Wilson Electronics 301130 User manual

Antenna
Installation
Guide
Features:
• High-performance, omni-directional antennna
• Built-in radial ground plane
• Coupler included for different mounting options
• Fiberglass-encased and weatherproof
• Fits standard 1-inch x 14 threaded mount
• For mobile or fixed locations
Multi-Band
Marine
Antenna
PART# 301130
Coupler
Included

1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
2
Antenna Adapter Required – Sold Separately
A phone/data card-specific Antenna Adapter is required when connecting the antenna directly
to a cell phone or laptop data card. To identify the correct adapter, see Wilson Electronics
Adapter Guide at www.WilsonElectronics.com or call Technical Support at 866-294-1660.
Adapter type may vary depending on
your cell phone or laptop data card.
Package Contents Include
1 - Multi-Band Marine Antenna
1 - mounting coupler
6 - radials (3 short, 3 long)
1 - thread-locker liquid
1 - plastic cable wrench
Thank You For Purchasing a Wilson Electronics Antenna.
Please read all instructions before installing and check the parts supplied against those
listed in this guide. Wilson Electronics weatherproof fiberglass-encased antenna is omni-
directional and ideal for many marine applications including small boats, cabin cruisers
and yachts as well as RVs, offices and homes. It has the highest gain allowed for a mobile
antenna and has a built-in radial ground plane for maximum performance.
Our innovative design results in high efficiency and low signal loss, which means more
signal to your cellular device. This performance-based marine antenna is backed by
Wilson Electronics 30-day money-back guarantee and 1-year warranty.
Carefully Determine Your Mounting Location
The Wilson Electronics Marine Antenna should be mounted as high as possible with no
obstructions. Marine antennas work on a “line-of-sight” basis, so the higher your antenna
is, the farther it can receive a signal. This gives you a greater range for your cellular
communications.
There is a compromise between installing the antenna as high as possible and keeping the
cable run short to reduce signal loss. For cable runs under 20 feet (recommended), Wilson
Electronics has various RG-58 cable lengths and connectors available (sold separately).
If cable length over 20 feet is needed, we recommend increasing the cable size to Wilson 400
or low loss cable to reduce signal loss. Make sure your mounting location is as far away as
possible from other antennas and upright objects like masts. Be careful not to kink or crush
the antenna cable or bend it tightly around obstructions during installation. This can lead to
poor performance and signal loss.
For assistance with your installation, call Wilson Electronics Technical Support toll free at
866-294-1660 Monday through Friday between 7:00 a.m. and 6:00 p.m. MST, or visit
www.WilsonElectronics.com. Wilson Electronics is closed Saturday, Sunday and holidays.
Vertical Placement
Vertical placement is very important for proper operation. There may be a desire to angle
the antenna backwards for aesthetic reasons. However, not having the antenna mounted
vertically decreases its performance.
A general “rule of thumb” for placement is to install all antennas at least an antenna’s
length away from other antennas. If there is not enough separation between antennas
RF Safety Warning: The outside antenna must be
installed with a separation of at least 16 inches from
any of the vessel’s occupants or nearby persons and
must not be located or operating in conjunction with
any other antenna or signal booster.
!

1
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: [email protected]. Hours: 7 am to 6 pm MST.
1.
2.
1. First, attach the antenna to the coupler.
2. Then, attach the coupler to the mount.
!Allow the cable to turn freely when
attaching or damage may occur!
(especially when using a wireless signal booster), then
oscillation (feedback) may occur causing the signal
booster to power down.
Assembling and Attaching the Antenna
Screw the six radials into the holes near the base of
the antenna (see diagram). Note: The hole size is
different between the short and long radials. Tighten
the radials snugly with a wrench. DO NOT over
tighten. The included liquid thread lock must be used
to ensure the radials do not vibrate loose.
Use the 1” 14-thread coupler (included) to attach the
antenna to any standard marine mounting bracket.
The coupler provides a feed through for routing
the connecting cable, which will run to your cellular
device, or Wilson Electronics signal booster.
Once the antenna is properly attached to the mounting
bracket, attach the connecting cable (sold separately)
to the antenna’s 7” pigtail cable and route it to the
location of your cellular device. Use the appropriate
adapter for your cellular device (sold separately). If
you are using a Wilson Electronics signal booster,
carefully follow the instructions included with the
model purchased.
Warning: Damage will occur to the cable when the antenna
is attached to the coupler if the cable is not allowed to turn freely.
!
7” Coax
Cable
Antenna
Base
Coupler
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to be
complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc.
for any business or personal losses arising from its use, or for any infringements of patents
or other rights of third parties that may result from its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.

Antenna Specifications
Part Number 301130
Frequency Range 700-800 MHz / 824-894 MHz / 880-960 MHz /
1710-1880 MHz / 1850-1990 MHz
Impedance 50 ohms
Antenna Gain 3.4 dBi 700-800 MHz / 4.1 dBi 824-894 MHz / 3.5 dBi 880-960 MHz /
3.1 dBi 1710-1880 MHz / 5.1 dBi 1850-1990 MHz
Radiation Omni
Polarization Vertical
Ground Plane Built-in Ground Plane
Connector FME Female
Material Whip - Stainless Steel / Casing - Fiberglass
Coax Cable RG58 - 7 inches
Height 21 inches / 53.3 cm
Mount Standard 1-inch x 14 thread
Part #103010 AIG 11 / 06.06.11
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: [e-mail]
Phone: [phone] Local: 435-673-5021 Fax: [phone]
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day
money-back guarantee. If for any reason the performance of any product is not
acceptable, simply return the product directly to the reseller with a dated proof of
purchase.
1-Year Warranty
Wilson Electronics Multi-Band Marine Antenna is warranted for one (1) year against
defects in workmanship and/or materials. Warranty cases may be resolved by
returning the product directly to the reseller with a dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its
option, either repair or replace the product. Wilson Electronics will pay for delivery
of the repaired or replaced product back to the original consumer.
This warranty does not apply to any antennas determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660 or
e-mail [e-mail] or visit www.WilsonElectronics.com.