Wilding Wallbeds Remington User manual

Revision 10/20
WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND
FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE
PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT. PLEASE CONTACT CUSTOMER SERVICE AT
866-725-6401 FOR ANY QUESTIONS.
Style:
Size:
Depth:
Type:
Remington
Queen, Full, or Twin
Deep
Side Mount with 13” Legs 27

Step Ladder
Tools Needed
studsensor
Ratchet
13mm Socket 11mm Socket 8mm Socket
Large regular screwdriver
Phillips screwdriver
13 mm open end wrench
Stud finder
STANLEY
Tape measure
Cordless screw driver
With Phillips bit

1” x 1” x 1 3/4”
Four Hole Corner
Bracket
10-24 Black
Nylock Nut
10-24 x 1 Black
Machine Screw
1/4’’
5/8’’ Pan
head Screw
10-24 x 1/2’’ Black
Machine Screw
1/2” x 3/4”
Black Barrel
(Leg Stop)
16
2
160
14
2
4
Item
Item
Qty
Qty
5/16’’ Nylock
Hex Nut
5/16’’ x 1”
Allen Head Bolt
5/16’’ x 1”
Hex Head Bolt
5/16’’ x 1 1/4’’
16
10
2
4
Pack 2
Qty
Item
1 5/8’’ Pan head
Wood Screw 2
5/16” Allen wrench
Pack 3
Pack 7
Panel Saver
2
6’’
2.5’’
(in mechanism rails box)
Tapered Allen Head Bolt
Cam Fitting
Connecting Bolts
4
36
Other Hardware
Item Qty
3
Square Tip Bit
1
160
1 1/4” Square
Drive Wood Screw
3 Wood Screw
1/2’’
(Extra)
(From Manila Envelope)
Hardware Page
Pack 4
1 1/2” x 5/16”
Black washer
1 1/2” X .765”
Black washer
1 1/2” Nylon washer
1/4’’ x 1 1/2’’
Hex Head Bolt
Star Washer
2
2
2
2
4
Item Qty
Pack 5
5/8’’ Pan head Screw
2
Item Qty
1
3/4’’ Washer
2
1/4” wood drill bit
1
Bed Handles
4
1 3/8
Buckle Strap

Step 1: Locate the left and right Side Boards
and then from the small square cardboard box
labelled SBLM locate the two Lift Mechanisms,
hardware bags, and springs.
Left Side Board Right Side Board
Page 1
Finished edge
Cut out for room
base molding
Lift Mechanisms
Bag w/Springs
Hardware pack 2
From Box labeled
SBLM
5/16’’ x 1 1/4’’
x 8
5/16’’ Nylock Nut
x 6
Hardware needed for next step from Pack #2
Repeat step 2 with the Left Side
Board and Lift Mechanism.
IMPORTANT! Over tightening the bolts will
pull the head of the bolt too deeply into the
Side Board. Tighten only until the head of the
bolt is flush with the surface of the Side Board .
Step 2:
Install the Lift Mechanism to
the right Side Board first by inserting a
5/16 x 1 1/4” Tapered Allen head Bolt
through holes A, B, C and D from the
outside (countersunk holes) of the Side
Board. The bolt then goes through the
corresponding holes of the Right Lift
Mechanism as illustrated. Thread on
three 5/16” Nylock nuts and tighten
hardware. Hole “A” has a threaded
collar instead of a nut.
Hole A
Hole B
Hole C
Hole D
Finished Edge
Base Board
Notch
Right
Side Board All holes are
countersunk in
this side of side-
board
Tapered Allen Head Bolt
(Threaded collar)
19 7/8” 19 7/8”

Page 2
Bed Size Number of Springs
Queen
Full/Double
Twin/Single
5
3
Step 3: Install Springs in the Lift Mechanisms
The required number of springs in the Lift Mechanisms varies with the different weights of
mattresses. If you purchased your mattress with your bed from Wilding Wallbeds refer to the
chart to the right. This will also be a good reference point for mattresses not purchased with
your Wall bed.
(4 springs are pre-installed)
Hardware needed for next step:
Lifting Springs
HELPFUL HINT: Watch how to do this process at:
https://www.youtu.be/A_KBN5oNGBU
See step 3 of the video to view installation of springs.
(from box labelled SBLM)
First uninstall the springs from holes 6 and 7 by moving the Lift Arm to a position that allows the springs to come out of
the Tension arm. Next install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of
the mechanism plate and then manipulating the Lift Arm back and forth slightly while sliding the other end of the spring
under the Tension arm and into the corresponding hole. Note:: you may need to bend the spring slightly or lift the tension
arm slightly to get the spring to slip under the Tension Arm. Now put a spring into the following holes 6, 7, 8 and 2. You
will need a total of 7 springs installed for a queen size bed.
#1
#9
Tension Arm
Upturned edge
of mounting
plate
#5
Hole
#2
#3
#4
#6
#7
#8
Lift Arm
Queen
Size Bed
First uninstall the springs from holes 6 and 7 by moving the Lift Arm to a position that allows the springs to come out of
the Tension arm. Next install a spring into hole 5 by hooking one end of the spring into the hole on the Upturned edge of
the mechanism plate and then manipulating the Lift Arm back and forth slightly while sliding the other end of the spring
under the Tension arm and into the corresponding hole. Note: you may need to bend the spring slightly or lift the tension
arm slightly to get the spring to slip under the Tension Arm. Now put a spring into the following holes 6, and 7. You will
need a total of 5 springs installed for a full size bed.
Full
Size Bed
Uninstall the spring from hole 7 by moving the Lift Arm to a position that allows the springs to come out of the Tension
arm. You will now have a Spring in holes 3,4 and 6 for a total of 3 springs.
Twin
Size Bed
1

Page 3
RIGHT
LEFT
Hardware needed for next step:
x 20
Connecting Bolt
(From Manila Envelope)
Step 4: Lay the right and left Side
Boards down as illustrated and
screw the Connecting Bolts into the
holes provided as illustrated.
Note: Screw the connecting bolts down
until the collar of the connecting bolt is
seated firmly against the surface of the
wood.

Page 4
Step 5 A:
Locate the Front Stretcher and Base and remove the three wing nuts and
separate the two pieces.
Base
Front Stretcher
Note: Thread the Wing nuts back onto
the base mold to avoid misplacing
them.
Hardware needed for next step:
x 3
Connecting Bolt
(From Manila Envelope)
Step 5 B:
Locate the Headboard Shelf and insert 3 connecting bolts into the holes
provided as illustrated.

Page 5
Step 5:
Assemble the Bed Cabinet face down as illustrated with the bottom of the Bed
Cabinet nearer the wall in which it will be installed.
IMPORTANT! Tighten the cam fittings with a hand screw driver by turning the
Phillips head clockwise 1/2 turn to tight.
HELPFUL HINT: It is easier to tighten the Cam Fittings if the two bed parts are
snug together.
Illustration 5
1/2 Turn to tight
Cam Fitting
Connecting Bolt
Rear Stretcher
Head Board Side Boards
Bed Bottom
Step 6: Stand the bed cabinet up and leave
2 feet between cabinet and the wall so you
have space to work behind the bed
INSTALLATION WALL
Front Stretcher
Headboard Shelf

Page 6
Back
Anchor support board
Step 8: Position the Bridge Board as
illustrated below. Place it on to the Side
Boards and tighten all Cam Fittings.
Finished edge
Step 7: Locate the Bridge Board and
Insert 11 Connecting Bolts into the
holes provided.
Hardware needed for next step
Connecting Bolt
x 11
Bridge Board Receives 11
Connecting Bolts
Solid Wood Anchor
support

Page 7
Step 9: Locate the Front Bridge Support boards
(two narrow pieces of wood connected together)
and insert it between the Side Boards and on to the
Connecting Bolts. Tighten all Cam Fittings.

Step: 10: Using a Stud Finder locate and mark at least 3 studs in the wall behind the
bed cabinet. Pre drill with a 1/4” drill bit (supplied) through the Anchor Support
Board at the back of the Bridge Board corresponding with the studs in your wall.
Using the 3 1/2” wood screws provided anchor the bed cabinet to the wall through
the pre drilled holes.
IMPORTANT! Bed cabinet requires 3
studs, It is VERY important that the bed
cabinet be anchored securely to the wall.
For technical support call 866-725-6401
toll free.
Hardware needed for next step
Page 8
WARNING! THE NEXT STEP MAY REQUIRE PROFESSIONAL HELP.
IF YOUR WALLS ARE NOT TRADITIONAL WOOD FRAMING, YOU MAY NEED TO HIRE A HANDY
MAN OR CONTRACTOR TO HELP IN ANCHORING THE BED TO YOUR WALL. FAILURE TO PROP-
ERLY ANCHOR THE CABINET COULD CAUSE SEVERE PERSONAL INJURY. CALL TECHNICAL
SUPPORT AT 866-725-6401 IF YOU HAVE ANY QUESTIONS.
With the supplied 1/4” drill
bit. Pre-drill 1/4” holes
through the Anchor Support
board corresponding with the
studs in your wall
Studs in wall
3.5” Wood Screw
Stud
3.5” Wood Screws
x 3
1/4” Drill bit (supplied)
(From Manila Envelope)

Head/Foot Rail Inner Side Rail
HELPFUL HINT: Side Mount beds
can be slept on in either direction.
The rails referred to as “Head/Foot
rail” (identical) can act as either the
head or foot of the bed, depending
on which way a sleeper lies.
Step 12: Arrange the Mattress
Rails on the face panels as shown.
Head/Foot Rail
Your bed cabinet is installed on this side
Your bed cabinet is installed on this side
Page 9
Holes for
handle
Holes for
handle
Outer Side Rail
Outer and Inner Side Rails are
identical pieces. In these instruc-
tions they are listed as Outer or
Inner to identify their location on
the Face Panels.
Important note: It is critical to orient the Bed Face panels and the Mattress Rails in the next 5 steps correctly. All of the render-
ings (drawings) in the next 5 steps assume that you are looking away from the wall you just installed the Bed Cabinet against
in the previous step. There is a note under each of the following renderings indicating “your bed cabinet installed on this side”
which indicates that is where the Bed Cabinet is in relation to the face panels and rails.
Step 11: Locate the Front Panel(s)
and lay them on the floor FACE
DOWN (finished side). Position them
in front of where the Bed Cabinet
was installed in the last step and leave
enough room to work around them.
Note that the holes for bed handles
are arranged together and more away
from the wall the Bed Cabinet is
installed against.

Step 13: From hardware pack 3 locate the hardware shown above. Finger
tighten the hardware as shown in illustration 7 connecting the Outer Side rail
to a Head/Foot rail using a 4 hole corner bracket. Note the lower hole on each
Head/Foot rail uses the Leg Stop with the longer screw (1 1/4” Machine).
Repeat on the opposite side of the Outer Rail corner.
4 hole corner bracket
10-24 Nylock nut
Illustration 7
Step 14: Finger tighten the
hardware as shown in illustra-
tion 8 attaching a 4 hole corner
brackets on the inside of the
Head/Foot Rail and the Panel
Saver on the outside of the Rail.
Now connect the Inner Side Rail
to the Head/Foot rail via the 4
hole corner bracket. Repeat on
the opposite Inner Rail corner.
Step 15: Once all sides
are finger tight go back to
each corner and align the
corners as they are tight-
ened using either a socket
or wrench and a Phillips
screw driver.
Your bed Cabinet installed on this side
Inner Side Rail
4 hole corner bracket
Hardware needed for next 2 steps most from Pack #3
x 4 x 2
10-24 x 1/2” truss head screw
10-24 Nylock nut
4 hole corner bracket
Illustration 8
Page 10
Panel Saver
Outer Side Rail
Panel Saver
(From rails box)
1/2” x 3/4”
Black Barrel
(Leg Stop)
x 16
10-24 Black
Nylock Nut
x 2
10-24 x 1 Black
Machine Screw
1/4’’
x 14
10-24 x 1/2’’ Black
Machine Screw
6’’
2.5’’
Outer Side
Rail
Leg stop (black barrel) 1/2” x 3/4”
10-24 x 1/2” Machine Screw (black)
10-24 x 1 1/4” Machine Screw (black)
Note: The Panel
Savers have 4 holes
but you will only
use two attaching
them to the Head/
Foot Rails.
Head/Foot rail
Inner Side Rail

Frame positioned evenly side to side with wood
face panels protruding by approximately 1” on
either side.
Inner Rail
Outer Rail
Frame inner rail is
flush with face panels
Handle Holes
Step 16: Center the assembled frame side to side on the Face Panels (leaving ap-
proximately 1” space on either side) and bring the Inner Rail flush to the end of the
Face Panels. Once the frame is positioned correctly and the panels and rails are even
and square to each other use 2 screws (5/8 ”square drive) in each corner, as well as
one in each panel at the Inner and Outer rail to hold assembly in place. With the rails
held in place, Use the 5/8” screws in each of the remaining holes around the frame.
Head/Foot Rail
Head/Foot Rail
Caution: DO NOT STRIP SCREW!
Hardware and parts needed for next steps
x 160
5/8” Square Pan head screw
(Hardware pack #7)
x 1
BIRDS EYE (TOP) VIEW
Page 11
(Provided in Manila Envelope)
Square Tip Bit
Handle Holes

Hardware and parts needed for next steps
Wood Mattress
Support
x 3
x 2
1 1/4” Square drive
Wood screw
5/8” Square Pan head screw
(Hardware pack #7)
Square Tip Bit
x 1
Metal Center Stiffeners
Step 17: Position the Wood Mattress Supports evenly over the Face Panel
seams allowing their ends to over lap the Outer and Inner Rails. Use the 1 1/4”
wood screws through the holes provided in the Mattress Support to mend the
Face Panels together. DO NOT STRIP SCREWS.
Helpful hint: Mattress Supports may have an area cut
out to allow for the bed handle holes.
Step 18: Position the 2 Metal Stiffeners evenly in the space provided be-
tween the outer and center Wood Mattress Supports as illustrated below. Now
use the 5/8” square drive screws to fasten the Stiffeners to the Face Panels.
DO NOT STRIP SCREWS.
Page 12
(Provided in Manila Envelope)
Wood mattress
supports positioned
evenly over seems
Inner Rail
Outer Rail
Holes or
Cut out to
provide
opening
for handle
holes
Metal Center Stiffeners
1 1/4” Square drive
Wood screw
5/8” Square Pan
head screw
BIRDS EYE (TOP) VIEW
5/8” Square Pan
head screw
1 1/4” Square drive
Wood screw

x 2
3/4” Washer (pack #5)
Hardware and parts needed for next steps
Square Tip Bit
x 1
Inner Rail
Head/Foot Rail
Head/Foot Rail
Buck-
leStrap
anchor
locations
18” +/-
BIRDS EYE (TOP) VIEW
Page 13
(Provided in Manila Envelope)
Outer Rail
3/4”
Washer
5/8”
Screw
Buckle Strap
Buckle
Strap
x 1
Buckle Strap (pack #5)
Step 19; Attach the Buckle Strap used
for holding the mattress in place when
the bed is closed. First remove one of the
5/8” Pan head screws that attaches the
rail to the Face Panels on each Side Rail
of the frame at about 18” from the Foot
Rail of the frame. Then put the removed
screw through the 3/4” Washer. Posi-
tion the end of the Strap over the vacated
screw hole on the rail and drive the screw
through the strap and back into the hole.
Repeat the process on the opposite Side
Rail.

Step 20: As illustrated below, insert the Allen Head Bolt through bolt hole # 1 and tighten it down securely using a Nylock Nut.
Now insert a 5/16” x 1” Hex head bolt through hole # 3 and thread the Nylock nut ONLY UNTIL THE NUT IS FLUSH WITH
THE END OF THE BOLT. Bolt hole #2 will be used in a later step and is left open for now.
Hardware needed for next step from hardware pack #2
5/16” Nylock Nut
X 4 X 2 X 2
5/16” x 1” Allen Head Bolt
Inner Side Rail
Bolt hole 1
Bolt hole 3
Bolt hole 2 (left open)
6.75”
Page 14
Hardware needed for next step from hardware pack #4
Step 21: Attach the Leg Assembly to the OUTER RAIL side of the frame as illustrated below. Use
1 Teflon washers on the out side of the frame for proper spacing.
X 2
1/4” x 1 1/2”
X 2
Star Washer
Step 22: Position the Cross Bar between the Legs. Place the Star washer on one of the 1/4” X 1 1/2” Hex Head bolts. Repeat on
other side.
Cross Bar
Outer Side Rail
Leg Stop
1 1/2” x .765
1 1/2 Nylon washer
X 4 X 2 X 2
1 Thin Teflon washer 1 Thin Teflon washer
5/16” x 1”
Hex Head Bolt
1 1/2” x 5/16” Black
washer

WARNING: There is tremendous force involved in the next step, do not place hands be-
tween the front of the side boards and the tension arms as you set the mechanism.
Helpful hint: As you start to draw the
Tension Arm down with one hand, use
the other hand to position the Arm Lock
on top of the Hex Nut. Now as the Ten-
sion Arm continues to be pulled down
with both hands, the Arm Lock will
naturally drop into place around the
Hex Nut as illustrated.
Tension Arm
Arm Lock
Hexagon Nut
Black Metal Tube
Black Metal Tube
Step 23: Brace one foot against the front edge
of the Side Board and using the 14.5” black metal
tubing provided in hardware kit, lever the Lift
Mechanism’s Tension Arm out and down until
you can secure the Arm Lock onto the Hexagon
Nut shown at right. BE SURE THAT THE LOCK
IS SECURED AGAINST THE HEX NUT BE-
FORE RELEASING THE TENSION ON THE
LIFT MECHANISM.
Step 24: Slip the Mechanism Cover
over the Mechanism so that the tabs on
the cover fit into the notches provided.
Line up the top hole with the barrel
support and anchor in place using the
3/16” x 1 1/4” wood screw provided
Head Board
Black mechanism cover
3/16’’x 1 Black
Wood Screw
1/4’’
2
Hardware needed for next step from hardware pack #2
Helpful hint: The screw for
attaching the spring cover is
a wood screw not a machine
screw and is in hardware
pack #2.
Page 15

Page 16
Step 25: Stand the Bed face unit up
on its Inner Side Rail. Now with you
and your assistant on either side of
the Bed unit lift until the # 3 bolt on
the Head/Foot Rail is a few inches
above the slotted end of the Tension
Arm on both sides. Gently lower the
Bed Face unit between the Tension
Arms and seat the # 3 bolt into the
slot at the end of the Tension Arms.
Now start pulling the bed face unit
down and away from the Bed Cabinet
the Allen Head bolt will naturally
seat into the notch at the lower end
of the Tension Arms. Lower the bed
unit down and extend the Legs so that
they are on the floor. Someone will
need to hold the bed unit down as it
will want to rise.
IMPORTANT! As instructed in step 20, Bolt #3 should be loose enough to slip into
the notch at the end of the Tension Arm See illustration below.
Bed Face
#3 Bolt head
Allen Key bolt head
Lift Arm
Head Rail