Winco 3400 Reference guide

Page 1 of 4
006245 Rev K Date 06-26-13 JWC
3400 & 3409
Wall Mounted, Telescopic Screen
CUSTOMER INSTRUCTIONS
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone],
e-mail: [email protected] before attempting to use this product; otherwise injury may occur.
Winco assumes no responsibility for damage or injury caused by the
improper assembly, installation or use of these products.
1. READ AND FOLLOW ALL DIRECTIONS. 2. NEVER hang equipment or personal objects from Curtain Rod;
Screen could fall and INJURY MAY OCCUR.
3. NEVER place screen near open flame or over a radiator or heat register.
4. NEVER place screen in front of a door or exit sign; In case of emergency screen could block or hinder
evacuation.
5. SUFFOCATION DANGER to children; Screen could block nose and mouth and prevent breathing.
VINYL SCREEN IS NOT A TOY.
6. DO NOT allow children to play with, or climb on screen; Screen could fall and SERIOUS INJURY MAY
OCCUR.
7. Periodically, recheck tightness of mounting screws.
8. ALWAYS mount at least two mounting screws to a wall stud, “dead wood” or other solid wall structure;
DO NOT attach to drywall; Professional installation is recommended.
9. DO NOT use screen in or with ANY type of vehicle or trailer.
10. Immediately remove from service; Any screen with broken or missing parts, torn vinyl, or other visible
damage.
11. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
12. SAVE THESE INSTRUCTIONS for future reference and training.
Tools needed:
•Phillips-Head Screwdriver
•Scissors or box cutter
•Special tools for mounting to concrete wall (ex. Drill, masonary bit, etc...) it is recommended that someone with
experience using these types of tools perform this type of installation.
•- If using powered tools always wear safety goggles –
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
MOUNTING BRACKET TO WALL
1. You must first choose a sturdy, unobstructed (clear of ceiling, fans, electrical wiring, etc...) mounting location
approximately 80” from floor to top of Mounting Bracket.
IMPORTANT: Mounting to drywall only is NOT recommended.
2. If mounting to a wall with a solid wood backer-board; Use all four (4) Phillips screws provided; DO NOT
OVERTIGHTEN.

Page 2 of 4
006245 Rev K Date 06-26-13 JWC
3. If mounting to a cement or concrete-block wall use toggle bolts or appropriate concrete anchors –capable of at
least 30 lbs. holding strength.
4. Install (4) screws –through holes in bracket and into wall –tighten securely & snap on plastic cover.
SEE PHOTOS –NEXT PAGE
INSTALL ROD & CURTAIN
5. Place short end of Rod Assmbly through both holes on Wall Bracket; Nylon washer should make contact with
top of wall bracket to give the 340 screen smooth operation when rotating.
6. “Unsnap” curtain hook latches and attach curtain hooks through holes in Vinyl Panel, then around Rod
Assembly.
7. Secure hooks to Rod Assembly by “snapping” the hook latches.
PANEL REPLACEMENT
8. To replace Vinyl Panels, remove the curtaing hooks from the vinyl panel by “unsnapping” hook latch.
9. Replace old vinyl panel with a new vinyl panel and re-install curtain hooks.
CARE & MAINTENANCE OF YOUR SCREEN
10. PERIODICALLY CHECK ALL MOUNTING HARDWARE FOR TIGHTNESS
11. To clean Vinyl Panels, use only mild liquid soap and water.
Wrinkles in Vinyl –Storage and shipping causes wrinkles of the vinyl of your Winco Screen; This is normal. Please allow 1-2
weeks at room temperature (approx. 70+ degrees) to allow for vinyl to return to original appearance.

Page 3 of 4
006245 Rev K Date 06-26-13 JWC
Visit our website for a complete parts list catalog of your chair or call Customer Service @ 1-800-237-3377 to
request it by mail.
Other Quality Winco Medical Furnishings You May Be Interested In:

Page 4 of 4
006245 Rev K Date 06-26-13 JWC
Visit us online at www.wincomfg.com
Design, appearance, parts, & construction are subject to change without notice