Wilson Electronics 311230 User manual

Installation Guide
Drive RV Antenna

Index
Package Contents ............................................................1
Select Mounting Location .................................................... 2
Assemble the Antenna ........................................................3
Mounting the Antenna ....................................................... 5
Safety Guidelines & Specifications ............................................ 6
Warranty ....................................................................7

1
Package Contents
Drive RV Antenna
w/25 ft. Cable
(311230)
13 in. Mast
Extension
Spring, Side Exit
Adapter & Antenna
Mount
Thread Lock

2
Mount Outside Antenna to a ladder
or pole, so that the entire Outside
Antenna is above the roof line of
the RV and clear of other metal
obstructions. We recommend
doing a ‘soft install’, verifying the
system works as desired, before
permanently installing the kit.
Select Mounting Location
!!!
NOTE: Keep in mind to stay below the maximum height limit allowed by law, which varies from state to state (generally 14 ft. in
western states and 13 ft.6 in. in eastern states.
common outside
antenna location

3
c
a
b
l
e
c
a
b
l
e
Once you have determined the best
location for the antenna, insert cable
through mast(s) then through Side
Exit Adpater.
cable from
antenna
Mast
Extension
13 in.
mast
13 in.
mast
run cable
through Mast
Extension(s)
Assemble the Antenna
Antenna Spring
(can be used
optionally)
Side Exit
Adapter

4
Use thread locker (provided) to thread
points and screw into place.
NOTE: Be sure the antenna is the correct
height before applying thread locker.
NOTE: When adding the side exit adapter
hold the antenna vertically and screw the
adapter from the bottom up. This reduces
cable twisting.
(Assemble the Antenna cont.)
Side Exit
Adapter
mast
mast
add thread
locker
add thread
locker
Drive OTR
Antenna
c
a
b
l
e
f
r
o
m
a
n
t
e
n
n
a

5
Mount to ladder rail on RV as shown
and route cable into RV then connect
cable to the booster. The system
performs best with maximum vertical
and horizontal separation.
NOTE: If installing with Spring, the
Side Exit Adapter must be used.
Mounting the Antenna
Side Exit
Adapter
add thread
locker
Spring
(optional)
add thread
locker
ladder rail
to booster

6
Safety Guidelines & Specifications
RF Safety Warning: Any antenna used with this device must be located at least 8 inches from all persons. AWS
Warning: The Outside Antenna must be installed no higher than 32 feet 9 inches (10 meters) above ground.
311230
698-806 806-960 1710-1880 1850-1990 1910-2170 2300-2700
SMA (F)
2.4
1.4
0.3
<2:1
> 70 > 65
2.6
2.4
0.3
3.8
3.1
0.5
3.8
2.7
0.5
3.7
2.4
0.5
4.3
2.6
0.6
7.422 x 2.688 / 188 x 68
<2:1
.40 / 0.181
Vertical
Aluminum
Alumin Plastic Type: ASA (Acrylonitrile Styrene) Acrylate)
360 360 360 360 360 360
70 78 60 70 80 33
311 / 500
50
10
Model
Frequency Band (MHz)
Connector
Peak Gain (dBi)
Gain (dBi), Typical @ 2° Elevation
Cable loss LMR-195 30 in.
Dimensions (in / mm)
VSWR
Weight (lb / kg)
Polarization
Eciency (%)
Radiator Material
Radome Material
Half-Power Azimuth Beamwidth (°)
Rated Wind Velocity (mph / kph)
Half-Power Elevation Beamwidth (°)
Impedance (Ω)
Maximum Power (W)
Mechanical Specifications
Electrical Specifications

7
DISCLAIMER: The information provided by Wilson Electronics, LLC is believed to be complete and accurate. However,
no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from its use.
MARKETING APPROVAL: Installer and end customer hereby grants to Wilson Electronics the express right to use
installers or end customers company logo in marketing, sales, financial, and public relations materials and other
communications solely to identify Customer as a Wilson Electronics customer.
2 YEAR WARRANTY
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of
purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics
shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or
replaced product back to the original consumer if located within the continental U.S.
Replacement products may include refurbished Wilson Electronics products that have been recertified to conform
with product specifications.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected to misuse,
abuse, neglect, or mishandling that alters or damages physical or electronic properties.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.

8
Notes
1.866.294.1660 www.wilsonelectronics.com [e-mail]

9
Notes
1.866.294.1660 www.wilsonelectronics.com [e-mail]

NOT AFFILIATED WITH WILSON ANTENNA
3301 East Deseret Drive, St. George, UT
866.294.1660 www.wilsonelectronics.com [e-mail]
Copyright © 2020 Wilson Electronics. All rights reserved. Wilson Electronics products covered by U.S. patent(s) and pending
application(s) For patents go to: weboost.com/us/patents
GDE000300_Rev01_08.10.20