Wilson Electronics 301101 User manual

Antenna
Installation
Guide
Features:
• Dual band (for the 301101: 800 / 1900 MHZ)
(for the 301701: 900/1800 MHz)
• Analog and digital
• Improves voice and data signal quality
• Mobile, Marine and In-Building use
• Mounting options available for any application
• Built-in ground plane allows for mounting on any surface
Wilson
®
Electronics, Inc.
Trucker
Mirror Mount
Cellular Antenna
PART# 301101
301701

1Contact Wilson’s Technical Support Department with any questions at 877-594-5766
Or email: [email protected] Hours: 7am to 6 pm MST..
2
How It Works
Wilson Electronics Trucker Mirror-Mount Cellular Antenna will collect the cell
tower signal and send it through the cable to a signal booster or directly to the
cell phone or laptop data card. When the cell phone or data card transmits, the
signal is transferred to a signal booster or directly to the antenna and broadcast
back to the cell tower.
Antenna Adapter Required – Sold Separately
A phone/data card-specic, six-inch antenna adapter is required when
connecting the antenna directly to a cell phone. To identify the correct adapter,
see Wilson Electronics Adapter Guide
at www.wilsonelectronics.com or call
Technical Support at 877-594-5766.
Adapter type may vary depending on
your cell phone or laptop data card.
Installing the Antenna
CAUTION: If you used a knife to
remove the Trucker antenna from the
packaging, check to make sure that
you did NOT cut the antenna cable.
Screw the six antenna radials into the
holes under the plastic coil housing
on the antenna. The included thread-
locker liquid must be used to ensure
the radials do not vibrate loose.
Tighten the radials snugly with a
wrench.
Wilson Electronics Signal Boosters Amplify Coverage Even More
A Wilson Electronics signal booster (sold separately), when used in conjunction
with your antenna, can improve your cell phone and laptop data card coverage
area up to 50 miles. Wilson Electronics manufactures a wide range of wireless
and direct-connection signal boosters for mobile or in-building use. See your
dealer for details or visit www.wilsonelectronics.com.

1
2
Contact Wilson’s Technical Support Department with any questions at 877-594-5766
Or email: [email protected] Hours: 7am to 6 pm MST..
Disclaimer: The information provided by Wilson Electronics, Inc. is
believed to be complete and accurate. However, no responsibility is
assumed by Wilson Electronics, Inc. for any business or personal losses
arising from its use, or for any infringements of patents or other rights of
third parties that may result from its use.
Copyright © 2010 Wilson Electronics, Inc. All rights reserved.
Warning: Verify that both the outside antenna and the adapter extension
cable are connected to the signal booster before powering up the signal
booster.
!
For best performance, it is important
to install the antenna as high on the
truck cab as possible. The radials
should be no lower than the top of the
truck cab. We recommend that when
using a Wilson Electronics mobile
wireless signal booster, to install
the trucker antenna on the top, rear
area of the cab, the grab bar or the
headache rack.
Install the antenna at least 8 inches
away from any other antennas
to avoid interference. To avoid
impact damage, Wilson Electronics
recommends installing the antenna
on the driver’s side with a spring
between the antenna and the mount.
Impact damage is NOT covered under
warranty. Any antenna mount that has
a standard 3/8” x 24-thread female
receptacle will work with the trucker
antenna.
Secure the antenna onto the mount
by tightening with a 9/16” wrench.
CAUTION: DO NOT over tighten.
Route the cable from the trucker
antenna to the cell phone/cellular data
card adapter (sold separately) or to the
signal booster’s connector.
Extension cables up to 10 feet in
length are available. (sold separately)

Wilson
®
Electronics, Inc.
Antenna Specications
Part Number 301101 301701
Frequency Range 800/1900 MHz 900/1800 MHz
Impedance 50 ohms
Antenna Gain 5.12 dBi 806-894 MHz /
6.12 dBi 1850-1990 MHz
5.12 dBi 880-960 MHz /
6.12 dBi 1710-1880 MHz
Radiation Omni
Polarization Vertical
Wavelength 0.9 Wavelength 806-894 MHz /
1.95 Wavelength 1850-1990 MHz
0.9 Wavelength 880-960 MHz /
1.95 Wavelength 1710-1880 MHz
Ground Plane Built-in Ground Plane
Connector FME Female
Material Whip - Stainless Steel / Extension - Fiberglass
Coax Cable RG58 - 10.5 feet / 3.2 meters
Height 32.0625 inches / 81.45 cm
Mount Standard CB 3/8 inch x 24 thread
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back
guarantee. If, for any reason, the performance of any product is not acceptable, simply
return the product directly to the reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics Trucker Mirror Mount Dual-Band Cellular Antenna is warranted
for one (1) year against defects in workmanship and / or materials. Warranty cases
may be resolved by returning the product directly to the reseller with a dated proof of
purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense,
with a dated proof of purchase and a Returned Material Authorization (RMA) number
supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair or
replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer.
This warranty does not apply to any antennas determined by Wilson Electronics to
have been subjected to misuse, abuse, neglect, or mishandling that alters or damages
physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 877-594-5766.
3301 East Deseret Drive, St. George UT 84790
For additional Technical Support visit www.wilsonelectronics.com
or email at: [e-mail]
Phone: [phone] Local: 507-282-8484 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Part # 104030 AIG TRU 005 / 01.04.11