Wilding Wallbeds SANTA FE User manual

WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND
FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SE-
VERE PERSONAL INJURY TO USER OR DAMAGE TO PRODUCT. PLEASE CONTACT CUSTOMER
SERVICE AT 866-725-6401 FOR ANY QUESTIONS.
Rev 3.20
INSTRUCTION BOOKLET #C183
Watch step by step installation instructions at:
https://www.wallbedsbywilding.com/wallbed-installation-studio-series/
WILDING WALLBEDS
SANTA FE MODEL
INSTALLATION INSTRUCTIONS
STORAGE HEAD BOARD

Studsensor
Ratchet
13mm Socket 11mm Socket 8mm Socket
Large regular screwdriver
Phillips screwdriver
13 mm open end wrench
Stud finder
STANLEY
Tape measure
Cordless screw driver
With Phillips bit
6 foot ladder
Tools Needed

Hardware Page
Pack 5
5/8’’ Pan head Screw
2
Item Qty
2
5/16’’ Nylock
Hex Nut
5/16’’ x 1”
Allen Head Bolt
5/16’’ x 1”
Hex Head Bolt
5/16’’ x 1 1/4’’
16
10
2
4
Pack 2
QtyItem
1 5/8’’ Pan head
Wood Screw 2
5/16” Allen wrench
Tapered Allen Head Bolt
Panel Saver
2
6’’
2.5’’
(In mechanism rails box)
1”x 1” x 1 3/4”
Four Hole Corner
Bracket
10-24 Black
Nylock Nut
10-24 x 1 Black
Machine Screw
1/4’’
5/8’’ Pan
head Screw
10-24 x 1/2’’ Black
Machine Screw
1/2” x 3/4”
Black Barrel
(Leg Stop)
16
2
160
14
2
4
Item
Item
Qty
Qty
Pack 3
Pack 7
Pack 4
1 1/2” x 5/16”
Black washer
1 1/2” X .765”
Black washer
1 1/2” Nylon washer
1/4’’ x 1 1/2’’
Hex Head Bolt
Star Washer
2
2
2
2
4
Item Qty
3/4’’ Washer
2
10
1 Wood Screw
1/4’’
Cam Fitting
Connecting Bolts
4
34
Other Hardware
Item Qty
“L” Bracket
3
6
5/8’’ Pan head Screw
2.5’’ Wood Screw
6
Square Tip Bit
1
(Extra)
(From Manila Envelope)
Bed Handles
1
3/8’’
4
2
Qty
Qty
Machine Screw
Velcro or Buckle
Retainer Straps

Left Side Board Right Side Board
Lift Mechanism
Finished edge
Cut out for room
base molding
Step 1: Locate the two Side Boards. If you pur-
chased a King or Queen size bed the Side Boards
measure 85.25” long. Then from the small square
cardboard box labelled SBLM, locate the two Lift
Mechanisms, hardware bags, and springs.
Page 1
5/16’’ x 1 1/4’’
x 8
5/16’’ Nylock Nut
x 8
Hardware needed for next step from Pack #2
Repeat step 2 with the Left Side
Board and Lift Mechanism.
IMPORTANT! Over tightening the nuts will
pull the head of the bolt too deeply into the
Side Board. Tighten only until the head of the
bolt is flush with the surface of the Side Board .
Step 2: Install the Lift Mechanism to
the right Side Board first by inserting a
5/16 x 1 1/4” Tapered Allen head Bolt
through holes A, B, C and D from the
outside (countersunk holes) of the Side
Board. The bolt then goes through the
corresponding holes of the Right Lift
Mechanism as illustrated. Thread on
four 5/16” Nylock nuts and tighten
hardware. (hole A may have threaded
collar instead of bolt)
May be threaded
collar instead of
bolt in hole A.
Note:
Hole A
Hole B
Hole C
Hole D
Finished Edge
Base Board
Notch
Right
Side Board All holes are
countersunk in
this side of side-
board
Tapered Allen Head Bolt

Page 2
Step 3: Install Springs in the Lift Mechanisms
HELPFUL HINT: Watch how to do this process at:
IMPORTANT! Be sure that holes
of the Mounting Plate correspond
to the holes in the Tension Arm
and use the same number of
springs and the same configura-
tion on both Lift Mechanisms
Repeat Step 3 for Left Lift Mechanism.
Install the first spring in hole #5 (if mechanism has some pre-loaded springs from the factory, remove lower springs first)
on both the Mounting Plate and the Tension Arm. Hook one end of the spring under the upturned edge of the Mounting
Plate first then lay the spring down and slide it under the matching hole in the Tension Arm. See illustration 1.
Continue by working up one hole in
the lifting mechanism, then down one
hole alternating back and forth until all
springs are loaded.
NOTE: After you have completed installing and checking operation of your Wall bed, you
may find it necessary to add or remove springs to achieve the correct lift effort of between
5 and 10 pounds.
The required number of springs in the Lift Mechanisms varies with the different weights of
mattresses. If you purchased your mattress with your bed from Wilding Wallbeds refer to the
chart to the right. This will also be a good reference point for mattresses not purchased with
your Wall bed.
(Some springs may be pre-installed)
https://www.wallbedsbywilding.com/wallbed-installation-studio-series/
Hardware needed for next step:
Hole #5
Hole #1
Hole #9
Tension Arm
Upturned edge
of mounting
plate
Arm Bracket
Illustration 1
(Right lift mechanism)
Lifting Springs
See step 4 of the video to view installation of springs.
(from box labelled SBLM)
Bed Size Number of Springs
Queen
Full/Double
Twin/Single
7
6
4

Page 3
Step 4: Lay the right Side Board down and screw 14 Connecting Bolts into
the holes provided as shown. Repeat the process with the left Side Board
which will require 15 Connecting Bolts.
Hardware needed for next step:
x 29
Connecting Bolt
Note: Screw the connecting bolts down until the collar of the con-
necting bolt is seated firmly against the surface of the wood.
(From Manila Envelope)
One in each
of the 7 holes
LEFT
One in each
of the 7 holes
RIGHT

Page 4
1/2 Turn to tight
Cam Fitting
Connecting Bolt
Storage Head board step A: Locate the
Head Board and insert 3 Connecting Bolts
into the holes at the bottom edge of the
Head Board.
Storage Head board step B: Identify
the Head Board Bottom which has 7 Cam
fittings pre-installed and a grommet hole in
the center.
Working with Cam Fittings
In the next three steps you will work with Cam Fittings and Connecting
Bolts in attaching cabinet parts together. Take a minute and review this
information for ease of assembly.
- Slide the Cam over Connecting bolt.
- Hold parts snug together.
- Turn Cam Fitting 1/2 turn clockwise with a manual
screw driver. DO NOT USE POWER SCREW DRIVER.
Storage Head board Steps
(Cam Fittings are Pre installed)
(Cam Fittings are Pre installed)
Hardware needed for next step:
x 3
Connecting Bolt
(From Manila Envelope)

Page 5
Bed Bottom
Front Stretcher
cam fittings on bottom
Optional holes
for lights
Head Board
Bridge Board
Left Side Board
Right Side Board
Storage Head Board Step C: Insert
the Head Board bottom into position as
illustrated. Note the cam fittings are fac-
ing down toward the bottom of the bed
cabinet.
Storage Head Board Step D: Install the
hinged storage door unit as illustrated.
Helpful hint: Lift the center
section of the hinged storage
door to get the unit positioned
correctly.
Hinged storage doors
Bed Bottom
Down
Storage Head board steps
Step 5:
Assemble the Bed Cabinet
face down with the bottom of the Bed
Cabinet nearer the wall to which it will
be installed. Note the “Front Stretcher”
(illustrated to right) should be positioned
so the Cam Fittings are at the bottom of
the Bed Cabinet
.

Step 6: Stand the Bed Cabinet
up against the wall where you
intend to have it installed.
Page 6
INSTALLATION WALL
(Light Kit instructions are in the Light Kit box)
STOP IF YOU PURCHASED LIGHTS FOR YOUR WALLBED YOU MUST REFER TO THE
LIGHT KIT INSTRUCTIONS AND INSTALL THE LIGHT KIT BEFORE MOVING ON.
Storage Head Board Step
E: With Bed Cabinet in the
standing position open the
storage head board on both
sides and insert two 1 1/4”
screws in either side of the lid
support through holes pro-
vided as shown.
Storage Head board step
X 4
1 Wood Screw
1/4’’
Hardware needed for next step
(From Manila Envelope)