Wilson Electronics Cellular Cradle Plus User manual
Cellular
Cradle
Plus™
Wilson
®
Electronics, Inc.
Contents:
Inside this Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Multiple Mounting Options. . . . . . . . . . . . . . . . . . . . . . . . . 1
Air Vent Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Adhesive Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Gooseneck Suction Mount . . . . . . . . . . . . . . . . . . . . . . 2
Adhesive/Screw Swivel Bracket . . . . . . . . . . . . . . . . . . . . 2
Attaching the Cradle . . . . . . . . . . . . . . . . . . . . .Back Cover
Adjusting the Cradle’s Arms . . . . . . . . . . . . . . .Back Cover
Guarantee and Warranty . . . . . . . . . . . . . . . . . .Back Cover
Note: This manual contains important safety and operating information.
Please read and follow the instructions in this manual. Failure to do
so could be hazardous and result in damage to your Signal Booster.
Disclaimer: The information provided by Wilson Electronics, Inc. is
believed to be complete and accurate. However, no responsibility is
assumed by Wilson Electronics, Inc. for any business or personal losses
arising from its use, or for any infringements of patents or other rights of third
parties that may result from its use. Copyright © 2011 Wilson Electronics,
Inc. All rights reserved.
Appearance of device and accessories may vary.
Antenna
1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Clean the area of the windshield in the location1.
you would like to attach the suction cup with an
alcohol wipe (included). Allow to dry.
Press the suction cup at the base of the mount2.
onto the windshield with even pressure. Depress
the lever above the suction cup to pump the
remaining air out of the area and to achieve a
strong suction mount.
Bend the gooseneck to the location where you3.
would like to attach the cradle. For best perfor-
mance, adjust the gooseneck so that the cradle
is allowed to rest on the dashboard.
See “Attaching the Cradle” on the back page.4.
Gooseneck Suction Mount
Adhesive Bracket
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. Peel the backing to expose the
adhesive and press the bracket
onto the desired location in the
vehicle. Note: be sure the bracket
is positioned vertically, not
horizontally.
3. Allow the adhesive to cure for 24
hours before you attach the cradle.
4. See “Attaching the Cradle”. (Note:
once the cradle is attached,
you can adjust the angle of the
adhesive bracket by applying
gentle pressure to the top or
bottom of the cradle.)
For best mounting results and long-
term performance, we suggest that
you choose a flat, smooth surface
like the console area of your vehicle
between the two front seats. If this is
not available in your vehicle, you may
mount the cradle on the front of the
dashboard.
If mounting the cradle on a sloped
area of the dashboard in your vehicle,
please note that gravity may affect
the adhesive over time. Use the
screw mount for a more permanent
attachment.
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. For an adhesive mount, peel the
backing to expose the adhesive
and press the bracket onto the
desired location in the vehicle.
(Note: the swivel feature allows the
bracket to be positioned vertically
or horizontally.) Allow the adhesive
to cure for 24 hours before you
attach the cradle.
For a screw mount, use an ice
pick or an awl to punch through
the adhesive and expose the four
screw holes in the bracket. You
must provide the screws of an
appropriate size for your particular
application. Using the bracket as a
template, mark the locations for the
screws as shown, drill pilot holes,
attach the bracket with adhesive,
and tighten all screws
3. See “Attaching the Cradle”. (Note:
Once the cradle is attached, you
can loosen the knurled wheel and
swivel the hook to the desired
angle, then re-tighten the wheel.)
1. Clean the area of the windshield
in the location you would like to
attach the suction cup. Allow to dry.
2. Press the suction cup at the base
of the mount onto the windshield
with even pressure. Depress the
lever above the suction cup to
pump the remaining air out of
the area and to achieve a strong
suction mount.
3. Bend the gooseneck to the location
where you would like to attach
the cradle. For best performance,
adjust the gooseneck so that the
cradle is allowed to rest on the
dashboard.
4. See “Attaching the Cradle”.
NOTE: State law prohibits drivers in
some states from using suction mounts
on their windshields when operating
motor vehicles. In such cases, other
Wilson Electronics dashboard or
console mounting options should
be used. Wilson does not take any
responsibility for any fines, penalties,
or damages that may be incurred as a
result of disregarding this notice.
Attaching The Cradle
Once you have installed your selected mount in the desired location, attach the
cradle by aligning the rectangular hole on its back with the hook on the mount.
Grasping the sides of the cradle, slide it downward approximately ¼ inch into place.
Adhesive/Screw
Swivel Bracket
Gooseneck Suction
Bracket (available on some kits)
Quick Release
Button
Adjustable Arms
Adjustable Feet
Placing Your Phone in the Cradle
1. Press the quick-release button on the lower right side to open the cradle arms
wide enough to accommodate your phone.
2. With the phone resting against the back of the cradle, gently squeeze the cradle
arms together to hold the phone in place. Note that the arms move up and down
and have upper and lower sections.
3. Adjust the two feet at the bottom of the cradle to support the phone at its base.
4. Connect your hands-free device to the phone, adjusting the cradle arms or feet as
necessary. For the Cradle Plus, connect the antenna cable to the Wilson amplifier
in accordance with the instructions supplied with the amplifier.
5. To remove the phone, press the quick-release button to open the cradle arms and
release the phone.
If you have any questions regarding the installation
or operation of your Wilson Cell Phone Cradle
or Cell Phone Cradle Plus, please contact our
Technical Support Department at 866-294-1660, or
3301 East Deseret Drive, St. George, Utah 84790
800.204.4104 • 435.673.5021
www.wilsonelectronics.com
Improving Your Cellular Signal
Part # 104080 AIG Cradle -rev.02- 07.07.10
Hours 7am to 6 pm MST
1. Insert the two vent clips into the
circular hole in the bracket and
slide them to each end of the slot.
The flat surface of the clips should
face upward.
2. Slide the bracket clips into the
chosen vent location until they
snap into place. If necessary, use
a thin-bladed screwdriver to gently
pry the clips apart as they slide into
the vent.
3. Position the moveable arm at the
base of the bracket to achieve
the desired angle and to provide
additional stability for the bracket.
4. See “Attaching the Cradle”.
Air Vent Bracket
Note: State law prohibits drivers in
some states from using suction mounts
on their windshields when operating
motor vehicles. In such cases, other
Wilson Electronics dashboard or con-
sole mounting options should be used.
Wilson Electronics does not take any
responsibility for any fi nes, penalties,
or damages that may be incurred as a
result of disregarding this notice.
Adhesive Bracket
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. Peel the backing to expose the
adhesive and press the bracket
onto the desired location in the
vehicle. Note: be sure the bracket
is positioned vertically, not
horizontally.
3. Allow the adhesive to cure for 24
hours before you attach the cradle.
4. See “Attaching the Cradle”. (Note:
once the cradle is attached,
you can adjust the angle of the
adhesive bracket by applying
gentle pressure to the top or
bottom of the cradle.)
For best mounting results and long-
term performance, we suggest that
you choose a flat, smooth surface
like the console area of your vehicle
between the two front seats. If this is
not available in your vehicle, you may
mount the cradle on the front of the
dashboard.
If mounting the cradle on a sloped
area of the dashboard in your vehicle,
please note that gravity may affect
the adhesive over time. Use the
screw mount for a more permanent
attachment.
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. For an adhesive mount, peel the
backing to expose the adhesive
and press the bracket onto the
desired location in the vehicle.
(Note: the swivel feature allows the
bracket to be positioned vertically
or horizontally.) Allow the adhesive
to cure for 24 hours before you
attach the cradle.
For a screw mount, use an ice
pick or an awl to punch through
the adhesive and expose the four
screw holes in the bracket. You
must provide the screws of an
appropriate size for your particular
application. Using the bracket as a
template, mark the locations for the
screws as shown, drill pilot holes,
attach the bracket with adhesive,
and tighten all screws
3. See “Attaching the Cradle”. (Note:
Once the cradle is attached, you
can loosen the knurled wheel and
swivel the hook to the desired
angle, then re-tighten the wheel.)
1. Clean the area of the windshield
in the location you would like to
attach the suction cup. Allow to dry.
2. Press the suction cup at the base
of the mount onto the windshield
with even pressure. Depress the
lever above the suction cup to
pump the remaining air out of
the area and to achieve a strong
suction mount.
3. Bend the gooseneck to the location
where you would like to attach
the cradle. For best performance,
adjust the gooseneck so that the
cradle is allowed to rest on the
dashboard.
4. See “Attaching the Cradle”.
NOTE: State law prohibits drivers in
some states from using suction mounts
on their windshields when operating
motor vehicles. In such cases, other
Wilson Electronics dashboard or
console mounting options should
be used. Wilson does not take any
responsibility for any fines, penalties,
or damages that may be incurred as a
result of disregarding this notice.
Attaching The Cradle
Once you have installed your selected mount in the desired location, attach the
cradle by aligning the rectangular hole on its back with the hook on the mount.
Grasping the sides of the cradle, slide it downward approximately ¼ inch into place.
Adhesive/Screw
Swivel Bracket
Gooseneck Suction
Bracket (available on some kits)
Quick Release
Button
Adjustable Arms
Adjustable Feet
Placing Your Phone in the Cradle
1. Press the quick-release button on the lower right side to open the cradle arms
wide enough to accommodate your phone.
2. With the phone resting against the back of the cradle, gently squeeze the cradle
arms together to hold the phone in place. Note that the arms move up and down
and have upper and lower sections.
3. Adjust the two feet at the bottom of the cradle to support the phone at its base.
4. Connect your hands-free device to the phone, adjusting the cradle arms or feet as
necessary. For the Cradle Plus, connect the antenna cable to the Wilson amplifier
in accordance with the instructions supplied with the amplifier.
5. To remove the phone, press the quick-release button to open the cradle arms and
release the phone.
If you have any questions regarding the installation
or operation of your Wilson Cell Phone Cradle
or Cell Phone Cradle Plus, please contact our
Technical Support Department at 866-294-1660, or
3301 East Deseret Drive, St. George, Utah 84790
800.204.4104 • 435.673.5021
www.wilsonelectronics.com
Improving Your Cellular Signal
Part # 104080 AIG Cradle -rev.02- 07.07.10
Hours 7am to 6 pm MST
1. Insert the two vent clips into the
circular hole in the bracket and
slide them to each end of the slot.
The flat surface of the clips should
face upward.
2. Slide the bracket clips into the
chosen vent location until they
snap into place. If necessary, use
a thin-bladed screwdriver to gently
pry the clips apart as they slide into
the vent.
3. Position the moveable arm at the
base of the bracket to achieve
the desired angle and to provide
additional stability for the bracket.
4. See “Attaching the Cradle”.
Air Vent Bracket
For best mounting results and long-term performance,
we suggest that you choose a flat, smooth surface like
the console area of your vehicle between the two front
seats. If this is not available in your vehicle, you may
mount the cradle on the front of the dashboard.
If mounting the cradle on a sloped area of the dash-
board in your vehicle, please note that gravity may
affect the adhesive over time. Use the screw mount for
a more permanent attachment.
Clean the area where the bracket is to be mounted with an alcohol wipe (included).1.
Allow to dry.
2. For an adhesive mount, peel the backing to expose the adhesive and press the
bracket onto the desired location in the vehicle. Note: The swivel feature allows the
bracket to be positioned vertically or horizontally. Allow the adhesive to cure for 24
hours before you attach the cradle.
For a screw mount, use an ice pick or an awl to punch through the adhesive and
expose the four screw holes in the bracket. You must provide the screws of an ap-
propriate size for your particular application. Using the bracket as a template, mark the
locations for the screws, drill holes, attach the bracket with adhesive, and tighten all
screws.
See “Attaching the Cradle” on the back page.3. Note: Once the cradle is attached, you
can loosen the knurled wheel and swivel the hook to the desired angle, then re-tighten
the wheel.
Adhesive/Screw Swivel Bracket
Allow the adhesive to cure for 24 hours before you attach the cradle.3.
See “Attaching Cradle” on the back page.4. Note: Once the cradle is attached, you can
adjust the angle of the adhesive bracket by applying gentle pressure to the top or
bottom of the cradle.
Installation Instructions for the Following Wilson Electronics Antenna
Cellular Cradle Plus™
Inside this Package
Cellular Cradle Plus™
Wilson Electronics’ Cellular Cradle Plus offers a built-in cell phone signal antenna/coupler.
Used in conjunction with one of Wilson Electronics Cellular Signal Boosters, the Cradle
Plus can improve your cellular signal more than 20 times and help you stay connected in
places you never could before!
Multiple Mounting Options
Multiple mounting options allow for a custom installation in virtually any vehicle. Before
mounting, determine the desired location of the cradle in your vehicle. Hold the cradle in the
intended position and be sure it does not obstruct your view or block access to any controls
or gauges necessary for safe driving.
Slide the bracket clips into the chosen vent1.
location until they snap into place. If necessary,
use a thin-bladed screwdriver to gently pry the
clips apart as they slide into the vent.
Position the moveable arm at the base of the2.
bracket to achieve the desired angle and to
provide additional stability for the bracket.
See “Attaching the Cradle” on the back page.3.
Air Vent Bracket
Adhesive Bracket
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. Peel the backing to expose the
adhesive and press the bracket
onto the desired location in the
vehicle. Note: be sure the bracket
is positioned vertically, not
horizontally.
3. Allow the adhesive to cure for 24
hours before you attach the cradle.
4. See “Attaching the Cradle”. (Note:
once the cradle is attached,
you can adjust the angle of the
adhesive bracket by applying
gentle pressure to the top or
bottom of the cradle.)
For best mounting results and long-
term performance, we suggest that
you choose a flat, smooth surface
like the console area of your vehicle
between the two front seats. If this is
not available in your vehicle, you may
mount the cradle on the front of the
dashboard.
If mounting the cradle on a sloped
area of the dashboard in your vehicle,
please note that gravity may affect
the adhesive over time. Use the
screw mount for a more permanent
attachment.
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. For an adhesive mount, peel the
backing to expose the adhesive
and press the bracket onto the
desired location in the vehicle.
(Note: the swivel feature allows the
bracket to be positioned vertically
or horizontally.) Allow the adhesive
to cure for 24 hours before you
attach the cradle.
For a screw mount, use an ice
pick or an awl to punch through
the adhesive and expose the four
screw holes in the bracket. You
must provide the screws of an
appropriate size for your particular
application. Using the bracket as a
template, mark the locations for the
screws as shown, drill pilot holes,
attach the bracket with adhesive,
and tighten all screws
3. See “Attaching the Cradle”. (Note:
Once the cradle is attached, you
can loosen the knurled wheel and
swivel the hook to the desired
angle, then re-tighten the wheel.)
1. Clean the area of the windshield
in the location you would like to
attach the suction cup. Allow to dry.
2. Press the suction cup at the base
of the mount onto the windshield
with even pressure. Depress the
lever above the suction cup to
pump the remaining air out of
the area and to achieve a strong
suction mount.
3. Bend the gooseneck to the location
where you would like to attach
the cradle. For best performance,
adjust the gooseneck so that the
cradle is allowed to rest on the
dashboard.
4. See “Attaching the Cradle”.
NOTE: State law prohibits drivers in
some states from using suction mounts
on their windshields when operating
motor vehicles. In such cases, other
Wilson Electronics dashboard or
console mounting options should
be used. Wilson does not take any
responsibility for any fines, penalties,
or damages that may be incurred as a
result of disregarding this notice.
Attaching The Cradle
Once you have installed your selected mount in the desired location, attach the
cradle by aligning the rectangular hole on its back with the hook on the mount.
Grasping the sides of the cradle, slide it downward approximately ¼ inch into place.
Adhesive/Screw
Swivel Bracket
Gooseneck Suction
Bracket (available on some kits)
Quick Release
Button
Adjustable Arms
Adjustable Feet
Placing Your Phone in the Cradle
1. Press the quick-release button on the lower right side to open the cradle arms
wide enough to accommodate your phone.
2. With the phone resting against the back of the cradle, gently squeeze the cradle
arms together to hold the phone in place. Note that the arms move up and down
and have upper and lower sections.
3. Adjust the two feet at the bottom of the cradle to support the phone at its base.
4. Connect your hands-free device to the phone, adjusting the cradle arms or feet as
necessary. For the Cradle Plus, connect the antenna cable to the Wilson amplifier
in accordance with the instructions supplied with the amplifier.
5. To remove the phone, press the quick-release button to open the cradle arms and
release the phone.
If you have any questions regarding the installation
or operation of your Wilson Cell Phone Cradle
or Cell Phone Cradle Plus, please contact our
Technical Support Department at 866-294-1660, or
3301 East Deseret Drive, St. George, Utah 84790
800.204.4104 • 435.673.5021
www.wilsonelectronics.com
Improving Your Cellular Signal
Part # 104080 AIG Cradle -rev.02- 07.07.10
Hours 7am to 6 pm MST
1. Insert the two vent clips into the
circular hole in the bracket and
slide them to each end of the slot.
The flat surface of the clips should
face upward.
2. Slide the bracket clips into the
chosen vent location until they
snap into place. If necessary, use
a thin-bladed screwdriver to gently
pry the clips apart as they slide into
the vent.
3. Position the moveable arm at the
base of the bracket to achieve
the desired angle and to provide
additional stability for the bracket.
4. See “Attaching the Cradle”.
Air Vent Bracket
Clean the area where the bracket is to be1.
mounted with an alcohol wipe (included).
Allow to dry.
Peel the backing to expose the adhesive and2.
press the bracket onto the desired location
in the vehicle. Note: Be sure the bracket is
positioned vertically, not horizontally.
Adhesive Bracket
Adhesive Bracket
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. Peel the backing to expose the
adhesive and press the bracket
onto the desired location in the
vehicle. Note: be sure the bracket
is positioned vertically, not
horizontally.
3. Allow the adhesive to cure for 24
hours before you attach the cradle.
4. See “Attaching the Cradle”. (Note:
once the cradle is attached,
you can adjust the angle of the
adhesive bracket by applying
gentle pressure to the top or
bottom of the cradle.)
For best mounting results and long-
term performance, we suggest that
you choose a flat, smooth surface
like the console area of your vehicle
between the two front seats. If this is
not available in your vehicle, you may
mount the cradle on the front of the
dashboard.
If mounting the cradle on a sloped
area of the dashboard in your vehicle,
please note that gravity may affect
the adhesive over time. Use the
screw mount for a more permanent
attachment.
1. Clean the area where the bracket
is to be mounted with rubbing
alcohol and a soft cloth. Allow to
dry.
2. For an adhesive mount, peel the
backing to expose the adhesive
and press the bracket onto the
desired location in the vehicle.
(Note: the swivel feature allows the
bracket to be positioned vertically
or horizontally.) Allow the adhesive
to cure for 24 hours before you
attach the cradle.
For a screw mount, use an ice
pick or an awl to punch through
the adhesive and expose the four
screw holes in the bracket. You
must provide the screws of an
appropriate size for your particular
application. Using the bracket as a
template, mark the locations for the
screws as shown, drill pilot holes,
attach the bracket with adhesive,
and tighten all screws
3. See “Attaching the Cradle”. (Note:
Once the cradle is attached, you
can loosen the knurled wheel and
swivel the hook to the desired
angle, then re-tighten the wheel.)
1. Clean the area of the windshield
in the location you would like to
attach the suction cup. Allow to dry.
2. Press the suction cup at the base
of the mount onto the windshield
with even pressure. Depress the
lever above the suction cup to
pump the remaining air out of
the area and to achieve a strong
suction mount.
3. Bend the gooseneck to the location
where you would like to attach
the cradle. For best performance,
adjust the gooseneck so that the
cradle is allowed to rest on the
dashboard.
4. See “Attaching the Cradle”.
NOTE: State law prohibits drivers in
some states from using suction mounts
on their windshields when operating
motor vehicles. In such cases, other
Wilson Electronics dashboard or
console mounting options should
be used. Wilson does not take any
responsibility for any fines, penalties,
or damages that may be incurred as a
result of disregarding this notice.
Attaching The Cradle
Once you have installed your selected mount in the desired location, attach the
cradle by aligning the rectangular hole on its back with the hook on the mount.
Grasping the sides of the cradle, slide it downward approximately ¼ inch into place.
Adhesive/Screw
Swivel Bracket
Gooseneck Suction
Bracket (available on some kits)
Quick Release
Button
Adjustable Arms
Adjustable Feet
Placing Your Phone in the Cradle
1. Press the quick-release button on the lower right side to open the cradle arms
wide enough to accommodate your phone.
2. With the phone resting against the back of the cradle, gently squeeze the cradle
arms together to hold the phone in place. Note that the arms move up and down
and have upper and lower sections.
3. Adjust the two feet at the bottom of the cradle to support the phone at its base.
4. Connect your hands-free device to the phone, adjusting the cradle arms or feet as
necessary. For the Cradle Plus, connect the antenna cable to the Wilson amplifier
in accordance with the instructions supplied with the amplifier.
5. To remove the phone, press the quick-release button to open the cradle arms and
release the phone.
If you have any questions regarding the installation
or operation of your Wilson Cell Phone Cradle
or Cell Phone Cradle Plus, please contact our
Technical Support Department at 866-294-1660, or
3301 East Deseret Drive, St. George, Utah 84790
800.204.4104 • 435.673.5021
www.wilsonelectronics.com
Improving Your Cellular Signal
Part # 104080 AIG Cradle -rev.02- 07.07.10
Hours 7am to 6 pm MST
1. Insert the two vent clips into the
circular hole in the bracket and
slide them to each end of the slot.
The flat surface of the clips should
face upward.
2. Slide the bracket clips into the
chosen vent location until they
snap into place. If necessary, use
a thin-bladed screwdriver to gently
pry the clips apart as they slide into
the vent.
3. Position the moveable arm at the
base of the bracket to achieve
the desired angle and to provide
additional stability for the bracket.
4. See “Attaching the Cradle”.
Air Vent Bracket
Included in the 301146 Kit Only
Adhesive Bracket
Adhesive/Screw
Swivel Bracket
Adapter
(For use with your MobilePro)
(359909)
Plug one end into the Cradle Plus
Antenna, and the other end into your
MobilePro (sold separately).
Cellular
Cradle Plus™
3 Sets of arms
(1 set small, 1
set medium, 1
set large)
Adhesive Bracket
Air Vent
Bracket
Cellular
Gooseneck Suction
Cup Mount
(For mounting the cradle
to the windshield)
(901120)
Appearance of device and accessories may vary.
Attaching the Cradle
Once you have installed your selected mount in the desired location, attach the cradle by
aligning the rectangular hole on its back with the hook on the mount. Grasping the sides of
the cradle, slide it downward approximately 1/4 inch into place.
103071_Rev03_10.17.11
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If
for any reason the performance of any product is not acceptable, simply return the product directly to the
reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics Antennas are warranted for one (1) year against defects in workmanship and/or
materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated
proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense, with a dated
proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics.
Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for
delivery of the repaired or replaced product back to the original consumer if located within the continental
U.S.
This warranty does not apply to any antennas determined by Wilson Electronics to have been subjected
to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Adjusting the Cradle’s Arms
Included with your Cradle are various sized arms, which will provide you with multiple
options to customize the Cradle to fit your phone.
1. Change arms
Gently grab the arm
and lift upward until
the arm slides free
from the Cradle.
2. Reposition arms
Position the arm above a different slot on the Cradle (indicated
by the arrows in the drawing). Gently slide the arm down until
the arm is firmly in place.
NOTE: The cell phone must be placed in the Cradle to work
properly. Use a Bluetooth or wired hands free device.
Slots Slots
Other Wilson Electronics Antenna manuals
Wilson Electronics
Wilson Electronics 304411 User manual
Wilson Electronics
Wilson Electronics 301130 User manual
Wilson Electronics
Wilson Electronics 301133 User manual
Wilson Electronics
Wilson Electronics 304411 User manual
Wilson Electronics
Wilson Electronics 301102 User manual
Wilson Electronics
Wilson Electronics 301111 User manual
Wilson Electronics
Wilson Electronics 301130 User manual
Wilson Electronics
Wilson Electronics 301208 User manual
Wilson Electronics
Wilson Electronics 301208 User manual
Wilson Electronics
Wilson Electronics 301124 User manual
Wilson Electronics
Wilson Electronics WR-500 User manual
Wilson Electronics
Wilson Electronics 301133 User manual
Wilson Electronics
Wilson Electronics 301104 User manual
Wilson Electronics
Wilson Electronics 301102 User manual
Wilson Electronics
Wilson Electronics 301121 User manual
Wilson Electronics
Wilson Electronics 301135 User manual
Wilson Electronics
Wilson Electronics 301134 User manual
Wilson Electronics
Wilson Electronics 301201 User manual
Wilson Electronics
Wilson Electronics 301143 User manual
Wilson Electronics
Wilson Electronics 304451 User manual
Popular Antenna manuals by other brands
Winegard
Winegard YA7000C instruction manual
Ventev
Ventev M6060060P1D43602V manual
Somogyi Elektronic
Somogyi Elektronic home FZ3 instruction manual
Optex
Optex iVision+ Connect IVPC-ANT Settings and setup guide
Superior Antenna Manufacturing
Superior Antenna Manufacturing SM12 installation manual
Altelix
Altelix AY09G12M2-PRO Assembly instructions
