Arm
Upturned edge
of mounting
plate
#5
Hole
#2
#3
#4
#6
#7
#8
Lift Arm
HELPFUL HINT: Watch how to do this process at:
https://www.youtube.com/watch?v=A_KBN5oNGBU
Or use the camera on your
phone to view this step.

Page 7
Hardware needed for next step
Connecting Bolt
X 24
Step 4: Lay the right and left
Side Boards down as illustrated
and screw Connecting Bolts into
the holes provided as illustrated.
Un-finished
Edges
Right Side
Board
Left Side
Board
Note: Screw the connecting
bolts down until the collar of the
connecting bolt is seated firmly
against the surface of the wood.
(From Manila Envelope)
Note: Screw the connecting bolts down
until the collar of the connecting bolt is
seated firmly against the surface of the
wood.

Locate and Identify the Following Parts
(7 Cam Fittings are Pre installed)
Grommet Hole
7.5”
Head Board Bottom
-Board 7.5” wide (length depends on size of the bed).
-2.3/8” Grommet hole in the center of the board.
-7 Pre-installed Cam Fittings.
Identifiers
(4 Cam Fittings are Pre installed
in each)
5”
-Boards are 5” wide (length depends on size of the bed).
-4 Pre-installed Cam Fittings per Stretcher 2 on either end.
Identifiers
Rear Stretcher
6.75”
Hinged Storage Door
(4 Cam Fittings are Pre installed.
Notch
Hinged doors
-Three hinged doors.
-Notch in the door support.
-4 Pre-installed Cam Fittings.
Identifiers
Grommet Hole
23.75”
Bridge Board
-Solid wood Anchor Board.
Identifiers
-23.75” wide (length depends on size of the bed).
Solid wood
Anchor Board.
5mm holes on
three sides.
-5mm holes on three sides.
15”
(6 Cam Fittings are Pre
installed)
5mm holes along edge.
-3 - 5mm holes along one edge.
Identifiers
-Black Barrel
Black Barrel
-15” wide (length depends on size of the bed).
Head Board
Base
Front Stretcher
Front Stretcher and Base
Two Boards connected together
via 3 wing nuts.
Identifiers
Page 8

Step 6: Screw 11 Connecting Bolts
into the holes provided in the Bridge
Board.
Hardware needed for next step
Connecting Bolt
X 11
Solid Wood Anchor
support
Step 5: Screw 3 Connecting Bolts into
the holes on the bottom edge of the Head
Board.
Hardware needed for next step
Connecting Bolt
X 3
(From Manila Envelope)
(From Manila Envelope)
Head Board
Bridge Board
Note: Screw the connecting
bolts down until the collar of the
connecting bolt is seated firmly
against the surface of the wood.
Page 9

1/2 Turn to tight
Cam Fitting
Connecting Bolt
Working with Cam Fittings
In the next steps you will work with Cam Fittings and Connecting Bolts in
attaching cabinet parts together. Take a minute and review this information
for ease of assembly.
- Slide the Cam Fitting over Connecting bolt.
- Hold parts snug together.
- Turn Cam Fitting 1/2 turn clockwise with a manual
screw driver. DO NOT USE POWER SCREW DRIVER.
Step 7 :
Locate the Front Stretcher and Base and remove the three wing nuts and sepa-
rate the two pieces.
Note: Thread the Wing nuts back onto
the base mold to avoid misplacing
them.
Base
Front Stretcher
Page 10

Step 8: Begin assembly of the Bed Cabi-
net face down with the bottom of the bed
nearer the wall to which it will be installed
as illustrated. Connecting the Head Board,
Front and Rear stretchers see illustration.
Head Board
Right Side
Board
Bed Bottom
Left Side Board
Step 9: Insert the Head Board bottom into
position as illustrated. Note the cam fittings
are facing down toward bed bottom.
Bed Bottom
Down
Front Stretcher
Rear Stretcher
Page 11

Step 10: Install the hinged storage door
unit as illustrated.
Helpful hint: Lift the center
section to get the unit posi-
tioned correctly
Bed Bottom
Hinged storage doors
Step 11: Stand the bed cabinet up and
leave 2 feet between cabinet and the wall
so you have space to work behind the bed
INSTALLATION WALL
Page 12

Back
Anchor support
Step 12: Position the Bridge Board as il-
lustrated. Place it on to the Side Boards and
tighten all Cam Fittings.
Front Bridge Support
(6 Cam Fittings are Pre installed).
3”
-Two boards connected together
-6 Pre-installed Cam Fittings.
Identifiers
-3” wide (length depends on size of the bed).
Two boards connected together
Locate and Identify the Following Part
Page 13

Step 13: Attach the Front Bridge Support boards
(two narrow pieces of wood connected together)
by inserting it between the Side Boards and on to
the Connecting Bolts. Tighten all Cam Fittings.
Step 14: With Bed cabi-
net in the standing posi-
tion open the storage head
board on both sides and
insert two 1 1/4” screws
in either side of the lid
support through holes
provided as shown.
Hardware needed for next step
X
1 Wood Screw
1/4’’
(From Manila Envelope)
Page 14

Studs in wall
Step: 15: Using a Stud Finder locate and mark at least 3 studs in the wall behind the
bed cabinet. Pre drill with a 1/4” drill bit (supplied) through the Anchor Support
Board at the back of the Bridge Board corresponding with the studs in your wall.
Using the 3 1/2” wood screws provided anchor the bed cabinet to the wall through
the pre drilled holes.
IMPORTANT! Bed cabinet requires 3
studs, It is VERY important that the bed
cabinet be anchored securely to the wall.
For technical support call 866-725-6401
toll free.
Hardware needed for next step
WARNING! THE NEXT STEP MAY REQUIRE PROFESSIONAL HELP.
IF YOUR WALLS ARE NOT TRADITIONAL WOOD FRAMING, YOU MAY NEED TO HIRE A HANDY
MAN OR CONTRACTOR TO HELP IN ANCHORING THE BED TO YOUR WALL. FAILURE TO PROP-
ERLY ANCHOR THE CABINET COULD CAUSE SEVERE PERSONAL INJURY. CALL TECHNICAL
SUPPORT AT 866-725-6401 IF YOU HAVE ANY QUESTIONS.
With the supplied 1/4” drill
bit. Pre-drill 1/4” holes
through the Anchor Support
board corresponding with the
studs in your wall
3.5” Wood Screws
X 3
1/4” Drill bit (supplied)
(From Manila Envelope)
3.5” Wood Screw
Stud
Page 15

Important note: It is critical to orient the Bed Face panels and the Mattress Rails in the next 5 steps correctly. All of the render-
ings (drawings) in the next 5 steps assume that you are looking away from the wall you just installed the Bed Cabinet against
in the previous step. There is a note under each of the following renderings indicating “your bed cabinet installed on this side”
which indicates that is where the Bed Cabinet is in relation to the face panels and rails.
Your bed cabinet is installed on this side
Step 16: Locate the Front Panels and
lay them on the floor FACE DOWN
(finished side). Position them in
front of where the Bed Cabinet was
installed in the last step and leave
enough room to work around them.
Note that the holes for bed handles
are in the two outside panels and are
arranged more away from the wall the
Bed Cabinet is installed against.
Holes for
handle
Holes for
handle
Head/Foot Rail Inner Side Rail
HELPFUL HINT: Side Mount beds
can be slept on in either direction.
The rails referred to as “Head/Foot
rail” (identical) can act as either the
head or foot of the bed, depending
on which way a sleeper lies.
Step 17: Arrange the Mattress
Rails on the face panels as shown.
Head/Foot Rail
Your bed cabinet is installed on this side
Outer Side Rail
Outer and Inner Side Rails are
identical pieces. In these instruc-
tions they are listed as Outer or
Inner to identify their location on
the Face Panels.
Holes for
handle
Holes for
handle
Page 16

Step 18: From hardware pack 3 locate the hardware shown above. Finger
tighten the hardware as shown in illustration 7 connecting the Outer Side rail
to a Head/Foot rail using a 4 hole corner bracket. Note the lower hole on each
Head/Foot rail uses the Leg Stop with the longer screw (1 1/4” Machine).
Repeat on the opposite side of the Outer Rail corner.
4 hole corner bracket
10-24 Nylock nut
Illustration 7
Step 19: Finger tighten the
hardware as shown in illustra-
tion 8 attaching a 4 hole corner
brackets on the inside of the
Head/Foot Rail and the Panel
Saver on the outside of the Rail.
Now connect the Inner Side Rail
to the Head/Foot rail via the 4
hole corner bracket. Repeat on
the opposite Inner Rail corner.
Step 20: Once all sides
are finger tight go back to
each corner and align the
corners as they are tight-
ened using either a socket
or wrench and a Phillips
screw driver.
Your bed Cabinet installed on this side
Inner Side Rail
10-24 x 1/2” truss head screw
10-24 Nylock nut
4 hole corner bracket
Illustration 8
Panel Saver
Outer Side Rail
Outer Side
Rail
Leg stop (black barrel) 1/2” x 3/4”
10-24 x 1/2” Machine Screw (black)
10-24 x 1 1/4” Machine Screw (black)
Note: The Panel
Savers have 4 holes
but you will only
use two attaching
them to the Head/
Foot Rails.
Head/Foot rail
Inner Side Rail
Hardware needed for next 2 steps most from Pack #3
4 hole corner bracket
X 4 X 2
1/2” x 3/4”
Black Barrel
(Leg Stop)
X
10-24 Black
Nylock Nut
X 2
10-24 x 1 Black
Machine Screw
1/4’’
X 14
10-24 x 1/2’’ Black
Machine Screw
6’’
2.5’’
OR
5.5’’
Panel Saver
(From rails box)
Page 17

BIRDS EYE (TOP) VIEW
Page 18
Frame positioned evenly side to side with wood
face panels protruding by approximately 1” on
either side.
Inner Rail
Outer Rail
Frame inner rail is
flush
with face panels
Handle Holes
Head/Foot Rail
Head/Foot Rail
Handle Holes
Step 21: Center the assembled frame side to side on the Face Panels (leaving ap-
proximately 1” space on either side) and bring the Inner Rail flush to the end of the
Face Panels. Once the frame is positioned correctly and the panels and rails are even
and square to each other use 2 screws (5/8 ”square drive) in each corner, as well as
one in each panel at the Inner and Outer rail to hold assembly in place. With the rails
held in place, Use the 5/8” screws in each of the remaining holes around the frame.
Caution: DO NOT STRIP SCREW!
Hardware and parts needed for next steps
X Approx. 118
5/8” Square Pan head screw
(Hardware pack #7)
OR
5/8” Pan head screw
(Hardware pack #7)
X Approx. 118
(Hardware type varies)