WilTec 62283 User manual

Operation Manual
WALLPAPER STRIPPER
ARTICLE NUMBER: 62283
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
by WilTec Wildanger Technik GmbH Seite 8
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

The information contained in this document is subject to change without prior notice. o part of this
document can be copied or duplicated in another form without the prior written consent of WilTec
Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in
this user manual or the connection diagram.
Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual
is complete, accurate and updated, errors cannot always be avoided. In the event of problems with
this user manual please complete and send this form back to us.
FAX-notification (+++49 2403 55592-15),
from: ________________________________________
Name: ________________
Firm:_____________________
Tel/Fax:__________________
I would like to report the following mistakes:
_______________________________ ____________________________________
Customer Service WilTec Wildanger Technik GmbH
e-mail: [email protected]
Tel:++ [phone]
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury by means of fire or
electric shock we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you have understood its
content.
Always use a grounded power connection with the appropriate mains voltage. You can
nd the corresponding mains voltage on the type plate. If you have any doubts about the
connection being grounded, have it checked by a qualied professional. Never use a
faulty electric cable.
o not inspect the electrical part of the pressure pond lter in a wet or damp
environment or when you are wet yourself and protect it from direct sunlight. Install this
device in a safe location so that nobody can step on the cable, fall over or damage it.
isconnect the power plug before cleaning it and use only a damp cloth for cleaning.
Avoid using cleaning agents and make sure that no liquid enters the electrical part of the pump.
The electric part of the device contains no parts that can be inspected or serviced by the user. Leave
the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised
intervention the 2-year warranty is no longer valid! Keep these operation instructions safe.
by WilTec Wildanger Technik GmbH Seite 9
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Features
Power supply: 240 V ~ 50 Hz
Wattage: 2200 W
Tank capacity: 4.5 litres
Hose length: 3 m (flexible hose)
Safety class: IPX4
et weight: approx. 2.4 kg
Origin: China
Description
1. Water tank
2. Screw cap
3. Hose
4. Applicator
5. Power cord
6. Connector
7. Valve
by WilTec Wildanger Technik GmbH Seite 10
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Security Instructions
Attention: The use of this product entails the risk of severe scalding due to the high temperatures of
the emitted vapour (approx. 100°C). You should therefore make sure to understand and follow the se-
curity instructions below in order to minimise the risk of accidents. Infringement may lead to severe in-
juries as well as damage to the device and its surroundings.
Always make sure to wear work gloves when utilising the device and make sure to use further
protective clothing (protective goggles, respiratory mask etc.) if necessary in order to further
minimise the risk of injury.
ever direct the applicator at people, animals or temperature-sensitive items.
Do not place heavy objects on top of the device and make sure that the hose is neither stuck
nor knotted in any way.
Be aware that the hot vapour is capable of heating materials in the vicinity and coming into
contact with them might cause injuries.
Always make sure to unplug the device before performing cleaning or maintenance work and
when it is not in use.
Always ensure that the device is placed on a solid and secure surface from which it cannot fall
down.
Do not use the device, if the water level is below the minimum filling capacity mark.
Do not hold, pull or carry the device at the cable or hose and make sure that both are kept
away from heat sources as well as sharp edges.
Do not use the device in case the cable has been damaged and never try to repair broken or
damaged cables. In case of a damaged cable, always make sure to replace them before the
device can be used again.
Before working with the wallpaper stripper, make sure to mask wall sockets and light switches
properly and be careful not to steam while working as this might lead to short circuits.
Always make sure to keep your work space tidy and well-lit as cluttered and dark work places
significantly increase the risk of accidents.
Do not overestimate yourself, do not take any risks and always make sure to remain in a sta-
ble position with secure footing.
Do not get distracted while using the device and do not utilise it, if you are tired or under the
influence of alcohol, drugs or medication.
 Always let the device cool down for 30 minutes after using it and make sure to store it in a dry
place without any heat sources or highly flammable and explosive items.
either use the device in the vicinity of highly flammable and explosive materials, nor in rooms
without proper ventilation.
Protect yourself from electric discharge by avoiding contact with metallic or electric objects.
Do not leave the device unattended and always make sure to keep it out of reach of children
and animals.
Keep bystanders away from your work space as they might distract you and thereby increase
the risk of accidents.
This product was manufactured for DIY purposes and is therefore not suited for industrial or
commercial use and requires breaks in between longer periods of usage as it might otherwise
suffer damage from excessive stress.
Do not dismantle the device. Repairs should only be performed by specifically trained person-
nel.
Always free the device from remains of wallpapers as well as other residue after usage. Make
thereby sure to wait for the device to cool down until it is no longer a risk of injury before be-
ginning the check.
by WilTec Wildanger Technik GmbH Seite 11
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

In order to guarantee the functionality of the device make sure to check it for visible damage
and signs of material fatigue before using it. Further ensure that all parts have been assem-
bled correctly and in a secure manner.
Attention! Only utilise accessories that have been produced or authorised by the manufacturer
as the use of lower quality parts might lead to injuries as well as damage to the device and its
surroundings.
Setup
1. Make sure that the device is not connected to the mains supply.
2. Remove the screw cap (2) and fill fresh, addition free water into the tank (1). [Fig. A]
3. Properly reattach the screw cap (2). Please be aware that the screw cap is equipped with a
valve (7) capable of releasing excessive pressure [Fig. C]. In case of this part being damaged,
the device's functionality can only be guaranteed, if an original spare part is used to replace it.
4. Connect the device's power cord (5) with the connector (6) as well as a secure wall outlet that
not located in the direct vicinity of the wall you want to work on. [Fig. B]
5. ow wait for the water to be heated before you start working. We advise to place the applica-
tor inside a bucket until it is ready. It approximately takes 15 minutes for the to reach its ser-
vice temperature.
Application
The device is ready for use once the unpressurised vapour is released from the applicator (4).
ow incise the wallpaper before then slowly guiding the applicator (4) over the same in order
to steam it.
Pay attention to the condition of the wall and the wallpaper in order to optimise the efficiency
of your work. (Thicker wallpapers might require you to wait 10-20 minutes before they can be
removed)
Make sure to regularly check the water level.
In case of the tank requiring to be refilled, make sure to disconnect the plug and wait 2 min -
utes before then opening the screw cap (2).
by WilTec Wildanger Technik GmbH Seite 12
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Machine capacity
(W)
Cable length (m) Correspondent
< 15 < 25 < 50 Amperage / area2
Admissible conduction current (A)
750 6 6 6 6A – 0.75 mm²
1100 6 6 6 10A – 1.00 mm²
1600 10 10 15 15A – 1.50 mm²
2700 15 15 20 20A – 2.50 mm²
Maintenance
This product does not require any specific maintenance procedures and only has to be freed from re-
mains of wallpapers as well as other residue after having been used. Only clean the device's plastic
parts using a soft and damp piece of fabric. Do not submerge the device in water or other liquids and
do not use chemical cleaning agents or oils.
Attention: Maintenance of the electric parts of the wallpaper stripper should only be performed by
specifically trained personnel.
by WilTec Wildanger Technik GmbH Seite 13
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were
implemented in the law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.
The company WilTec Technik GmbH has been registrated in the German registry EAR under the
WEEE-registration number DE45283704.
Disposal of used electrical and electronic appliances
(intended for use in the countries of the European
Union and other European countries with a separate
collection system for these appliances).
The logo on the article or on its packaging points out
that this article must not be treated as normal
household waste but must be disposed to a recycling
collection point for electronic and electrical waste
equipment. By contributing to the correct disposal of
this article you protect the environment and the health
of your fellow men. Environment and health are
threatened by inappropriate disposal.
Materials’ recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal
waste disposal facilities or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions
manual require the written permission of WilTec Wildanger Technik GmbH.
by WilTec Wildanger Technik GmbH Seite 14
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de