Wilson Electronics 4G Low-Profile Dome Antenna User manual

User Manual
Ultrathin Radome Antenna
4G Low-Profile
Dome Antenna
NEED HELP? support.weboost.com 866.294.1660

______
Index
Package Contents 1
Assembly Diagram: With Ceiling Mount 2
Assembly Diagram: Without Ceiling Mount 3
Installation: Ceiling Mount 4
Installation: Without Ceiling Mount 7
Specifications 9
Warranty Back

4G LOW-PROFILE DOME ANTENNA 1
________
Package
Contents
Low-Profile
Dome Antenna
Reflector Collar Nut Ceiling Mount
& Tab Ring
for hard ceiling
mounting

24G LOW-PROFILE DOME ANTENNA
______
Assembly Diagram: With
Ceiling Mount
n-female connector
to booster
Plastic Nut
Tab Ring
ceiling mount
drill or cut 3. in. / 76.2
mm dia. hole with two .50
inch diameter tab cutouts
180°opposed
drywall / plaster board
Low-Profile Dome Antenna

4G LOW-PROFILE DOME ANTENNA 3
______
Assembly Diagram: With
Reflector
reflector
n-female connector
to booster
plastic nut
plastic collar
drill or cut
2.5 in. / 64 mm dia. hole
drywall / plaster board
low-profile dome antenna

44G LOW-PROFILE DOME ANTENNA
______
Installation: Ceiling Mount
clamps will swing
out while tightening
3.0 - 3.1 in.
Ø .50 in.
ceiling
ceiling
clamps will swing
out while tightening
3.0 - 3.1 in.
Ø .50 in.
ceiling
ceiling
This insert is used to allow low-profile dome antennas to be
installed when there is no access to the area above the ceiling (like
drywall or plaster board) other than a hole to fish the wire through.
Drill or cut a hole 3.0-3.1 in. (76.2-
78.74 mm) in drywall with two 0.5
in. (12.7 mm) diameter tab cutouts
180° opposed.
Swing the two clamps on the
ceiling collar toward the inside.
NOTE: The clamps are limited in
how far they can swing in one
direction due to the side wall of
the sleeve. Swing other direction.
1
2

4G LOW-PROFILE DOME ANTENNA 5
clamps will swing
out while tightening
3.0 - 3.1 in.
Ø .50 in.
ceiling
ceiling
clamps will swing
out while tightening
3.0 - 3.1 in.
Ø .50 in.
ceiling
ceiling
Insert mounting sleeve into the
hole of drywall and tighten. The
clamps will swing out and brace
the ceiling collar against the
drywall while tightening.
Mount tab ring onto antenna and
tighten nut firmly.
NOTE: Do not over tighten.
NOTE: The Collar is not used with
Ceiling Mount.
NOTE: The text “THIS SIDE UP”
on the tab ring for the assembly
direction.
______
(Installation: Ceiling Mount cont.)
4
3
tab ring
nut
from antenna
from booster
slots
tabs
ceiling

64G LOW-PROFILE DOME ANTENNA
Connect antenna cable to
booster cable.
Align tab ring tabs with slots in
ceiling mount and insert antenna.
Twist antenna clockwise 1/8th of
a turn to lock in place. Antenna
is now fixed in place.
NOTE: Antenna can be removed
from ceiling mount without
damage. Simply rotate back
1/8 turn.
______
(Installation: Ceiling Mount cont.)
5
6
tab ring
nut
from antenna
from booster
slots
tabs
ceiling
tab ring
nut
from antenna
from booster
slots
tabs
ceiling

4G LOW-PROFILE DOME ANTENNA 7
______
Installation: Without Ceiling
Mount
This option is used if attic access is available, in which the reflector
can be used to increase performance.
Drill or cut a hole 2.5-2.75 in. (64-
70mm) in center of ceiling tile or
at desired location.
Slide the antenna/assembly
through the hole. Slide the collar
and nut onto the cable. Turn
the nut, tightening the antenna
against the ceiling.
NOTE: Fiberboard ceiling tile is
soft; tighten the nut just enough
to hold the antenna firmly
in place.
NOTE: For optimum performance,
metal ceiling rails need to be a
minimum 7.875 in. (200mm) from
the antenna center.
1
2
2.5 - 2.75 in.
ceiling
nut
collar
reflector
attic space
attic space
2.5 - 2.75 in.
ceiling
nut
collar
reflector
attic space
attic space

84G LOW-PROFILE DOME ANTENNA
Thread the reflector onto the
antenna stem.
______
(Installation: Without Ceiling Mount cont.)
3
2.5 - 2.75 in.
ceiling
nut
collar
reflector
attic space
attic space
Connect antenna cable to
booster cable.
4
tab ring
nut
from antenna
from booster
slots
tabs
ceiling

4G LOW-PROFILE DOME ANTENNA 9
Frequency Band
(MHz)
608-960 / 1695-2200 /
2300-2700
Nominal Impedance 50
VSWR
(698-960 MHz) 2:1
VSWR
(1695-2200 MHz) 2:1
Average Peak Gain
(608-960 MHz) 7 dBi
Average Peak Gain
(1695-2200 MHz) 7 dBi
Average Peak Gain
(2300-2700 MHz) 5 dBi
Efciency
(608-960 MHz) 70%
Efciency
(1695-2200 MHz) 65%
Efciency
(2300-2700 MHz) 60%
Horizontal Plane
(th=45deg) Omni
HPBW Vertical Plane
(608-960 MHz) 90° Typ
HPBW Vertical Plane
(1695-2200 MHz) 25° Typ
HPBW Vertical Plane
(2300-2700 MHz) 25° Typ
Maximum Power Input 40 W
Cable Type Diameter 0.16 in. Low Loss,
Plenum Rated
Cable Length 10 in. / 254mm
Connector Type N-Female
Frequency Band
(MHz)
608-960 / 1695-2200 /
2300-2700
Nominal Impedance 50
VSWR
(698-960 MHz) 2:1
VSWR
(1695-2200 MHz) 2:1
Average Peak Gain
(608-960 MHz) 4 dBi
Average Peak Gain
(1695-2200 MHz) 6 dBi
Average Peak Gain
(2300-2700 MHz) 6 dBi
Efciency
(608-960 MHz) 70%
Efciency
(1695-2200 MHz) 65%
Efciency
(2300-2700 MHz) 60%
Horizontal Plane
(th=45deg) Omni
HPBW Vertical Plane
(608-960 MHz) 100° Typ
HPBW Vertical Plane
(1695-2200 MHz) 130° Typ
HPBW Vertical Plane
(2300-2700 MHz) 130° Typ
Maximum Power Input 40 W
Cable Type Diameter 0.16 in. Low Loss,
Plenum Rated
Cable Length 10 in. / 254mm
Connector Type N-Female
NEED HELP? support.weboost.com 866.294.1660
______
Specifications
ANTENNA ELECTRICAL SPEC. WITH REFLECTOR ANTENNA ELECTRICAL SPEC. WITHOUT REFLECTOR

3301 East Deseret Drive, St. George, UT
866.294.1660 www.weboost.com support.weboost.com
Copyright © 2017 Wilson Electronics. All rights reserved.
Wilson Electronics products covered by U.S. patent(s) and pending application(s)
For patents go to: weboost.com/us/patents
NOT AFFILIATED WITH WILSON ANTENNA GDE000030_Rev01_11-02-17
2 YEAR WARRANTY
Wilson Electronics Signal Boosters are warranted for two (2) years against defects in
workmanship and/or materials. Warranty cases may be resolved by returning the product
directly to the reseller with a dated proof of purchase.
Antennas may also be returned directly to the manufacturer at the consumer’s expense,
with a dated proof of purchase and a Returned Material Authorization (RMA) number
supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair or
replace the product. Wilson Electronics will pay for delivery of the repaired or replaced
product back to the original consumer if located within the continental U.S.
Replacement products may include refurbished Wilson Electronicst products that have
been recertified to conform with product specifications.
This warranty does not apply to any antennas determined by Wilson Electronics to have
been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical
or electronic properties.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.
DISCLAIMER: The information provided by Wilson Electronics is believed to be complete and accurate.
However, no responsibility is assumed by Wilson Electronics for any business or personal losses arising
from its use, or for any infringements of patents or other rights of third parties that may result from its use.